Roller Grill PZ 430 S Operation manual

INSTRUCTIONS FOR USE AND INSTALLATION
PIZZA OVENS
PZ 430 S / PZ 430 D / PZ 4302 D
Made in France
November 2011

PIZZA OVENS
PZ 430 S / PS 430 D / PS 4302 D
Congratulations for the acquisition of this upmarket appliance made in France. You
chose an appliance which alloys the best technical qualities with a big user-friendliness.
We wish you the biggest contentment
1. SECURITY INSTRUCTIONS
Please respect these instructions scrupulously to avoid any risk of fire, electric shock,
scald or other wounds and damage. During the use of this appliance, fundamental cir-
cumspection of security must always be noticed, such as:
-Take into account the instructions and keep it systematically with the appliance.
-Install the appliance always in instructions respect. A 10 cm distance minimum with
the partition or the wall is necessary.
-Protect the appliance from direct light of the sun, frost and humidity.
-Never leave the appliance within the reach of children or disabled persons without
surveillance.
-Never move the appliance when it is working or when the surfaces of cooking are
still hot.
-Check that the appliance is definitely off before connecting it up or disconnecting it.
-Do not touch the hot surfaces of the appliance. The temperature of the hot surfaces
can be very important when the appliance is working. Always use handles and control
knobs.
-Do not use the appliance for other functions than determined use.
-Do not leave the electrical cord in contact of hot surfaces.
-The appliance should not be used close to combustible materials.
-During use, look after not to obstruct hearings of aeration of the appliance
-To avoid any electric shock, never plunge the appliance, the cord or plug in water or
quite other liquid.
-If the cord is harmed, it must be replaced by the producer, his after sale service or
persons of similar skills to avoid any risk.
-Entrust repairs only to a skilled person.
-Use only spare parts of origin.
-At the end of cooking, before cleaning the appliance, do not forget to disconnect it.
2. CONTENTS OF CARDBOARD PACKAGING
Device: a pizza oven
Accessories: - a fire stone
-the present note
See exploded views for PZ 430 S / PZ 430 D / PZ 4302D at the end of the document
17

Nomenclature PZ 430 2D
Spare parts PZ 430 2D
Rep Code Qty Pièce Spare part
135124 1Déflecteur gauche Left deflector
2D04039 2Résistance+tube quartz haut arrière Rear top quartz tube+heating element
3D04038 4Résistance+tube quartz haut avant Front top quartz tube+heating element
435114SE 1Platine avant Control panel
5D04039 4Résistance + tube quartz bas Bottom quartz tube+heating element
6F07024 1Chamotte Fire stone
7A08009 1Voyant vert Green pilot light
835113 12 Contre poids Against weight
935119SE 1Porte Door
10 35120SE 1Contre porte Inner door
11 H01075 2Vitre Glass
12 A15060 1Poignée Handle
13 A08003 1Voyant orange Orange pilot light
14 A13017 4Pied Foot
15 A14078 3Bouton Knob
16 35116 1Dessus Top
17 B04104 1Tube vapeur Stream tube
18 A18022 1Support lampe + lampe Lamp + lamp holder
19 A16014 1Bornier 6 plots Six holes domino
20 35123 1Fond arrière de cuve Tank back rear
21 A05008 1Contacteur Contactor
22 35125 1Déflecteur droit Right deflector
23 C01010 1Cable Cord
24 A10032 1Serre cable Cord closer
25 35099 2Flasque Side casing
26 35115 1Socle Base
27 A02029 1Minuterie 15 'Timer 15 '
28 A06042 1Thermostat Thermostat
29 A04006 1Régulateur Regulator
16
3. CONFORMITY OF USE
Use the appliance only to cook fresh or frozen products like pizzas, quiches, lasagnes,
pies, bread, pastries….
4. WAY OF FUNCTIONING
These pizza ovens are made for the fast cooking of fresh or deep frozen products.
Cooking is made thanks to 8 quartz tube heating elements (PZ 430 S/PZ 430 2D) or 16
quartz tube heating elements (PZ 430 D) which produce a maximum infrared radiation.
A fire stone ensures an excellent spread of heat for an homogeneous cooking of the
dough.
To turn on the oven, select the heating time by turning the timer control knob (n°1 on
picture), the green pilot light (n°2 on picture) ignites.
You can put the timer on the continuous position by turning the timer control knob on the
left. In this case, do not forget to turn off the oven at the end of the service.
Turn on the thermostat control knob (n°3 on picture) on the wished position, the orange
pilot light (n°4 on picture) ignites. The upper quartz tubes are running. Turn on the regu-
lation knob (n°5 on picture) on the wished power. The lower quartz tubes ignite.
You can reach full power by turning the knob on C position.
15 mn timer Thermostatic pilot light
On/off pilot light
Regulator
Thermostat 3
1
2
3
5
2
4
4
5
3
1

5. FUNCTIONING / MANIPULATION
a) Installation / assembly:
-Unpack carefully the device of its packaging.
-Place it on a plane and heatproof surface.
-Never place the device near a wall or near a partition makes of combustible materials
even if it is very well isolated.
-A distance of minimum 10 cm with the partition or the wall is necessary.
-Remove the protective film around the device and unpack the fire stone
b) First starting:
During the first use, warm your machine up outside to evacuate residual smokes of
manufacturing oil from the metallic parts. This may emit a slight smell for a few mo-
ments.
First cleaning
Clean the device before the first use. (See 6. Cleaning)
Connection of the device
-Check that the tension and the frequency of the electricity network suit to the values
indicated on the descriptive plate.
-Check that neither the cord nor the plug are damaged. If necessary, it has to be re-
placed by the manufacturer, its after sale service or any qualified person to avoid any
risk.
-Make sure that every control knob is positioned on 0.
-Unwind completely the electric power cable and connect it in a plug connected with
the earth.
-The device is connected.
NB: in case of connection of the device in a plug without earth protection or directly on
the electricity network, confide its connection to a qualified person .
c) Use of device :
Elements of command and display
Command/Display Function
Regulator (n°5 on picture) Temperature setting of the bottom heating element
Thermostat (n°3 on picture) Temperature setting inside the cooking chamber
Green pilot light
(n°2 on picture) Machine on (pilot light on) Machine off (pilot light off)
Orange pilot light
(n°4 on picture) Warming up (pilot light on) Desired temperature reached (pilot light off)
15 min timer (n°1 on picture) On/off + Cooking time
415

Nomenclature PZ 430 D (2 cordons)
Spare parts PZ 430 D (2 cords)
Rep Code Qty Pièce Spare part
135111 1Déflecteur gauche Left deflector
2D04041 4Résistance+tube quartz haut arrière Rear top quartz tube+heating element
3D04040 4Résistance+tube quartz haut avant Front top quartz tube+heating element
435106SE 1Platine avant Control panel
5D04041 8Résistance + tube quartz bas Bottom quartz tube+heating element
6F07025 2Chamotte Fire stone
7A08009 2Voyant vert Green pilot light
8A13017 4Pied Foot
935113 24 Contre poids Against weight
10 35095SE 2Porte Door
11 35096SE 2Contre porte Inner door
12 H01076 4Vitre Glass
13 A15061 2Poignée Handle
14 A14078 6Bouton Knob
15 35091 1Dessus Top
16 B04104 1Tube vapeur Stream tube
17 A18022 2Support lampe + lampe Lamp + lamp holder
18 A16014 1Bornier 6 plots Six holes domino
19 35110 1Fond arrière de cuve Tank back rear
20 35112 1Déflecteur droit Right deflector
21 C03013 2Cordon avec prise Cord with plug
22 A10032 2Serre cable Cord closer
23 35109 2Flasque Side casing
24 35088 1Socle Base
25 A08003 2Voyant orange Orange pilot light
26 A02029 2Minuterie 15 'Timer 15 '
27 A06042 2Thermostat Thermostat
28 A04006 2Régulateur Regulator
14 5
Putting on
Turn on the timer control knob (n°1 on picture) on wished cooking time. The green
pilot light (n°2 on picture) ignites
Turn on the thermostat control knob (n°3 on picture) on the wished position: the or-
ange pilot light (n°4 on picture) ignites. The machine is warming up.
Once orange pilot light (n°4 on picture) is off, the machine reached the wished tem-
perature and is ready for cooking.
A few tips
To obtain much better results, we advise to regulate the oven as follows:
-A fresh pizza (diam.40cm) with a thin dough will be ready in 3 min, thermostat 350 °
C, regulator on position 9.
-A deep-frozen pizza (diam. 40cm) with a thick dough will be ready in 4 min, thermo-
stat 320°C, regulator on position 7
You can use your pizza oven in continuous by turning the timer on left side from po-
sition 0. Caution : do not forget to turn off your pizza oven after use.
Temperature setting
Set the temperature by positioning the thermostat (n°3 on picture) to the desired
temperature. The orange pilot light (n°4 on picture) switches on if a higher level
of temperature is required and switches off when the same is reached.
The energy regulator enables you to adapt the heating power of the bottom heat-
ing element regarding the thickness of the dough to be cooked. The thicker is
the dough, the higher the temperature has to be. The cooking of the pizza dough
is essentially made through the bottom.
Stopping the appliance
Set the thermostat control knob (n°3 on picture) on 0
Set the timer (n°1 on picture) on 0 : the appliance is no longer functioning.
Disconnect the power cable.
Clean the appliance. (see 6. Cleaning)
d) Breakdown / repair:
In case of breakdown or of damaged part, please call your after-sales service and
confide any technical operation to qualified person.
When you contact the after-sales service of your distributor or your store, give him
the complete reference of your device (commercial name, type and serial number).
This information appears on the visible descriptive plate behind the device.

6. CLEANING AND MAINTENANCE
Disconnect the device.
-Let cool completely the device before any technical intervention or cleaning.
-Clean the fire stone when it is warm by scratching it slightly with a wire brush or a
small emery cloth to remove residues.
-Never clean the fire stone under water-Never clean the quartz tubes when they are
hot
-Avoid touching quartz tubes with your fingers but use a cloth moistened with spirit.
-Clean regularly the external walls of your device with warm water and wash liquid:
avoid the abrasive towelling. Rinse your device with a wet sponge.
-Never clean the device under a water jet, the infiltrations would risk to damage it in a
irreparable way.
-Never immerse the device, the cord or the plug in the water or quite other liquid to
avoid any electric shock.
-During a prolonged non-use, we recommend you strongly to keep the device
shielded from the humidity.
7. TECHNICAL SPECIFICATIONS
Wires colours correspondence Phase 1Brown
Phase 2Black
Phase 3Grey
Neutral Blue
Earth Yellow-Green
8. NORMS AND LEGALS DISPOSALS
The device is conform to :
IEC 60335-1
IEC 60335-2-36
EN 55014
EN 55014-2
EN 61000-3-2
EN 61000-3-3
Model PZ 430 S PZ 430 D
Outside dimensions 670x580x270 mm 670x580x500 mm
Weight 31 Kg 54 Kg
Power 3000 W 6000 W
No element 8 16
Current 13 A 13 A/Phase
Voltage 220-240 V ~ 380-415 V 3 N~ ou
2x 220-240 V ~
PZ 430 2D
895x580x270 mm
41Kg
5000 W
8
11 A/Phase
380-415 V 3 N~
Inside dimensions 430X430 mm 2x (430x430) 660x430
613

12
Nomenclature PZ 430 D (triphasé)
Spare parts PZ 430 D (3 phases)
Rep Code Qty Pièce Spare part
135111 1Déflecteur gauche Left deflector
2D04041 4Résistance+tube quartz haut arrière Rear top quartz tube+heating element
3D04040 4Résistance+tube quartz haut avant Front top quartz tube+heating element
435106SE 1Platine avant Control panel
5D04041 8Résistance + tube quartz bas Bottom quartz tube+heating element
6F07025 2Chamotte Fire stone
7A08009 2Voyant vert Green pilot light
8A13017 4Pied Foot
935113 24 Contre poids Against weight
10 35095SE 2Porte Door
11 35096SE 2Contre porte Inner door
12 H01076 4Vitre Glass
13 A15061 2Poignée Handle
14 A14078 6Bouton Knob
15 35091 1Dessus Top
16 B04104 2Tube vapeur Stream tube
17 A18022 2Support lampe + lampe Lamp + lamp holder
18 A16014 1Bornier 6 plots Six holes domino
19 35110 1Fond arrière de cuve Tank back rear
20 35112 1Déflecteur droit Right deflector
21 C01010 1Cable Cord
22 A10032 1Serre cable Cord closer
23 35109 2Flasque Side casing
24 35088 1Socle Base
25 A08003 2Voyant orange Orange pilot light
26 A02029 2Minuterie 15 'Timer 15 '
27 A06042 2Thermostat Thermostat
28 A04006 2Régulateur Regulator
7
9. ELIMINATION OF THE ELECTRIC AND ELECTRONIC WASTE
The device respects the directives:
2002/96/CE (DEEE) N°34270064800021
2002/95/CE (ROHS)
2006/95 CE
2004/108 CE
Reach rule
Never put the device among household waste.
The device must be put down in a centre of recycling for the electric equipments.
The materials of the device are indeed reusable. By eliminating correctly the electric and
electronic wastes, the recycling and quite other shape of re-use of worn equipments, you
participate in a significant way in the environmental protection.
For any information about the collection of electric and electronic waste, please contact
your distributor.
10. GUARANTEE
Conditions of guarantee
The guarantee applicable to any device is the commercial guarantee of the distributor or
the retailer. Please contact the store where you bought your device to know the precise
conditions.
The guarantee grants no right for damages.
The dispositions which follow are not exclusive of the profit of the legal guarantee
planned by articles 1641 and following ones of the Civil code relative to the defects and
the latent defects.
Exclusion clauses of the guarantee
Bad installation and bad maintenance, in particular if they do not respect current
regulations or instructions appearing in this user guide.
Cannot benefit from the guarantee the repairs required as a result of false operations, of
inappropriate use, of carelessness or of excess loads of the device, as well as those re-
sulting from variations of the power supply, over tension or from defective installations.
The damage due to shocks, bad weather is not flatware by the guarantee. The material
travels at the risks of the user; in case of delivery by carrier, the consignee has to have
reservations towards the carrier before any delivery of the device.
The guarantee comes to an end in case of intervention, of repair, of modification by no
qualified persons, or of use in inappropriate purposes.

811

10
Nomenclature PZ 430 S
Spare parts PZ 430 S
Rep Code Qty Pièce Spare part
135101 1Déflecteur gauche Left deflector
2D04041 2Résistance+tube quartz haut arrière Rear top quartz tube+heating element
3D04040 2Résistance+tube quartz haut avant Front top quartz tube+heating element
435087SE 1Platine avant Control panel
5D04041 4Résistance + tube quartz bas Bottom quartz tube+heating element
6F07025 1Chamotte Fire stone
7A08009 1Voyant vert Green pilot light
835113 12 Contre poids Against weight
935095SE 1Porte Door
10 35096SE 1Contre porte Inner door
11 H01076 2Vitre Glass
12 A15061 1Poignée Handle
13 A08003 1Voyant orange Orange pilot light
14 A13017 4Pied Foot
15 A14078 3Bouton Knob
16 35091 1Dessus Top
17 B04104 1Tube vapeur Stream tube
18 A18022 1Support lampe + lampe Lamp + lamp holder
19 A16013 1Bornier 3 plots Three holes domino
20 35100 1Fond arrière de cuve Tank back rear
21 35102 1Déflecteur droit Right deflector
22 C03013 1Cordon avec prise Cord with plug
23 A10032 1Serre cable Cord closer
24 35099 2Flasque Side casing
25 35088 1Socle Base
26 A02029 1Minuterie 15 'Timer 15 '
27 A06042 1Thermostat Thermostat
28 A04006 1Régulateur Regulator
9