ROSE DISPLAYS ECONOSTAND WITH ANOGOTCHA User manual

Parts
Instruction Sheet
Step 1
Assemble bottom holder bracket
onto lower pole section (this is the
thicker section of pole).
Step 2
Screw pole onto baseplate.
Tighten securely.
Step 3
Place stand upright. Using
thumbscrew at top of pole, attach
top holder bracket onto pole top.
Step 4
Insert T-Top Gotcha Holder into
the AnoGotcha Shell.
Step 5
Slide AnoGotcha onto brackets.
Step 6
Install end caps after assembly
to brackets.
EconoStand™
Instructions for Assembly
Incept- 9.10.02
EconoStand
components
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
The Gotcha®is a registered trademark and EconoStandTM and AnoGotcha™
are tradmarks of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSEcono/AnoGotcha
1 2
3 4
5 6
Base Plate
Pole
Top
Holder Bracket
Bottom
Holder Bracket
Top
Thumb
Screw
AnoGotcha Shell
12AG400
T-Top Gotcha
Continued on next page

Parts
Instruction Sheet
Step 7
Snap the AnoGotcha Holder com-
pletely open so that hinge is turned up
as far as possible. Insert poster into
holder until top of poster meets top of
holder. To close snap the AnoGotcha
Holder shut.
Note: With large or curling graphics, it
may be easier to insert graphic at one
end and slide into holder from one end
to another.
Step 8
To close snap the AnoGotcha
Holder shut.
Step 9
Adjust height of stand as necessary.
EconoStand™
Instructions for Assembly
Incept- 9.10.02
EconoStand
components
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
The Gotcha®is a registered trademark and EconoStandTM and AnoGotcha™
are tradmarks of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSEcono/AnoGotcha
7 8
Base Plate
Pole
Top
Holder Bracket
Bottom
Holder Bracket
Top
Thumb
Screw
AnoGotcha Shell
12AG400
T-Top Gotcha
9

Parts
Instruction Sheet
Step 1
Assemble bottom holder bracket
onto lower pole section (this is the
thicker section of pole).
Step 2
Screw pole onto baseplate.
Tighten securely.
Step 3
Place stand upright. Using
thumbscrew at top of pole, attach
top holder bracket onto pole top.
Step 4
Insert T-Top Gotcha Holder into
the AnoGotcha Shell.
Step 5
Slide AnoGotcha onto brackets.
Step 6
Install end caps after assembly
to brackets.
EconoStand™
Instructions for Assembly
Incept- 9.10.02
EconoStand
components
The Gotcha®is a registered trademark and EconoStandTM and AnoGotcha™
are tradmarks of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSEcono/AnoGotcha
1 2
3 4
5 6
Base Plate
Pole
Top
Holder Bracket
Bottom
Holder Bracket
Top
Thumb
Screw
AnoGotcha Shell
12AG400
T-Top Gotcha
Continued on next page

Parts
Instruction Sheet
Step 7
Snap the AnoGotcha Holder com-
pletely open so that hinge is turned up
as far as possible. Insert poster into
holder until top of poster meets top of
holder. To close snap the AnoGotcha
Holder shut.
Note: With large or curling graphics, it
may be easier to insert graphic at one
end and slide into holder from one end
to another.
Step 8
To close snap the AnoGotcha
Holder shut.
Step 9
Adjust height of stand as necessary.
EconoStand™
Instructions for Assembly
Incept- 9.10.02
EconoStand
components
The Gotcha®is a registered trademark and EconoStandTM and AnoGotcha™
are tradmarks of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use of
these products. Part #02INSEcono/AnoGotcha
7 8
Base Plate
Pole
Top
Holder Bracket
Bottom
Holder Bracket
Top
Thumb
Screw
AnoGotcha Shell
12AG400
T-Top Gotcha
9