ROSE DISPLAYS SUPERSNAP WITH CABLE CLIP AND CABLE AND... User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
SuperSnap™
Step 1
Snap the SuperSnap open and insert
poster (top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and
working your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Place cable into inner channel of
CableClip. The cable should
snap into place. Fig. 3
Step 3
Align one end of the CableClip with
the top channel of the plastic holder.
Then insert one round end, press down
on the other round end and slide
CableClip into rail. Fig. 4 Repeat steps
2 & 3 for second CableClip.
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCSaucer
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
Cable Clips
06-5050
SuperSnap
12S300
End Caps
06-5475
Cable and
Saucer
16-0018SS

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
SuperSnap™
Step 1
Snap the SuperSnap open and insert
poster (top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and
working your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Place cable into inner channel of
CableClip. The cable should
snap into place. Fig. 3
Step 3
Align one end of the CableClip with
the top channel of the plastic holder.
Then insert one round end, press down
on the other round end and slide
CableClip into rail. Fig. 4
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCSaucer
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
Cable Clip
06-5050
SuperSnap
12S300
End Caps
06-5475
Cable and
Saucer
16-0018SS

Parts
SuperSnap™
Step 1
Snap the SuperSnap open and insert
poster (top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and
working your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Place cable into inner channel of
CableClip. The cable should
snap into place. Fig. 3
Step 3
Align one end of the CableClip with
the top channel of the plastic holder.
Then insert one round end, press down
on the other round end and slide
CableClip into rail. Fig. 4 Repeat steps
2 & 3 for second CableClip.
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCSaucer
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
Cable Clips
06-5050
SuperSnap
12S300
End Caps
06-5475
Cable and
Saucer
16-0018SS

Parts
Cable Clip
06-5050
SuperSnap
12S300
SuperSnap™
Step 1
Snap the SuperSnap open and insert
poster (top and bottom). Fig. 1
Note: It is easier to open and close the
SuperSnap by starting at one end and
working your way down the holder.
To close, snap the SuperSnap shut.
Fig. 2
Step 2
Place cable into inner channel of
CableClip. The cable should
snap into place. Fig. 3
Step 3
Align one end of the CableClip with
the top channel of the plastic holder.
Then insert one round end, press down
on the other round end and slide
CableClip into rail. Fig. 4
Step 4
Push end caps into place. Fig 5
Suspend poster. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps and
CableClips for future projects.
Instruction Sheet
Instructions for assembly
Incept-11.13.02
The SuperSnap™ is a trademark of Rose Displays, Ltd. Neither the
manufacturer nor any sales agent may be held liable for injury, loss or
damage resulting from the use of these products.
Part #02INSSuperSnapCCSaucer
Figure 2
Figure 5
Figure 3
Figure 1
Finished Look
Figure 4
End Caps
06-5475
Cable and
Saucer
16-0018SS