ROSE DISPLAYS ANOGOTCHA SQUARE WITH CABLE CLIP AND CABLE AND... User manual

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Note: For OneUp Application place
the Cable Clip in the center of the
AnoGotcha Holder.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
OneUp Instruction Sheet
AnoGotcha™
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clip
06-5050
T-Top Gotcha
12GT100
Cable and
Saucer
16-0018SS
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2

Parts
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clip
06-5050
T-Top Gotcha
12GT100
Cable and
Saucer
16-0018SS
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Note: For OneUp Application place
the Cable Clip in the center of the
AnoGotcha Holder.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
OneUp Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2

Parts
Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clips
06-5050
T-Top Gotcha
12GT100
Cable and
Saucer
16-0018SS
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.

Parts
Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-9.27.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQCableClipSaucer
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Place cable onto inner channel of Cable
Clip. The cable should snap
into place. Fig. 2
Step 3
Align one end of the Cable Clip with the
top channel of the aluminum holder. Then
insert one round end, then press down on
the other round end and slide Cable Clip
into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha
Holder, End Caps, Cable Clips and
MultiClips for future projects.
AnoGotcha Shell
12AG400SQ
End Caps
06-5545
Cable Clips
06-5050
T-Top Gotcha
12GT100
Cable and
Saucer
16-0018SS