Roger Technology H70/104AC User manual

Quick Start H70/104-105AC
Rev01 17/08/2020
ROGER TECHNOLOGY
Via S. Botticelli 8 • 31021 Bonisiolo di Mogliano Veneto (TV) • ITALIA
P.IVA 01612340263 • Tel. [phone] • Fax. [phone]
[e-mail] • www.rogertechnology.com
APower supply H07RN-F 3x1,5 mm2double insulated cable
1Photocell - Receiver 4x0,5 mm2double insulated cable (max.20 m)
2Photocell - Transmitter 2x0,5 mm2double insulated cable (max.20 m)
3Flashing lamp unit 2x1 mm2double insulated cable (max.10 m)
4Antenna RG58 50 Ohm cable for external use (max.10 m)
5Selector / Keypad Cavo 3x0,5 mm2 cable (max.20 m)
1. Typical installation
H70/104-105AC is the range of 230V AC digital controllers installed with the M30, H30, R30, G30 and E30 product series for
sliding gate applications.
EN
1
A
1
5
2
2
3
4

2. Electrical connections
3. Display: functions and settings
PROG TEST
+
-
Back
Programming Check error alarms
PARAMETER PARAMETER
VALUE
Increase value
Decrease value
Next
PROG TEST
+
-
Accessories illustrated are indicative only
LN
M
11
412 3789 106
27 28
12 13 14 15 16 17 18 19
PROG TEST
+
-
COM
AP
CM
CH
COR
LAM
COM
AP
CO
CH
PE
OR
PP
ST
CS1
CS2
FT1
FT2
SC
24V
COM
CORLNPE LAM
24V~
SC
COM
FT2
FT1
COS2
COS1
ST
PP
22
ORO
23
PED
24
CH
25
AP
26
COM
ANT
F1
FUSE
F6,3A
F6,3A
F2
FUSE
F315mA
F315mA
H93/RX22A/I
RICEVITORE RADIO
RADIO RECEIVER
N
230Vac
L
PR1
PR2
MOTORE
MOTOR
verde / green
rosso/ red
blu / blue
ENCFC
SB
Orologio / Timer
Apertura parziale
Paral opening
Passo passo / Step by step
Chiusura / Closing
Apertura / Opening
Spia cancello aperto /
Open gate light 24 Vac 2 W
STOP
Bordo sensibile 1
Safety edge 1
Bordo sensibile 2
Safety edge 2
Antenna
RG58 max 10 m
CONDENSATORE
CAPACITOR
H70/104AC
M30
H30
R30
G30
E30
230Vac
ANT
FUSIBILE F200mA
FUSE F200mA
Marrone/Brown
Marrone/Brown
Blu/Blue
RG58 max 10 m
11
910
12 13 14 15 16 17 18 19
LAM
24V~
SC
COM
FT2
FT1
COS2
COS1
ST
PP
2
ANT
FIFTHY/230
LN
12 3
LNPE
N
230Vac
L
RXTX
P1
12 12345
11 12 13 14 15 16 17 18 19
24V~
SC
COM
FT2
FT1
COS2
COS1
ST
PP
ANT
PP
ST
CS1
CS2
FT1
FT2
SC
24V
COM
COM COM COM
24V
24V FT1
CONNECTION WITH 1 PAIR OF PHOTOCELLS
RECOMMENDED USE for Series
F2ES - F2S photocells
CONNECTION WITH FLASHING LIGHT

4. Before starting ...
e) Select the appropriate self-acquisition procedure for your installation:
A) SELF-ACQUISITION PROCEDURE WITH ENCODER ENABLED, WITH OR WITHOUT LIMIT SWITCHES
B) SELF-ACQUISITION PROCEDURE WITH LIMIT SWITCHES, WITHOUT ENCODER
C) SELF-ACQUISITION PROCEDURE WITHOUT LIMIT SWITCHES AND WITHOUT ENCODER
d) Press the TEST button Possible alarms and safety device messages:
SEE ACQUISITION PROCEDURE
00 No safety device in alarm state and no limit switch activated.
Sb (Sb) Release handle or lock open.
18 STOP contact (N.C.) open.
Jumper the STOP contact.
17 Sensing edge contact COS1 (N.C.) is open. Check connection. If sensing
edge is not installed, disable with 73 00.
16 Sensing edge contact COS2 (N.C.) is open. Check connection. If sensing
edge is not installed, disable with 74 00.
15 Photocell contact FT1 (N.C.) is open. Check connection. If photocell is not
installed, disable with 50 00.
14 Photocell contact FT2 (N.C.) is open. Check connection. If photocell is not
installed, disable with 53 00.
fe Both limit switches in error state. Check connections and settings of limit
switches.
fa If gate is open, gate open limit switch is detected.
fC If gate is closed, gate closed limit switch is detected.
a) Select the position of the motor relative to the gate with the parameter
71 . The default setting for this parameter is with the motor installed
on the right hand side of the gate (seen from interior side).
b) Adjust the (mechanical or magnetic) limit
switches so that, once triggered, the gate stops
slightly before it reaches the mechanical stop.
To verify the correct direction of position with
respect to the passage press TEST.
If the gate is in closed position, FC will be
displayed; if the gate is in open position, FA will
be displayed.
GATE OPENS TO LEFT GATE OPENS TO RIGHT
CLOSING LIMIT SWITCH OPENING LIMIT SWITCH
WARNING: PARAMETER 30 MUST BE THE SAME AS 01
PROG TEST
+
-
PROG
TEST
+
-
PROG TEST
+
-

5. Acquisition procedure (with encoder enabled, with or without limit switches - 75 01)
5. Acquisition procedure (with limit switches, without encoder)
5. Acquisition procedure (without limit switches and without encoder)
1. Press and hold PROG for 4 seconds.
2. APP- appears on the display.
3. Press PROG.
4. AUTO appears on the display.
5. The gate starts to open.
6. When the gate is open after a few seconds AUTO flashes for 2 seconds.
7. When the message AUTO stops flashing sul display the gate starts closing.
8. When the gate is closed, the safety device symbols are displayed.
1. Press and hold PROG for 4 seconds.
2. APP- appears on the display.
3. Press PROG.
4. The gate starts to open.
5. AP1 appears on the display.
6. Once the relative limit switch is activated, the gate stops briefly.
7. PA flashes on the display for 2 seconds.
8. After this 2 second interval, gate closes automatically. The message CH1 appears on the display.
9. When the gate is closed, the safety device symbols are displayed.
1. Press and hold PROG for 4 seconds.
2. APP- appears on the display.
3. Press PROG.
4. The gate starts to open.
5. AP1 appears on the display.
6. When the gate reaches the open position mechanical stop, wait 3-4 seconds then press PROG.
7. PA flashes on the display for 2 seconds.
8. After this 2 second interval, gate closes automatically. The message CH1 appears on the display.
9. When gate reaches the closing mechanical stop, wait 3-4 seconds then press PROG.
10. When the gate is closed, the safety device symbols are displayed.
PROG
AP P- AU to
x4 s
PROG
1 click OPENING OPEN
CLOSING CLOSE
Yes
AU
AU
to
to
PARTIALLY
OPEN
AU to
PROG
AP P-
x4 s
x2 s
PROG
1 click
Yes
PA
PA
CH 1
AP 1
OPENING OPEN
CLOSING CLOSE
PARTIALLY
OPEN
PROG
AP P-
x4 s
x2 s
PROG
1 click
PROG
1 click
Yes
PA
PA
CH 1
AP 1
3-4 s
PROG
1 click
3-4 s
OPENING OPEN
CLOSING CLOSE
PARTIALLY
OPEN

6. Setting basic parameters
 Set deceleration space (%)  Set deceleration space (%)
 Set deceleration during closure  Set deceleration during opening
 Set initial acceleration during opening  Set initial acceleration during closing
 Set braking time
 Set braking force
 Adjustment of the motor torque during the total opening and closing manoeuvre
 Set motor torque during deceleration
 Set motor torque boost at starts of manoeuvre
 Set obstacle detection sensitivity during deceleration
 Set obstacle detection sensitivity during manoeuvres
 Setting reverse time after activation of sensing
edge or obstacle detection
(crush prevention)
IN THE CASE OF COUNTRIES WITH VERY COLD TEMPERATURES WE RECOMMEND THAT YOU VIEW
PARAMETERS 36 AND 37 AND THE ACTIVATION OF THE MAXIMUM STARTING POINT.

7. Programming a NEW transmitter
8. Copying a transmitter
1. Press channel P1 (P2) of the receiver.
2. When LED L1 (L2) ashes 3 times (or 4 times
with rolling code function), press any button
on the transmitter.
3. If LED L1 (L2) remains steadily lit the
transmitter has been stored correctly
1. Press buttons A and B on the NEW
transmitter simultaneously.
2. The LED ashes for 5 s.
3. Hold button (A) only on the NEW transmitter
you want to store.
4. The LED ashes 3 s.
5. Hold the previously stored transmitter as
close as possible to the NEW transmitter.
6. Press button (A) on the OLD transmitter.
7. The LED lights for 1 s to conrm that the copy
procedure was successful.
P1
L1 L2
P2 P1
L1 L2
P2
ON
P1
L1 L2
P2
1 click
x5 s x3 s x1 s
AAA
A
B
OLD
This document is a basic quick guide for the initial installation of a sliding gate motor.
For complete information concerning the control unit, the motor and the accessories mentioned in this quick guide, see the technical manuals available in the B2B area of the
website www.rogertechnology.it