ROSE DISPLAYS ANOGOTCHA FRAME ROUND WITH CABLE AND BALL User manual

Parts
Step 1
Install four (4) corner brackets (2 each
end) into solid rail opposite split rails.
Fig. 1
Step 2
Push remaining solid rails onto rail
from Step 1 to make three (3) sides
of the frame. Fig. 2
Step 3
Slide Gotcha into top and bottom
rails as shown. Fig. 3 & 4
Step 4
Install remaining corner brackets into
ends of split rails. Fig. 5
Step 5
Insert Cable and Ball into end of
AnoGotcha Solid Rail. Fig. 6
Step 6
Assemble split rails onto frame one
at a time. Fig. 7
Instruction Sheet
AnoGotcha™ Frame
Instructions for Hanging
Incept-9.9.02
AnoGotcha™is a trademark of Rose Displays, Ltd. Neither the manufac-
turer nor any sales agent may be held liable for injury, loss or damage
resulting from the use of these products.
Part #02INSAnoGotchaFrameCableBall
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Continued on next page
Figure 1 Figure 2
Figure 3 Figure 4 Figure 5
Figure 6 Figure 7
Cable and Ball
16-0018P T-Top Gotcha Split Rails
Corner
brackets
AnoGotcha
Solid Rail
12AG400

Parts
Step 7
Snap open Gotcha completely (if not
already open) so that bottom hinge us
turned up as far as possible.
Fig. 8
Step 8
Slip graphic into open rails of frame and
all the way into opposite edge of frame.
Fig. 9
Step 9
Snap Gotcha closed. Fig. 10
Instruction Sheet
AnoGotcha™ Frame
Instructions for Hanging
Incept-9.9.02
AnoGotcha™is a trademark of Rose Displays, Ltd. Neither the manufacturer
nor any sales agent may be held liable for injury, loss or damage resulting from
the use of these products.
Part #02INSAnoGotchaFrameCableBall
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 10
Figure 8
Figure 9
Figure 9
Cable and Ball
16-0018P T-Top Gotcha Split Rails
Corner
brackets
AnoGotcha
Solid Rail
12AG400

Parts
Step 1
Install four (4) corner brackets (2 each
end) into solid rail opposite split rails.
Fig. 1
Step 2
Push remaining solid rails onto rail
from Step 1 to make three (3) sides
of the frame. Fig. 2
Step 3
Slide Gotcha into top and bottom
rails as shown. Fig. 3 & 4
Step 4
Install remaining corner brackets into
ends of split rails. Fig. 5
Step 5
Insert Cable and Ball into end of
AnoGotcha Solid Rail. Fig. 6
Step 6
Assemble split rails onto frame one
at a time. Fig. 7
Instruction Sheet
AnoGotcha™ Frame
Instructions for Hanging
Incept-9.9.02
AnoGotcha™is a trademark of Rose Displays, Ltd. Neither the manufac-
turer nor any sales agent may be held liable for injury, loss or damage
resulting from the use of these products.
Part #02INSAnoGotchaFrameCableBall
Continued on next page
Figure 1 Figure 2
Figure 3 Figure 4 Figure 5
Figure 6 Figure 7
Cable and Ball
16-0018P T-Top Gotcha Split Rails
Corner
brackets
AnoGotcha
Solid Rail
12AG400

Parts
Step 7
Snap open Gotcha completely (if not
already open) so that bottom hinge us
turned up as far as possible.
Fig. 8
Step 8
Slip graphic into open rails of frame and
all the way into opposite edge of frame.
Fig. 9
Step 9
Snap Gotcha closed. Fig. 10
Instruction Sheet
AnoGotcha™ Frame
Instructions for Hanging
Incept-9.9.02
AnoGotcha™is a trademark of Rose Displays, Ltd. Neither the manufacturer
nor any sales agent may be held liable for injury, loss or damage resulting from
the use of these products.
Part #02INSAnoGotchaFrameCableBall
Figure 10
Figure 8
Figure 9
Figure 9
Cable and Ball
16-0018P T-Top Gotcha Split Rails
Corner
brackets
AnoGotcha
Solid Rail
12AG400