ROSE DISPLAYS ANOGOTCHA SQUARE WITH CABLE CLIP AND BALL... User manual

Parts
OneUp Instruction Sheet
AnoGotcha™
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clip
06-5050
T-Top Gotcha
12GT100
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should snap
into place. Fig. 2
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into rail
by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do not
pull on, or push against, the ball chain as
this will cause it to bind in the channel.
Note: For OneUp Application place
the Cable Clip in the center of the
AnoGotcha Holder.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). To close, snap the
AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Instructions for Hanging
Incept-7.29.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2
Ball Chain
96-0302P

Parts
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clip
06-5050
T-Top Gotcha
12GT100
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should snap
into place. Fig. 2
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into rail
by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do not
pull on, or push against, the ball chain as
this will cause it to bind in the channel.
Note: For OneUp Application place
the Cable Clip in the center of the
AnoGotcha Holder.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). To close, snap the
AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
OneUp Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-7.29.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Ball Chain
96-0302P

Parts
Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-7.29.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clips
06-5050
T-Top Gotcha
12GT100
Ball Chains
96-0302P
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into
rail by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do
not pull on, or push against, the ball
chain as this will cause it to bind in the
channel.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6

Parts
Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-7.29.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into
rail by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do
not pull on, or push against, the ball
chain as this will cause it to bind in the
channel.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clips
06-5050
T-Top Gotcha
12GT100
Ball Chains
96-0302P