Roca W12 User manual
»2 Speed, self-parking
»Heavy Duty motor, 12Nm
»Wipershaft in stainless steel
»Various sweep angle: 45 - 110°
»CE approved; EMC protected
»Spray proof IP65
»Insulated ground for metal, plastic and wooden boats.
»Powers up to 610 mm x 560 mm /24˝ x 22˝ arm/blade
combinations.
WIPER MOTOR | W12
Mounting Instructions
Before installation please read these instructions.
Centerline for sweep area
Wiper arm
22.5°
2
Alternative fastening
C - C 145
5.71"
16 - 17
0.67"
5 / 0.2"
1
Mounting instructions - Wiper motor | W12
Keep battery main switch turned off during operation inside of the wiper motor
1. Remove cover with enclosed torx key.
2. Locate the mounting position .Drill mounting holes (template provided on the box).
Mount motor to the surface. See picture 1.
3. The motor is pre-set to 45° sweep and right parking position. To set the arm in correct position do as following:
a. Find the centerline of the desired sweep area.
b. Attach the wiper arm 22.5° from the centerline (use the attached template below). See picture 2 and 3.
4.
Loosen the two screws on the angle plate with the enclosed torx key. See picture 5. Move the arm to desired end position of
sweep area. See picture 4. Tighten the two screws rmly.
5.
To set the self-parking feature to park in the left position use the enclosed torx key and turn the parking selector clockwise See
picture 5.
6. Connect wires as shown in picture 6.
If using Roca switch 466099/466208 use 6a. For all other switches use 6b.
Use a 5Amp fuse for 12V and 3Amp for 24V.
7. Make sure the gasket is in right position and replace the cover on the motor with the screws taken out.
Note: If the arm sweeps too far out on both sides, the sweep angle needs to be reduced, repeat
point 5 above. If the arm goes too far on one side only then you did not start with the arm in
center of the sweep. Remove the arm and place it at the correct position.
Instruction sheet
22.5°
Centerlineforsweeparea
3c
Centerline for sweep area
Wiper arm
22.5°
2
End
position
4
Parking selector
Angle plate
Loosen
torx screws
5
Instruction sheet
22.5°
Centerline for sweep area
3b
22.5°
Instruction sheet
Centerline for sweep area
3a
+ -
Battery
Fuse
G
FSP
Switch circuit
P = Parking
S = Slow
F = Fast
G = Ground
Right park pos
CCW
5A/12V
3A/24V
6b
+ -
Fuse
5A/12V
3A/24V
P
G
FS
Rocker switch - 466099
Actuator - 466026
Battery
6a
59
L1
L2
Ø 13,8 / 0.54"
Std.splines z=72
13,8
0.54"
170
100
3.9"
6.69" 2.32"
5.71"
0.67"
C-C 145
17
27
1.06"
5
0.2"
M16x1
OPTIONAL:
Wiper arm, Wiper blade, Control box, Spray system
Adjustable windshield arms
Coated stainless steel with UV-protection.
Wiper blade
Wiper arm adjustable. Hook-type connection.
310–440 mm / 12”–17”
480–610 mm / 19”–24”
Wiper arm adjustable TIP 40° R/L. Hook-type connection.
340–470 mm / 13.5”–18.5”
480–610 mm / 19”–24”
Pantograph arm adjustable. Hook-type connection.
340–470 mm / 13.5”–18.5”
480–610 mm / 19”–24”
Wiper blade Black powder coated – Natural rubber.
280 mm / 11” 430 mm / 17”
305 mm / 12” 455 mm / 18”
330 mm / 13” 480 mm / 19”
355 mm / 14” 508 mm / 20”
380 mm / 15” 533 mm / 21”
405 mm / 16” 560 mm / 22”
3 Way toggle switch
with or without
LED backlight.
Roca wiper control
for synchronized, two speed and in-
termittent drive of up to 3 motors.
Washer systems
For more info: www.rocamarine.com
Limited warranty
»Roca warrants the wiper motors to be free from defective
material and workmanship for a period of 3 years from the
date of purchase.
»This warranty does not apply to failure or damage caused
by improper installation, misuse, lightning strike or dam-
age from a power surge.
»If failure occurs during this period, return it to your dealer
for repair or replacement.
533145_Inst_5330xx | 2010-09-20 RE/LW/MB
T
H
R
E
E
Y
E
A
R
S
3
W
A
R
R
E
N
T
Y
VARIATIONS:
Max length: Voltage input:
L1 L2 12V 24V
16 / 0.63” 38 / 1.5” 533011 533012
41 / 1.61” 64 / 2.5” 533021 533022
66 / 2.6” 90 / 3.5” 533031 533032
Other Roca Marine Equipment manuals
