Rosen Aviation 0700-104 User manual

Document Number 105478 Rev F
ELECTRONIC REVISION
CONTROLLED

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 2 of 38
Technical Manual, Remote Display System
© 2011–2014 by Rosen Aviation, LLC
All Rights Reserved
The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written authorization from Rosen Aviation, LLC,
except as allowed under copyright laws.
Disclaimer of Liability
The information contained in this document is subject to change without notice. Because we are
continuously improving and adding features to our products, Rosen Aviation, LLC reserves the right
to change specifications without prior notice. Rosen Aviation, LLC shall not be liable for technical or
editorial errors or omissions contained herein.
Rosen Aviation, LLC
1020 Owen Loop South
Eugene, OR 97402
541.342.3802
888.668.4955
Fax: [phone]
www.rosenaviation.com

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 3 of 38
Contents
1. INTRODUCTION.................................................................................................................5
1.1. System Overview..........................................................................................................5
1.2. System Components.....................................................................................................6
1.2.1. Remote Inputs .................................................................................................................. 6
2. VIDEO INPUTS...................................................................................................................6
3. INSTALLATION GUIDELINES ...........................................................................................7
3.1. Mounting Configurations...............................................................................................7
3.1.1. Bulkhead Mounting Requirements.................................................................................... 7
4. ASSEMBLY INSTRUCTIONS FOR ACCESSORIES.........................................................8
4.1. Mounting Cosmetic Backs to a Bulkhead .....................................................................8
4.2. Attaching an RDM to a Cosmetic Back.........................................................................9
4.3. Mounting a Bezel........................................................................................................10
5. SYSTEM CONNECTIONS................................................................................................10
5.1. Pinout Connections.....................................................................................................11
6. RS-232 AND RS-485 CONTROL INPUTS........................................................................11
7. INITIAL POWER UP .........................................................................................................12
8. IR REMOTE CONTROL....................................................................................................13
9. OSD MENU OPTIONS......................................................................................................14
9.1. Exit..............................................................................................................................14
9.2. User Menu ..................................................................................................................15
9.2.1. Backlight......................................................................................................................... 15
9.2.2. Aspect Ratio................................................................................................................... 15
9.2.3. Scheme .......................................................................................................................... 16
9.2.4. Source............................................................................................................................ 16
9.2.5. Auto Adjust..................................................................................................................... 17
9.3. Image Adjust...............................................................................................................17
9.3.1. Scheme .......................................................................................................................... 17
9.3.2. Picture-Quality Controls.................................................................................................. 17
9.3.3. Reset Scheme................................................................................................................ 18
9.3.4. Image Adjust Advanced (Submenu) ............................................................................... 18
9.4. Info..............................................................................................................................21
10. TECHNICIAN MENU.......................................................................................................22
10.1. Advanced Technician Menu......................................................................................23
10.1.1. Factory Reset ............................................................................................................... 23
10.1.2. Viewing Angle............................................................................................................... 23
10.1.3. Comp/RGB 1 ................................................................................................................ 24
10.1.4. Comp/RGB 2 ................................................................................................................ 24
10.1.5. 3D Comb Filter ............................................................................................................. 24

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 4 of 38
10.1.6. Composite Sig (Signal) ................................................................................................. 24
10.1.7. AGC (Automatic Gain Control)...................................................................................... 24
10.1.8. RJ45 Cable Compensation........................................................................................... 25
10.2. Mode Menu...............................................................................................................25
10.2.1. Power Mode ................................................................................................................. 25
10.2.2. Operation Mode............................................................................................................ 26
10.2.3. SDI Overscan ............................................................................................................... 27
10.2.4. SDI Overscan %........................................................................................................... 27
10.3. OSD Timeout............................................................................................................28
10.4. Network ID................................................................................................................28
10.5. Splash Screen ..........................................................................................................28
10.6. Source Mode ............................................................................................................29
10.6.1. Momentary Mode.......................................................................................................... 29
10.6.2. Constant Mode ............................................................................................................. 30
11. TECHNICAL REFERENCES AND SUPPORT...............................................................31
11.1. Troubleshooting........................................................................................................31
11.2. Cleaning the Display.................................................................................................32
11.3. RTCA DO-160F Qualifications for Displays ..............................................................32
11.3.1. Other Certification Considerations for RDMs ................................................................ 34
11.4. Supported Video Specifications................................................................................34
11.4.1. DVI/HDMI Graphic Resolutions..................................................................................... 34
11.4.2. DVI/HDMI Standard Resolutions................................................................................... 35
11.4.3. VGA Resolutions .......................................................................................................... 35
11.4.4. YPbPr/Component Resolutions .................................................................................... 35
11.4.5. CVBS/Composite Resolutions ...................................................................................... 35
11.4.6. SDI Resolutions............................................................................................................ 36
12. DEFINITIONS..................................................................................................................36
13. REVISION HISTORY ......................................................................................................38

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 5 of 38
1. INTRODUCTION
Rosen’s Remote Display System consists of an ultra-thin remote display module (RDM) and a
high-definition (HD) remote electronics box. The remote electronics design provides more
mounting flexibility because the video processing electronics box can be located up to 50 feet from
the display. The high-definition display modules are available in a range of screen sizes and the
mounting options allow customers to configure a system that fits their aircraft’s cabin interior.
This manual provides general instructions about how to install all bulkhead configurations of the
Remote Display System onto your aircraft. It contains everything you need to know to wire the
components and confirm that the system is functioning correctly.
Note: Only trained and qualified personnel should perform installation and service.
1.1. System Overview
The Remote Monitor Electronics Box (RMEB) takes a video signal from various sources and
converts it to a serial format for distribution to a high-definition display. The RMEB operates one
Remote Display Module (RDM)—the RMEB 0700-107 Mod 02 is the latest model, which
replaces the RMEB 0700-104, and it operates all RDM sizes currently available from Rosen.
Figure 1 RMEB and RDM functional diagram
Control Input
Wired RS-232 Control
Wired RS-485 Control
Wired Remote IR Receiver
Graphic Signal Input
2x Composite video
2x 3G HD-SDI
2x DVI-I
- for DVI/HDMI w/ HDCP
- for VGA graphics
- for Component video
Remote
Monitor
Electronics
Box
(RMEB)
Power Output
Monitor RS-232
Serialized Video
Output
Power Input
28VDC only
Remote Display Module (RDM)
Status Output & 5V

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 6 of 38
1.2. System Components
To learn more about the following Remote Display System components and to access the
technical drawings, visit our website at www.rosenaviation.com.
Remote Monitor Electronics Box (RMEB)
RMEB (P/N 0700-104) operates 19-, 24-, 26-, and 32-inch RDMs
RMEB (P/N 0700-107 Mod 01) operates 19 through 42-inch RDMs
RMEB (P/N 0700-107 Mod 02) operates 19 through 55-inch RDMs
Remote Display Modules (RDM)
Mounting accessories: front bezel, cosmetic back, and credenza
Connector kits (sold separately) –see the technical drawings for specific P/Ns
For more information about a remote display system, please contact Rosen Sales or
Technical Support at 541.342.3802.
1.2.1. Remote Inputs
The RMEB provides 5V @100mA output to power an external IR receiver. The remote
monitors do not have a built-in IR sensor. The following options (sold separately) enable
remote inputs with the Remote Display System and adjust the on-screen display settings:
HD Monitor IR Kit (P/N 0500-023)
Universal remote control (contact Rosen Sales for P/N availability)
Alternatively, you can control the unit via a cabin management system using RS-485 or
RS-232. For a copy of the RS-232 External Controller Message Formats
(P/N 9002934) or RS485 Network Message Definitions document (P/N 9002933), please
contact Rosen Aviation Technical Support at 541.342.3802.
Note: For directions on operating the optional universal remote control, refer to the user’s
guide enclosed with the remote.
2. VIDEO INPUTS
The Rosen Remote Display System enables viewers to watch high-definition video as well as
standard-definition video. The remote electronics box supplies the following video inputs.
Two 3G HD-SDI inputs
Two Composite (CVBS)
Two DVI inputs (HDMI)
RGB & Component (YPbPr) - through the DVI connectors only
Accepts inputs up to 1080p, VGA-WUXGA
The RMEB connects to 28VDC aircraft power and receives video through a video distribution
amplifier or directly from video sources.

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 7 of 38
3. INSTALLATION GUIDELINES
3.1. Mounting Configurations
Rosen’s RDMs can be flush mounted, mounted with a sleek bezel (semi-proud), or proud-
mounted between a bezel and cosmetic back. The photos below are representative of the
different bulkhead mounting options for the remote displays. Please contact Rosen Sales for
specific configurations.
Figure 2 Bulkhead mounting options for remote display modules
Flush mount –RDM only
Semi-proud mount –RDM with bezel
Proud mount –RDM with bezel and a cosmetic back
3.1.1. Bulkhead Mounting Requirements
The RMEB and RDMs do not require any external forced-air cooling.
A flush mounted RDM can mount from the back, through an interior wall, or from the front
mounting tabs. Proud-mounted RDMs must attach from the front into the cosmetic back.
Technical drawings are available on the Rosen website at www.rosenaviation.com to
assist in the installation process. Pay close attention to the dimensions when considering
installation requirements. Dimensions for some models may vary, so be sure to consult
the latest drawings.
Touching the LCD with excessive force may leave pressure spots
that show in video display. Handle with care.
Flush mount
Semi-proud mount
Proud mount
Cosmetic back
Front bezel
RDM

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 8 of 38
4. ASSEMBLY INSTRUCTIONS FOR ACCESSORIES
This section provides instructions about how to assemble the cosmetic backs and bezels. To add
a stylish, proud-mount option, mount the cosmetic back to the bulkhead, attach the RDM to the
cosmetic back, and then snap on the bezel.
Note: Protect cosmetic and sensitive components from scratches, nicks, and debris during
hardware installation.
4.1. Mounting Cosmetic Backs to a Bulkhead
The cosmetic backs use two styles of mounting brackets depending on the size of RDM that you
install. The cosmetic backs are a universal fit—there is no top or bottom.
Technical drawings for the Remote Display System accessories are available on the Rosen
website at www.rosenaviation.com.
Attach the 19”, 22”, 24”, and 26” cosmetic back to the bulkhead using the four mounting brackets
and a minimum of four FHP screws (customer supplied) in the .188 mounting holes, as shown
below.
Figure 3 1901-, 2401-, 2201-, and 2601-800 cosmetic back mounting tabs
Attach to
bulkhead
Attach to
RDM

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 9 of 38
Attach the 32” cosmetic back to the bulkhead using six #6 100FHP screws
(customer supplied).
Attach the 42” cosmetic back to the bulkhead using ten #6 100FHP screws
(customer supplied).
Attach the 55” cosmetic back to the bulkhead using twelve #6 100FHP screws
(customer supplied).
Figure 4 3201-, 4201-, and 5501-800 cosmetic back mounting bracket
4.2. Attaching an RDM to a Cosmetic Back
Figure 5 shows an exploded view of a proud-mount assembly. Align the tabs on the RDM with the
mounting brackets on the cosmetic back. Secure with two 4-40 fasteners in each tab/bracket. The
number of mounting brackets varies by RDM size. For more dimensional information, see the
technical drawings for your specific assembly.
Figure 5 RDM with a proud-mount bezel assembly
Attach to
bulkhead
Attach to
RDM
Mounting brackets
on the cosmetic
back

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 10 of 38
4.3. Mounting a Bezel
Mount the cosmetic back and monitor before attaching the bezel. To attach a bezel to an RDM,
align the mounting bosses with the monitor standoffs and gently press on the retaining clips to
snap the bezel into place.
Bezels attach around the perimeter of the RDMs with retention fasteners. The quantity and type
of bezel fasteners varies depending on the size of the bezel and RDM. Figure 6 shows the
different assembled retention fasteners on the bezels. See the 55” Bezel Drawing (P/N 5501-
900) for assembly instructions.
Figure 6 Different bezel retention fasteners
5. SYSTEM CONNECTIONS
The RDM receives power, control, and serialized video from the RMEB located up to 50 feet away,
as shown below. The RMEB outputs a serialized video signal via an RJ-45 cable from P4 and
provides conditioned power and control to the RDM via a harness with DA15 connectors from P3.
To obtain information about interconnect cables, please contact Rosen Aviation’s Technical
Support at 541.434.4512 and request the Interconnect Cable Specification for Remote Electronics
(P/N 105821).
Figure 7 Remote display system connections
Ball stud
receivers on
32”–55” ”
bezels
Only wire
retaining clips on
19”–26” bezels
Top and
bottom
wire clips

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 11 of 38
5.1. Pinout Connections
There are several ways to connect the remote display system to an aircraft’s entertainment
system.
Follow the pinout descriptions on the technical drawings to assist in completing the wiring
connections. Use the pinout information in the RS-485 Configuration Discretes table on the
technical drawing (P/N 0700-107-CD) when operating in Auto SDI mode.
Note: This display is for entertainment purposes only; connect to a non-critical power bus.
6. RS-232 AND RS-485 CONTROL INPUTS
Inputs that control the RDMs can come from an IR or via a cabin management system using
RS-232 or RS-485. The RMEB accepts the following commands:
Table 1 RS-485 and RS-232 commands
Control
Description
Power ON
Turn the display on
Power OFF
Turn the display off
Source Composite 1
Select composite 1 video input
Source Composite 2
Select composite 2 video input
Source HD-SDI 1
Select HD-SDI 1 video input
Source HD-SDI 2
Select HD-SDI 2 video input
Source VGA 1
Select analog VGA 1 video input
Source VGA 2
Select analog VGA 2 video input
Source DVI 1
Select DVI 1 video input
Source DVI 2
Select DVI 2 video input
Source YPbPr 1
Select YPbPr 1 component video input
Source YPbPr 2
Select YPbPr 2 component video input
Ping Address
(RS-485 only)
Used by master device to detect all devices attached to the network
Exit
Exit the menu
OK/Enter
Selects active option when OSD is active

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 12 of 38
7. INITIAL POWER UP
Make sure that power is turned off and connect the following harnesses to the RMEB connectors:
1. Ensure low impedance ground connections on the RMEB housing and monitor
chassis grounding lugs.
2. Connect an external IR control or RS-232/RS-485 communication harness to P1.
3. Connect 28VDC power to P2.
Verify that the circuit breakers being used with the RMEB meet the power
requirements for the display size as stated in the RMEB technical drawing. Also,
avoid coiling the power wire as this can cause heat to build up in the wire. If you have
more questions about Power Requirements, contact Rosen Aviation’s Technical
Support at 541.434.4512.
4. Attach a DA15 interconnect cable to the RDM’s DA15 pigtail and connect to P3.
5. Attach an RJ-45 interconnect cable to the RDM’s RJ-45 pigtail and connect to P4. We
recommend grounding and strain relieving the harnesses on the RJ-45 connectors
using the brackets provided.
6. Connect the available video inputs.
7. Apply power and wait for a signal on the RDM. The default setting for the RMEB is
Auto On and the default source is SDI 1.
Do not plug or unplug the display connector while power is
applied.
Removing power while the OSD is open could result in a factory
reset.
When cycling power, leave unit off for 20 seconds before restoring
power.

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 13 of 38
8. IR REMOTE CONTROL
The remote display system uses a remote control to adjust the on-screen display (OSD) settings.
The instructions in this manual use the RC5 IR remote in describing how to navigate the OSD.
Table 2 shows the RC5 IR remote layout and the button descriptions.
Table 2 RC5 IR remote control
Note: The AUTO button works
only when an RGB source is
active. The MUTE and
VOLUME ± buttons are not
used.
How it Works
SOURCE
Switches between any enabled video inputs. Press the SOURCE
button twice to switch inputs. The first command sent will only display
the current source name in the upper-left corner of the monitor; the
second command switches the source.
POWER
Turns the display system’s power on and off.
MENU
Opens the Main Menu to access other settings and fine-tune the
display’s picture quality. For details, see Section 9, OSD MENU
OPTIONS, on page 14.
EXIT
Closes the OSD and saves settings. Exit does not close control bars.
ENTER
Accepts changes to menu settings. Selects menu options, accepts
settings, and closes the control bars.
◄►▲▼
Controls the navigation in the on-screen display menus. Navigate
between the OSD menu pages, options, and change settings.
ASPECT
Changes the aspect ratio or proportions of the picture depending on
the video signal. Switches between Full Screen, Pillar Box, and
Letterbox Expanded. See also Section 9.2.2, Aspect Ratio, on
page 15.
INFO
Opens the Info page on the OSD. Use INFO to review operating
status, verify details about the display, and access the Technician
Menu.
AUTO
(RGB only) Performs an auto-adjust function without a menu. Forces
the display to evaluate the RGB signals and ensure it is interpreting
them correctly. See also Section 9.2.5, Auto Adjust, on page 17.
BRIGHT ±
Opens the Backlight control bar. See also Section 9.2.1, Backlight, on
page 15.

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 14 of 38
9. OSD MENU OPTIONS
The OSD contains screen settings and options in menus and informational readouts that display
over the image, as shown below. Press MENU on the remote to open the Main Menu, as shown in
Section 9.1. Press the ▲▼ buttons to navigate within the menu pages. Press the ►◄ buttons to
navigate between the menu page, options, and values columns. Select the Back option to switch
menu pages. The yellow highlighted area shows the currently selected option in the menu.
Figure 8 OSD menu pages
The available menu options will vary depending on which source signal is active.
Press MENU to choose a setting or an option.
Select the Back option to switch menu pages.
Press EXIT to close the OSD and save settings.
Note: The on-screen display will timeout and close automatically after no screen activity for a
preset amount of time, which is adjustable on the Technician MenuOSD Timeout option. See
Section 10.3, OSD Timeout on page 28.
9.1. Exit
Use Exit to close the OSD. When you press MENU on the remote, the OSD opens to this
screen, as shown below. Press MENU again to close the OSD from this screen.
Press the ▲▼ buttons to access the other menu pages in the OSD.
From other settings within the OSD, press EXIT on the remote control to close the OSD.
Figure 9 Opening screen for the Main Menu
Press ►to access
the menu page
options
Press ►to access
the menu option
values
Press ▼to
access menu
pages; the
yellow highlight
shows which
menu is active.

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 15 of 38
9.2. User Menu
The Main Menu opens to the screen, shown in Figure 9 (above). Press the ►button to access
the User menu options.
Press ▼▲ buttons to select a User option and then press ENTER to change its value.
Figure 10 User menu page
9.2.1. Backlight
Use this setting to adjust the intensity of the LCD backlight.
From the User page, press the ►and ▼buttons to select Backlight and then press
ENTER to open the control bar shown below.
Press the ◄or the ► buttons to change the value on the control bar accordingly.
Press ENTER to set the backlight brightness and close the control bar.
Figure 11 Backlight option
9.2.2. Aspect Ratio
Use Aspect Ratio to adjust the picture expansion to match the encoding of the source
image most closely. Select UserAspect Ratio and then press ENTER. To switch the
display between aspect ratio modes (described below), press the ▲ ▼ buttons. Watch
for proportional changes in the background picture and choose the optimal mode for the
source. Press ENTER to set the mode and press EXIT to close the OSD.
To change the Aspect Ratio from the remote, press ASPECT.
Full Screen: Displays standard 4:3 source video in 16:9 aspect ratio by expanding the
image horizontally. Circles will appear as ovals in the central and outer portions of the
screen. If the source image is letterboxed, there will be black bars at the top and bottom
of the image. A 16:9 widescreen source will fill the screen with minimal distortion.
Pillar Box: A standard 4:3 source image will appear with vertical black bars on the left
and right side of the image. If the image source is letterboxed, then there will also be
horizontal bars at the top and bottom of the image as well.
Source and Auto
Adjust are only
available in
Standard Operation
Mode, and Auto
Adjust is active only
with a VGA (RGB)
source.

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 16 of 38
Letterbox Expanded: Expands the source video in the vertical and horizontal
dimensions to fill the display screen. Letterbox-format DVDs will have small or no bars
showing in this mode, while 4:3 aspect video sources will expand beyond the screen
boundaries and appear cropped.
Note: The Letterbox Expanded mode is not available for RGB or a graphic, PC-based
HDMI/DVI source.
9.2.3. Scheme
There are two default color settings or schemes: Natural and Vivid. If the screen colors
are not what you expect, select Scheme and press the ▲▼buttons to toggle between
the settings. The background picture’s colors change as you toggle between the settings.
Vivid uses a higher color saturation level above the Natural level.
Try both schemes to determine which one you like best before adjusting the other picture
quality settings.
Select UserScheme and then press ENTER to access the settings.
Select the setting and press ENTER to accept the changes, and then select Back and
press EXIT close the OSD.
9.2.4. Source
The Source page lists all of the available sources and shows which source is currently
selected.
Figure 12 User Sources
Select UserSource and press ENTER to access the settings.
To switch the source, press the ▲and ▼buttons.
Press ENTER to accept any changes, and press ◄to remain in the OSD or EXIT to
close the OSD.
To switch sources directly from the remote control, close the OSD and press the
SOURCE button twice for each input.

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 17 of 38
9.2.5. Auto Adjust
(RGB only) Use Auto Adjust when the RGB source is active to force the display to
evaluate the RGB signals and ensure that it is interpreting them correctly. To perform an
Auto Adjust within the OSD, select the option and press ENTER. (From the remote, close
the OSD and press the AUTO button.) The screen will briefly go black while the signals
adjust.
9.3. Image Adjust
Use the Image Adjust menu pages, as shown below, to control the color and picture quality.
Highlight Image Adjust and press the ►button to highlight the options, and then press ENTER
to change the option values.
Figure 13 Image Adjust menu options
9.3.1. Scheme
Scheme is also available from the Main MenuUser page. For information about how
this option works, see Section 9.2.3 on page 16. Changing the Scheme also affects
changes you make to the User menu settings and is source specific.
9.3.2. Picture-Quality Controls
The Brightness, Contrast, Saturation, Hue, and Sharpness menu options use control bars
to fine-tune different aspects of the picture quality. To adjust these options, press MENU
and the ▼arrow to select Image Adjust. Choose a menu option, and then press ENTER
to open a control bar and adjust the value, similar to Figure 14 shown below.
Press the ◄or the ► buttons to change the control bar’s value.
Press ENTER to set the intensity level and close the control bar.
Press EXIT to close the OSD.
Figure 14 Sample picture-quality control bar
Picture-
quality
controls

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 18 of 38
9.3.3. Reset Scheme
Restores the values of the current scheme to their default settings, and it affects only the
current source. Use Reset Scheme to revert to the default screen colors if the other
Image Adjust options did not correct the screen quality.
Select Image AdjustReset Scheme and then press ENTER.
Press EXIT to close the OSD.
For information about the different scheme modes, see Section 9.2.3 on page 16.
9.3.4. Image Adjust Advanced (Submenu)
Use the Image Adjust Advanced submenu options, as shown below, to fine-tune the
primary screen colors and to restore the display’s factory screen settings. Press the
MENU button and the ▼arrow to select Image AdjustAdvanced, and then press
ENTER to open the menu.
To close the menu, select the Back option and press ENTER, or press EXIT to close the
OSD.
Figure 15 Advanced submenu options
9.3.4.1. Color Temperature
Use the Color Temperature options to change the warmth of the picture in all
sources. When you select Color Temperature, the screen changes, and a toggle
appears to switch between User and 6500K, as shown below.
Figure 16 Color Temperature options
Select the User setting and then press ENTER.
Press ▼to access the individual colors.
}
RGB options
only

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 19 of 38
9.3.4.1.1. Color Levels: Red, Green, Blue
Setting the Color Temperature to User will make the Red, Blue, and Green options
active. Each color adjusts the low-level registers of its respective color value in the
picture.
Select the Image AdjustAdvancedColor Temperature and press ENTER.
Set Color Temperature to User, and then press ENTER.
Press the ▼ button to choose a color level and then press ENTER to open a
control bar to adjust the value, similar to Figure 17 shown below.
Red: Press the ◄ button to show more cyan-colored tones, and press the ►
button to intensify the red tones.
Green: Press the ◄ button to show more magenta tones, and press the ►
button to intensify the green tones.
Blue: Press the ◄ button to show more yellow tones, and press the ► button
to intensify the blue tones.
Press ENTER to set the color and close the control bar.
Press EXIT to close the OSD.
Figure 17 Sample color-level control bar
9.3.4.2. Restore Defaults
This option restores the default screen settings from the user menus for all video
sources. It does not erase Technician Menu settings or change the internal time and
date.
Select the Image AdjustAdvancedRestore Defaults options and then press
ENTER. A Defaults Restored message appears in the lower corner of the menu after
the restore is complete.
Figure 18 Restore Defaults option
}
RGB options
only
Status
message

Rosen Aviation Remote Display System
Document Number: 105478
Revision: F
Date: 06/23/14
Template: 4.4.1.6FM2; Revision A; 12/06/12
Page 20 of 38
9.3.4.3. Image Position Submenu
(RGB only) Use the Image Position options to center an RGB picture horizontally or
vertically on the screen. Note: Changing the resolution, source, or cycling power will
reset any adjustments to this submenu’s settings.
Select the Image AdjustAdvancedImage Position options and then press
ENTER.
Figure 19 Image Position option
9.3.4.3.1. Horizontal and Vertical Controls
(RGB only) From the Image AdjustAdvancedImage Position submenu, press
the ▼button to choose either Horizontal or Vertical,and then press ENTER to open
a control bar, similar to Figure 20 shown below.
Press the ◄ button to shift the picture left/up or the ►button to shift it to the
right/down.
Press ENTER to set the phase value and close the control bar.
Figure 20 Sample image positioning control bar
9.3.4.4. Auto Adjust
(RGB only) Use Auto Adjust when the RGB source is active to force the display to
evaluate the RGB signals and ensure that it is interpreting them correctly. To perform
an Auto Adjust within the OSD, select Image AdjustAdvanced submenu, press
the ▼button to choose Auto Adjust and press ENTER. (From the remote, close the
OSD and press the AUTO button.) The screen will go black briefly while the signals
adjust.