ROSE DISPLAYS SUPERSNAP WITH ANOCONNECTORS User manual

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Step 1
Slide MultiClip into top of the
SuperSnap. Holding clip at a slight
angle, first insert one round end,
then press down on other round
end and push MultiClip into
position. Fig. 1 & 2
Note: Position MultiClip about
halfway down each SuperSnap. Fig. 3
Step 2
Insert AnoConnector into rail of one
SuperSnap. Make sure tabs face
upward. The side with one tab must
go in first. Fig. 4
Step 3
Insert threaded rod halfway into clip
rail of the same SuperSnap. Fig. 5
Step 4
Push the second piece of SuperSnap
onto both AnoConnector and the
threaded rod. Push together until
both holders meet. Fig. 6 Repeat
steps 2-4 for additional SuperSnaps.
Instructions for assembly
Incept-9.12.02
The SuperSnap and AnoConnector are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnector
Figure 6
Figure 3
AnoConnector
06-2930
Multi Clips
1UP-0100
SuperSnap
12S300
SuperSnap™ with AnoConnector Instruction Sheet
Figure 1 Figure 2
Figure 4
Figure 5
Page 1 of 2
6” Rod
97-0304-06

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
(continued)
Step 5
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close the
SuperSnap by starting at one
end and working your way down
the holder.
Step 6
Insert graphic into one section of
SuperSnap (top and bottom). Fig. 8
Step 7
To close, snap the SuperSnap shut.
Fig. 9
Step 8
You should now have one graphic in
place. Repeat steps 5-7 for hanging
additional graphics.
Step 9
Push end caps into place. Fig 10
Step 10
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps, AnoConnectors,
and MultiClips for future projects.
Instructions for assembly
Incept-9.12.02
The SuperSnap and AnoConnector are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnector
AnoConnector
06-2930
Multi Clips
1UP-0100
SuperSnap
12S300
SuperSnap™ with AnoConnector Instruction Sheet
Page 2 of 2
Finished Look
Open all holders
6” Rod
97-0304-06
Figure 8Figure 7
Figure 10Figure 9Insert posters

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
Step 1
Slide MultiClip into top of the
SuperSnap. Holding clip at a slight
angle, first insert one round end,
then press down on other round
end and push MultiClip into
position. Fig. 1 & 2
Note: Position MultiClip about
halfway down each SuperSnap. Fig. 3
Step 2
Insert AnoConnector into rail of one
SuperSnap. Make sure tabs face
upward. The side with one tab must
go in first. Fig. 4
Step 3
Insert threaded rod halfway into clip
rail of the same SuperSnap. Fig. 5
Step 4
Push the second piece of SuperSnap
onto both AnoConnector and the
threaded rod. Push together until
both holders meet. Fig. 6 Repeat
steps 2-4 for additional SuperSnaps.
Instructions for assembly
Incept-9.12.02
The SuperSnap and AnoConnector are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnector
Figure 6
Figure 3
AnoConnector
06-2930
Multi Clips
1UP-0100
SuperSnap
12S300
SuperSnap™ with AnoConnector Instruction Sheet
Figure 1 Figure 2
Figure 4
Figure 5
Page 1 of 2
6” Rod
97-0304-06

35 Congress Street, Salem, MA 01970
Tel# [phone] Fax# [phone]
e-mail:[e-mail]
Parts
(continued)
Step 5
Snap all sections of the SuperSnap
open. Fig. 7
Note: It is easier to open and close the
SuperSnap by starting at one
end and working your way down
the holder.
Step 6
Insert graphic into one section of
SuperSnap (top and bottom). Fig. 8
Step 7
To close, snap the SuperSnap shut.
Fig. 9
Step 8
You should now have one graphic in
place. Repeat steps 5-7 for hanging
additional graphics.
Step 9
Push end caps into place. Fig 10
Step 10
Suspend holders. Finished Look
Important note:
Please save and reuse the
SuperSnap, End Caps, AnoConnectors
and MultiClips for future projects.
Instructions for assembly
Incept-9.12.02
The SuperSnap and AnoConnector are trademarks of Rose Displays, Ltd.
Neither the manufacturer nor any sales agent may be held liable for
injury, loss or damage resulting from the use of these products.
Part #02INSSuperSnapAnoConnector
AnoConnector
06-2930
Multi Clips
1UP-0100
SuperSnap
12S300
SuperSnap™ with AnoConnector Instruction Sheet
Page 2 of 2
Finished Look
Open all holders
6” Rod
97-0304-06
Figure 8Figure 7
Figure 10Figure 9Insert posters