ROSE DISPLAYS ANOSCREEN WITH ANOFOOT User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
The AnoScreen™ is a registered trademark of Rose Displays, Ltd. Neither
the manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INAnoScreenAnoFoot
Incept-8.15.02
Instruction Sheet
Step 1
Insert corner brackets into ends of
bottom rails, using thumb, as shown
in illustration. 2 brackets per end of
each rail.
DETAIL 1a- Corner bracket tension
tab faces toward outside of frame.
Step 2
Snap one AnoFoot onto both the
left and right sides of each bottom
Ano rail section.
Step 3
Lay out parts as they will be configured
on the floor. (2, 3 or 4 panels)
AnoScreen™
Instructions for Assembly
1 1a
2 3
Parts
(continued on other side)
4
AnoScreen
Corner Bracket
06-3000
AnoFoot™
12-0200 Corner Brackets
Vertical Rails
with Flex Spine
2 Panel
3 Panel
4 Panel
Single rails Split rails

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
The AnoScreen™ is a registered trademark of Rose Displays, Ltd. Neither
the manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INAnoScreenAnoFoot
Incept-8.15.02
Instruction Sheet (side 2)
Instructions for Assembly continued
7
Step 4
Assemble the vertical rail assemblies onto
the upward facing corner brackets already
inserted into the bottom rails. All 4
brackets can go into the vertical rails
at one time, or do one side at a time.
Note: Use the two vertical rails without
flex spine connectors on the outside
edges of the outermost panels.
Step 5
Insert corner brackets into ends
of split rails. 1 per end. Use thumb,
as shown in illustration.
Step 6
Assemble split rails onto top ends
of vertical rails, one inside and one
outside of each panel of the
AnoScreen.
Step 7
Insert and change signs through top
of each panel.
Step 8
Snap AnoScreen corner brackets onto
split rail at a 90˚ angle.
AnoScreen™
4 5
7 6
AnoFoot
Corner brackets
& Split Rails
AnoScreen Corner Bracket

The AnoScreen™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INAnoScreenAnoFoot
Incept-8.15.02
Instruction Sheet
AnoScreen™
Instructions for Assembly
Parts
(continued on other side)
AnoScreen
Corner Bracket
06-3000
1 1a
2 3
4
Step 1
Insert corner brackets into ends of
bottom rails, using thumb, as shown
in illustration. 2 brackets per end of
each rail.
DETAIL 1a- Corner bracket tension
tab faces toward outside of frame.
Step 2
Snap one AnoFoot onto both the
left and right sides of each bottom
Ano rail section.
Step 3
Lay out parts as they will be configured
on the floor. (2, 3 or 4 panels)
AnoFoot™
12-0200 Corner Brackets
Vertical Rails
with Flex Spine
2 Panel
3 Panel
4 Panel
Single rails Split rails

The AnoScreen™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INAnoScreenAnoFoot
Incept-8.15.02
Instruction Sheet (side 2)
Instructions for Assembly continued
7
AnoScreen™
AnoFoot
Corner brackets
& Split Rails
AnoScreen Corner Bracket
Step 4
Assemble the vertical rail assemblies onto
the upward facing corner brackets already
inserted into the bottom rails. All 4
brackets can go into the vertical rails
at one time, or do one side at a time.
Note: Use the two vertical rails without
flex spine connectors on the outside
edges of the outermost panels.
Step 5
Insert corner brackets into ends
of split rails. 1 per end. Use thumb,
as shown in illustration.
Step 6
Assemble split rails onto top ends
of vertical rails, one inside and one
outside of each panel of the
AnoScreen.
Step 7
Insert and change signs through top
of each panel.
Step 8
Snap AnoScreen corner brackets onto
split rail at a 90˚ angle.
4 5
7 6