ROSE DISPLAYS ANOGOTCHA ROUND WITH CABLE CLIP AND BALL... User manual

Parts
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should snap
into place. Fig. 2
Note: For OneUp Application place
the Cable Clip in the center of the
AnoGotcha Holder.
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into rail
by pushing on the clip. Fig. 4
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do not
pull on, or push against, the ball chain as
this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). To close, snap the
AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
OneUp Instruction Sheet
AnoGotcha™
Instructions for Hanging
Incept-7.4.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Figure 2
End Caps
06-5525
Cable Clips
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Ball Chains
96-0302P

Parts
Step 1
Insert T-Top Gotcha Holder into AnoGotcha
Shell. Fig. 1
Step 2
Insert single ball of ball chain into inner
channel of Cable Clip. The cable should snap
into place. Fig. 2
Note: For OneUp Application place
the Cable Clip in the center of the
AnoGotcha Holder.
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into rail
by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do not
pull on, or push against, the ball chain as
this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and insert
poster (top and bottom). To close, snap the
AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Instructions for Hanging
Incept-7.4.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
OneUp Instruction Sheet
AnoGotcha™
End Caps
06-5525
Cable Clips
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Ball Chains
96-0302P

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Insert single ball of the ball chain into inner
channel of Cable Clip. The cable should
snap into place. Fig. 2
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into rail
by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do not
pull on, or push against, the ball chain as
this will cause it to bind in the channel.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Instructions for Hanging
Incept-7.4.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipBallChain
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Instruction Sheet
AnoGotcha™
35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
End Caps
06-5525
Cable Clip
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Ball Chain
96-0302P

Parts
Step 1
Insert T-Top Gotcha Holder into
AnoGotcha Shell. Fig. 1
Step 2
Insert single ball of the ball chain into
inner channel of Cable Clip. The cable
should snap into place. Fig. 2
Step 3
Align one round end of cable clip with top
channel of the aluminum rail and insert.
Once in place, insert end of ball chain into
channel. Then press down on the other
round end of the cable clip and slide into
rail by pushing on the clip. Fig. 3
Note: Be sure to slide the ball chain into
place by pushing on the cable clip. Do
not pull on, or push against, the ball
chain as this will cause it to bind in the
channel.
Step 4
Push end caps into place. Fig. 4
Step 5
Snap the AnoGotcha Holder open and
insert poster (top and bottom). To close,
snap the AnoGotcha Holder shut. Fig. 5
Step 6
Suspend poster. Fig. 6
Instructions for Hanging
Incept-7.4.02
AnoQuick™ and AnoGotcha™are trademarks and Gotcha®is a registered
trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales
agent may be held liable for injury, loss or damage resulting from the use
of these products. Part #02INSAnoGotchaCableClipBallChain
End Caps
06-5525
Cable Clip
06-5050
T-Top Gotcha
12GT100
AnoGotcha Shell
12AG400
Figure 1
Figure 3 Figure 4
Figure 5 Figure 6
Figure 2
Instruction Sheet
AnoGotcha™
Ball Chain
96-0302P