ROOMS TO GO KIDS CREEKSIDE 2.0 3744040P User manual

WARNING DANGER
Failure to follow these warnings and assembly instructions could result in serious
injury or death. To help prevent serious or fatal injuries from entrapment or falls:
-
Read all instructions before assembling bunk bed and keep these instructions for future reference.
-
Before each usage or assembly, inspect bunk bed for damaged hardware, loose joints, missing
parts, or sharp edges. DO NOT Use bunk bed if any parts are missing or broken.
-
DO NOT Use substitute parts. Contact your local Rooms To Go or visit www.ROOMSTOGO.COM
for replacement parts and instructional literature if needed.
-
Follow the information on the warnings appearing on the upper bunk end structure and on the carton,
DO NOT REMOVE WARNING LABEL FROM BED.
-
Always use the recommended size mattress or mattress supports, or both to help prevent the likelihood
of entrapment or falls.
-Ensure thickness of mattress and foundation combine does not exceed
10 inches (255mm
) and
mattress surface is at least
5 inches (127mm)
below upper edge of guardrails.
-
Do not allow children under 6 years of age to use the upper bunk.
-
Periodically check and ensure that the guardrail, ladder, and other components are in their proper
position, free from damage, and that all connectors are tight.
-
Do not allow horseplay on or under the bed and prohibit jumping on the bed.
-
Limit top bunk use to one person.
-
Always use the ladder for entering and leaving the upper bunk.
-
Use of night light may provide added safety precaution for a child using the upper bunk.
-
Always use guardrails on both long sides of the upper bunk. If the bunk bed will be placed next to
the wall, the guardrail that runs the full length of the bed should be placed against the wall to
prevent entrapment between the bed and wall.
-
The use of water or sleep flotation mattress is prohibited.
-
This bunk bed meets all the requirements of ASTM 1427-19.
STRANGULATION HAZARD:
Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed; for example, but not limited to, hooks, belts, and jump ropes.
CREEKSIDE 2.0 COLLECTION
THANK YOU FOR YOUR PURCHASE
11/7/2022 Page 1 of 97

11/7/2022 Page 12 of 97
1 Pc
Trundle bed (Add on)
Slats
5
32 Pcs
4
Guardrails
8 Pcs
1 Pc
Allen wrench (included)
5 mm Hex key
1 pc bunkbed end full
24 Pcs
Drywall screw
1
Side rails
16 Pcs
PARTS LIST QTY HARDWARE LIST QTY
6 x 1 1/4"
38300238 100-648
TOOLS NEEDED
2 Pcs
24 Pcs
Phillips screwdriver (not included)
5/16"-18 x 3 3/8" Bolt
FULL/FULL SLAT PACK
35440419 40B-744 TRUNDLE BED ADD ON
38300238 100-648 FULL/FULL SLAT PACK
35640413 40B-704 1 PC BUNKBED END FULL
35640413 40B-704 1 PC BUNKBED END FULL
3744041P FULL/FULL BUNK CHESTNUT
RTG SKU # STYLE # ITEM DESCRIPTION
38300238 100-648 FULL/FULL SLAT PACK
36640414 40B-730
6 PC RAILS (2 GUARD & 4 SIDE RAILS)
P A R T S L I S T
3744040P FULL/FULL BUNK CHARCOAL
RTG SKU # STYLE # ITEM DESCRIPTION
35640401 40G-704 1 PC BUNKBED END FULL
35440407 40G-744 TRUNDLE BED ADD ON
38300238 100-648 FULL/FULL SLAT PACK
35640401 40G-704 1 PC BUNKBED END FULL
36640402 40G-730
6 PC RAILS (2 GUARD & 4 SIDE RAILS)
A
B
C

11/7/2022 Page 13 of 97
then fasten with 1 1/4" screws Repeat step 1 & 2 for top set of side rails
Assemble guardrails and tighten all bolts. For Add on Trundle bed follow assembly instructions inside
MAKE SURE ALL BOLTS ARE TIGHTENED COMPLETELY Trundle bed box, then slide under the bed as shown.
ASSEMBLY INSTRUCTIONS
Assemble bottom side rails.
Install slats, one on each end, two equally spaced in the middle,
STEP 4
STEP 3
B
STEP 2
B
B
A
A
AA
STEP 1
C
C
C
B
A
C
A
A
C
B
A
A
A
A
A
B
A
A
B
A

Twin size mattress- 74" - 75" long and 37-1/2" - 38-1/2" wide
Twin size Bunkie board- 74" long and 37-1/2" wide
Full size mattress- 74" - 75" long and 52-1/2" - 53-1/2" wide
Full size Bunkie board- 74" long and 52-1/2" wide
11/7/2022 Page 14 of 97
Place Bunkie boards (required, sold separately) on top of the slats
Use only correct mattress dimensions and Bunkie board:
PLEASE CONTACT YOUR RETAIL STORE WITH SERVICE OR PARTS REPLACEMENT REQUEST
ASSEMBLY INSTRUCTIONS
STEP 5