ROSE DISPLAYS ANOGOTCHA SQUARE WITH MULTICLIPS User manual

Parts
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with the
top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic completely
into holder until edge of graphic meets top of
holder. To close, snap the AnoGotcha Holder
shut. Fig. 5
Note: It is easier to open and close the Gotcha by
starting at one end and working your way down the
holder. With large or curling graphics, it may be
easier to insert graphic at one end and slide into
holder from one end to another
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder, End
Caps and MultiClips for future projects.
OneUp Instruction Sheet
AnoGotcha™
AnoGotcha Shell
12AG400SQ
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQMC
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
End Caps
06-5545
MultiClip
1UP-0101
T-Top Gotcha
12GT100
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2

Parts
OneUp Instruction Sheet
AnoGotcha™
AnoGotcha Shell
12AG400SQ
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQMC
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
End Caps
06-5545
MultiClip
1UP-0101
T-Top Gotcha
12GT100
Figure 2
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with the
top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 3
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic completely
into holder until edge of graphic meets top of
holder. To close, snap the AnoGotcha Holder
shut. Fig. 5
Note: It is easier to open and close the Gotcha by
starting at one end and working your way down the
holder. With large or curling graphics, it may be
easier to insert graphic at one end and slide into
holder from one end to another
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder, End
Caps and MultiClips for future projects.

Parts
Instruction Sheet
AnoGotcha™
AnoGotcha Shell
12AG400SQ
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQMC
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
End Caps
06-5545
MultiClips
1UP-0101
T-Top Gotcha
12GT100
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with the
top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 3 Repeat steps 2 and 3
for second MultiClip.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic completely
into holder until edge of graphic meets top of
holder. To close, snap the AnoGotcha Holder
shut. Fig. 5
Note: It is easier to open and close the Gotcha by
starting at one end and working your way down the
holder. With large or curling graphics, it may be
easier to insert graphic at one end and slide into
holder from one end to another
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder, End
Caps and MultiClips for future projects.

Parts
Instruction Sheet
AnoGotcha™
AnoGotcha Shell
12AG400SQ
Instructions for Hanging
Incept-7.31.02
AnoGotcha™is a trademark and Gotcha®is a registered trademark of Rose
Displays, Ltd. Neither the manufacturer nor any sales agent may be held
liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaSQMC
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
End Caps
06-5545
MultiClips
1UP-0101
T-Top Gotcha
12GT100
Figure 2
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Squeeze sides of MultiClip together. Fig. 2
Step 3
Align the bottom rail of the MultiClip with the
top channel of the aluminum holder. Slide
MultiClip into rail. Fig. 3 Repeat steps 2 and 3
for second MultiClip.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). Insert graphic completely
into holder until edge of graphic meets top of
holder. To close, snap the AnoGotcha Holder
shut. Fig. 5
Note: It is easier to open and close the Gotcha by
starting at one end and working your way down the
holder. With large or curling graphics, it may be
easier to insert graphic at one end and slide into
holder from one end to another
Step 6
Suspend poster. Fig. 6
Important note:
Please save and reuse the AnoGotcha Holder, End
Caps and MultiClips for future projects.