Rocket Fish rf-tvmfm02 User manual

1 Install the TV bracket
Option 1: Installing for a at mounting surface
1Align the TV bracket (A) with the screw holes on the back of the TV.
2Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV bracket,
then insert the M4 screws (F), M5 screws (J), or M6 screws (L or M) through the washers.
3Tighten the screws until they are snug against the TV bracket. Do not over tighten.
2 Install the arm assembly
Note: Any material covering the wall must not exceed 5/8 in. (16 mm).
Option 1: Installing to a wood stud wall
1Locate the stud. Verify the center of the stud with an awl
or thin nail or use an edge-to-edge stud nder.
2Level the arm assembly (B) and mark the hole locations.
3Drill pilot hole to a depth of 3 in. using a 7/32 in. diameter drill bit.
4Align the arm assembly (B) with the pilot holes.
5Place the washers (D) over the holes in the
arm assembly, insert the lag bolts (E)
through the washers, then tighten
the lag bolts only until the washers
are pulled rmly against the arm
assembly.
CAUTION: Avoid potential injuries or
property damage!
DO NOT over-tighten the lag bolts (E).
Option 2: Installing for an obstructed mounting surface
Note: Use additional washers (H) with M4/M5 hardware only.
1Align the TV bracket (A) with the screw holes on the back of the TV.
2Place the M4/M5 washers (H) or M6/M8 washers (O) over the holes in the TV bracket,
then insert the M4 screws (G), M5 screws (K), or M6 screws (N or Q) through the washers.
3Tighten the screws until they are snug against the TV bracket. Do not over tighten.
Option 2: Installing to a solid concrete or concrete block wall
1Level the arm assembly (B) and mark the hole locations.
2Drill pilot hole to a depth of 3 in. using a 3/8 in. diameter drill bit.
3Insert the concrete wall anchors (C) into the pilot holes
and make sure that the anchors are seated ush with
the concrete surface.
4Align the arm assembly (B) with the anchors.
5Place the washers (D) over the holes in the arm assembly,
insert the lag bolts (E) through the washers, then tighten
the lag bolts only until the washers (D) are pulled rmly
against the arm assembly.
CAUTION: Avoid potential injuries or property damage!
DO NOT over-tighten the lag bolts (E).
QUICK SETUP GUIDE
RF-TVMFM02
Tools you will need:
• Stud nder
• Awl
• Pencil
• Level
• Tape measure
• Phillips screwdriver
• Hammer (concrete only)
• Socket wrench with
1/2 in. socket or
adjustable wrench
• 7/32 in. wood drill bit
• 3/8 in. masonry drill bit
(concrete only)
• Power drill
Package contents
ATV bracket (1)
BArm assembly (1)
Lag bolt bag
CConcrete anchor (2)
DLag bolt washer (2)
E5/16 in. × 2-3/4 in. lag bolt (2)
M4 bag
FM4 × 12 mm screws (4)
GM4 × 30 mm screws (4)
HM4/M5 washers (8)
IM4/M5 spacers (4)
M5 bag
JM5 × 12 mm screws (4)
KM5 × 30 mm screws (4)
Thank you for choosing the Rocketsh RF-TVMFM02.
The RF-TVMFM02 TV mount is designed to support a
at-panel TV weighing up to 60 lbs. (27.2 kg).
M6 bag
LM6 × 12 mm screws (4)
MM6 × 20 mm screws (4)
NM6 × 35 mm screws (4)
OM6/M8 washers (4)
PM6/M8 spacers (4)
M8 bag
QM8 × 40 mm screws (4)
Hex key bag
R3/16 in. hex key (1)
S5/32 in. hex key (1)
Cap screw
TCap screw (1)
Cable ties
U8 in. nylon cable ties (5)
M4/M5
M6/M8
M6 ×20 mm M6 ×35 mmM6 ×12 mm
M4 ×30 mmM4 ×12 mm
M5 ×30 mmM5 ×12 mm
M4/M5
M6/M8
M8 ×40 mm
M4 bag
Cap screw
M5 bag
M6 bag
M8 bag Hex key bag
Cable ties
Lag bolt bag
5/16 in. ×2-3/4 in.
3/16 in.
5/32 in.
CAUTION: To prevent property
damage or personal injury, never
drill into mortar between blocks.
Mount wall plate directly onto the
concrete surface.
7 in.
9 7/10in.
7 in.
9-7/10 in.
TV shifts 7 in. from the home position
to full extension.
<5/8 in.
(75 mm)
3 in.
(75 mm)
3 in.
or or
or
or or
Wall
TV
C
M
Y
CM
MY
CY
CMY
K
RF-TVMFM02_10-0565_QSG_V1_EN.eps 1 6/2/2010 6:03:12 PMRF-TVMFM02_10-0565_QSG_V1_EN.eps 1 6/2/2010 6:03:12 PM

IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
CAUTION: Do not use this product for any purpose not explicitly specied
by Rocketsh. Improper installation may cause property damage or
personal injury. If you do not understand these directions, or have doubts
about the safety of the installation, contact Customer Service or call a
qualied contractor. Rocketsh is not responsible for damage or injury
caused by incorrect installation or use.
The weight of your TV must not exceed 60 lb (27.2 kg).The wall must be
capable of supporting ve times the weight of the TV and wall mount
combined.
This product contains small items that could be a choking hazard if
swallowed. Keep these items away from young children!
5-year limited warranty
Visit www.rocketshproducts.com for details.
We’re here for you
www.rocketshproducts.com
For customer service, call:
800-620-2790 (U.S./Canada markets)
3 Mount the TV to the wall
1Slide the top and bottom edges of the arm assembly under the metal tabs on the TV bracket.
2Secure the arm assembly to the TV bracket with the cap screw (T) using the 3/16 in. hex key (R).
5 Adjust the swivel tension
Adjust the swivel tension using the 5/32 in. hex key (S).
HEAVY! You will need
assistance with this step.
4 Adjust the viewing angle
When the television is mounted onto the arm assembly and secured, the assembly can be adjusted to
make the TV level.
1Loosen the two screws on the arm assembly using the 5/32 in. hex key (S).
2Adjust the TV ± 6° either clockwise or counter-clockwise.
3Retighten the screws.
6 Manage the cables
Use cable ties (U) to bundle and secure the TV cables to the arm assembly.
© 2010 BBY Solutions, Inc., All Rights Reserved.
Distributed by Best Buy Purchasing, LLC 7601 Penn Avenue South, Richeld, MN USA
55423-3645
Distribuido por Best Buy Purchasing, LLC
Best Buy Imports, S. de R.L. de C.V. Av. Santa Fe 485, Segundo Piso, Colonia Cruz Manca,
Programa Parcial de Desarrollo Santa Fe, Delegación Cuajimalpa, Distrito Federal, México
05349
ROCKETFISH is a trademark of BBY Solutions, Inc. All other products and brand names are
trademarks of their respective owners.
6907-002018 <00>
ENGLISH 10-0565
Leveling
10°10°
7 Adjust the tilt
Adjust the tilt of the TV forward or backward 10° using your ngers or the 3/16 in. hex key (R).
C
M
Y
CM
MY
CY
CMY
K
RF-TVMFM02_10-0565_QSG_V1_EN.eps 2 6/2/2010 6:03:22 PMRF-TVMFM02_10-0565_QSG_V1_EN.eps 2 6/2/2010 6:03:22 PM