Rosen Aviation SlimLine 2002 Series User manual

Document Number: 9002645 Rev K
ELECTRONIC REVISION
CONTROLLED

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 2 of 34
Technical Manual, 20” SlimLine II Display
© 2008 by Rosen Aviation, LLC
All Rights Reserved
The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without written authorization from Rosen Aviation, LLC, except
as allowed under copyright laws.
Disclaimer of Liability
The information contained in this document is subject to change without notice. Because we are
continually improving and adding features to our products, Rosen Aviation, LLC reserves the right
to change specifications without prior notice. Rosen Aviation, LLC shall not be liable for technical or
editorial errors or omissions contained herein.
Rosen Aviation, LLC
1020 Owen Loop South
Eugene, OR 97402
541.342.3802
888.668.4955
Fax: [phone]
www.rosenaviation.com

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 3 of 34
Contents
1. INTRODUCTION AND DISPLAY OVERVIEW .................................................................5
1.1. Unpacking.................................................................................................................. 5
2. INSTALLATION GUIDELINES.........................................................................................5
2.1. Monitor Diagrams ...................................................................................................... 6
2.2. Cooling and Ventilation.............................................................................................. 6
2.3. Mounting Options....................................................................................................... 7
3. VIDEO CONNECTIONS....................................................................................................8
3.1. Main Interface Connector, 21W1 Male Combo D ...................................................... 9
3.2. S-Video Connector, 3W3 Male Coax Combo D....................................................... 10
3.3. DVI Input Connector................................................................................................ 10
4. TECHNICAL SETUP –TECHNICIAN ON-SCREEN DISPLAY......................................12
4.1. Enabling the On-Screen Display.............................................................................. 12
4.2. Menu Navigation...................................................................................................... 12
4.3. Main Menu Configuration......................................................................................... 13
4.3.1. Monitor Info .................................................................................................................. 13
4.3.2. Diagnostic Submenu .................................................................................................... 14
4.3.3. Advanced Menu ........................................................................................................... 16
4.3.4. Clearing Codes............................................................................................................. 24
4.3.5. Restore Defaults........................................................................................................... 25
5. OPERATION...................................................................................................................25
5.1. Front Switch Panel Features ................................................................................... 25
5.2. On-Screen Display Main Menu................................................................................ 27
5.3. Picture Submenu..................................................................................................... 27
5.4. OSD Submenu......................................................................................................... 28
5.5. Utility Submenu........................................................................................................ 28
5.6. Auto Submenu......................................................................................................... 28
5.7. Exit Submenu .......................................................................................................... 28
6. HOT KEYS......................................................................................................................28
7. RS-485 INFORMATION..................................................................................................29
7.1. Communication Protocol.......................................................................................... 29
7.2. Packet Format ......................................................................................................... 29
7.3. Packet Timing.......................................................................................................... 29
7.4. Wiring ...................................................................................................................... 30
7.5. Packet Format Description for 2002 Display Commands ........................................ 30
7.6. Network Setup/Ping Address................................................................................... 31

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 4 of 34
8. TECHNICAL REFERENCES AND SUPPORT...............................................................32
8.1. Technical Support.................................................................................................... 32
9. DO-180D QUALIFICATIONS..........................................................................................33
9.1. Specifications........................................................................................................... 34
10. REVISION HISTORY....................................................................................................34

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 5 of 34
1. INTRODUCTION AND DISPLAY OVERVIEW
This manual describes how to install the Rosen 20‖ SlimLine II Display onto your aircraft. It
contains everything you need to know to wire the display and confirm that it is functioning
correctly.
Note: Only trained and qualified personnel should perform installation and service.
1.1. Unpacking
Parts shipped with the 20‖ SlimLine II Display:
Outline & Installation drawing
20‖ SlimLine II Display
Main Interface connector kit (P/N 0300-025)
Optional controllers sold separately:
External 7-button Controller (P/N 0300-408)
Universal Color Remote (P/N 0500-015) shipped with Remote Controller Technical
Information (P/N 100434)
Optional connectors sold separately:
S-Video connector kit (P/N 0300-028)
DVI connector kit (P/N 0300-029)
For help with Outline & Installation drawings, please contact
Rosen Aviation Customer Service at [phone].
2. INSTALLATION GUIDELINES
There are several ways to connect the 20‖ SlimLine II Display to an aircraft’s entertainment
system.
Use the pinout descriptions on page 2 of the Outline & Installation drawing to assist in the wiring
process. Pay close attention to the pinout information while completing wiring connections.
Once you access the home page, click on ProductsDisplays20 In SlimLine. Select a
drawing by model number from the drop-down menu in the middle of the page.
Drawings are provided to assist in the installation process. Pay close attention to dimensions and
rotations when considering installation requirements.
Note: This display is for entertainment purposes only; connect to the non-critical power bus.
Touching the LCD with excessive force may leave pressure spots
that show in video display. Handle with care.

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 6 of 34
2.1. Monitor Diagrams
Figure 1 2002 outline dimensions (inches)
Figure 2 Side view dimensions (inches)
2.2. Cooling and Ventilation
The display is cooled by the flow of air, or natural convection. Special care must be taken with
the installation to provide a proper environment for air flow.
Monitor vents: The unit is designed with vent openings on the top, bottom, and rear
surfaces. The entire top vent, and either the entire bottom or entire rear vent must be

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 7 of 34
unobstructed for a minimum of one (1) inch. The vents must also be ducted to free
air.
Ducting: The installation must provide for an inlet duct (at bottom or rear), and an
exhaust duct at the top. Each of these ducts must have a minimum of four (4) square
inches of cross-sectional area.
Note: The display backlight will shut down if internal temperature reaches 140° F. It will not
come back on until the temperature drops 10 degrees below the threshold.
Note: Each mounting hole includes a 10-32 screw. To install the display, remove only the
screws that will be used to install the display. Do not remove the 4-40 flathead screws.
2.3. Mounting Options
Mounting options for this display are as follows:
Mount using all side mounting holes, or
Mount using all top and bottom mounting holes, or
Mount using all rear mounting holes
(Dimensions in inches)
Figure 3 Top view with mounting holes
Figure 4 Bottom view with mounting holes
1.61
2.34 6.75 13.50
1.19
2.34 13.50
1.61

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 8 of 34
Figure 5 Side view with mounting holes
Figure 6 Rear view with mounting holes
3. VIDEO CONNECTIONS
The three interface connectors for this display are:
21W1 Male Combo D-subminiature with 20 signal inputs for power, control, and IR
inputs, and one (1) shielded coaxial input for composite video
3W3 Male Combo D, Coax for S-Video input
DVI connector for analog RGB and DVI inputs
Warning!
!
Maximum screw penetration depth:
Top .75 inches
Bottom .75 inches
Sides .75 inches
Rear .50 inches

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 9 of 34
Mating connector kit included with purchase:
Rosen connector kit (P/N 0300-025)
Recommended additional mating connectors (optional)
S-Video connector kit, 3W3 Male Coax Combo D (P/N 0300-028)
DVI connector kit for analog RGB and DVI inputs (P/N 0300-029)
Note: The main connector backshell is chassis ground.
Warning! Do not plug or unplug display while power is applied!
3.1. Main Interface Connector, 21W1 Male Combo D
Pin #
Signal
Input/Output
Description
1
28V return
Input
Aircraft power supply
2
28VDC
Input
Aircraft power supply
3
IR +5V
Output
5V for IR receiver
4
IR signal
Input
Data from IR receiver
5
IR GND
Output
Ground for IR receiver
6
RGB/Video
Select (LVTTL)
Input
Source select switch input internally
pulled up to +3.3V –short to ground to
switch
7
Status output
(LVTTL)
Output
LVTTL level output (+3.3V) indicates
display is on when logic is high –
maximum current. (draw is 10
milliamps ,0V when display is off)
8
Power on/off
(LVTTL)
Input
Power toggle switch –internally pulled
up to +3.3V. Controls the on/off state of
the display.
9
RS-232 GND
N/A
Ground for serial control lines
10
28V RTN
Input
Aircraft power supply
11
28VDC
Input
Aircraft power supply
12
RS-232 RX
Input
Connects to serial switch/cabin
management (9600 baud)
13
RS-232 TX
Output
14
RS-485 (A out)
Output
RS-485 serial A out
15
RS-485 (B out)
Output
RS-485 serial B out
16
RS-485 (A in)
Input
RS-485 serial A in
17
RS-485 (B in)
Input
RS-485 serial B in
18
RS-485 GND
N/A
Ground for RS-485 lines
19
Reserved
Reserved
Reserved

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 10 of 34
Pin #
Signal
Input/Output
Description
20
Reserved
Reserved
Reserved
A1-signal
Composite
video
Input
Composite video input, 1 Vpp, 75 ohm
A1-shield
Composite
video return
Input
Shield for composite video
Shell
Chassis ground
3.2. S-Video Connector, 3W3 Male Coax Combo D
Pin #
Signal
Input/Output
Description
A1 Signal
S-Video
luminance
Input
S-Video luminance signal
A1 Shield
S-Video
luminance shield
Input
S-Video return
A2 Signal
S-Video
chrominance
Input
S-Video chrominance signal
A2 Shield
S-Video
chrominance
shield
Input
S-Video return
A3 Signal
Reserved
Reserved
Reserved
A3 Shield
Reserved
Reserved
Reserved
3.3. DVI Input Connector
Pin #
Signal
Input/Output
Description
1
T.M.D.S. Data2-
Input
Digital video serial channel 2 data
2
T.M.D.S. Data2+
Input
Digital video serial channel 2 data
3
T.M.D.S. Data2/4
shield
Input
Digital video serial channel 2 and 4
shield
4
T.M.D.S. Data4-
Input
Digital video serial channel 4 data
5
T.M.D.S. Data4+
Input
Digital video serial channel 4 data
6
DDC clock
Input
Display data channel clock signal
6
1
7
17
C1
C2
C3
C4
16
24

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 11 of 34
Pin #
Signal
Input/Output
Description
7
DDC data
Output
Display data channel data signal
8
Analog VSync
Input
Analog RGB VSync input 0-5V
9
T.M.D.S. data1-
Input
Digital video serial channel 1 data
10
T.M.D.S. data1+
Input
Digital video serial channel 1 data
11
T.M.D.S. data1/3
shield
Input
Digital video serial channel 1 and 3
shield
12
T.M.D.S. data3-
Input
Digital video serial channel 3 data
13
T.M.D.S. data3+
Input
Digital video serial channel 3 data
14
5V power
Input
5V power for display data circuit
15
GND for 5V,
HSync, VSync
Input
Ground for analog sync signals and 5V
power
16
Hot plug detect
Output
Indicates to source that display is
connected
17
T.M.D.S. data0-
Input
Digital video serial channel 0 data
18
T.M.D.S. data0+
Input
Digital video serial channel 0 data
19
T.M.D.S. data0/5
shield
Input
Digital video serial channel 0 and 5
shield
20
T.M.D.S. data5 -
Input
Digital video serial channel 5 data
21
T.M.D.S. data5+
Input
Digital video serial channel 5 data
22
T.M.D.S. clock
shield
Input
Shield for digital video serial clock signal
23
T.M.D.S. clock+
Input
Digital video serial channel clock signal
24
T.M.D.S. clock-
Input
Digital video serial channel clock signal
C1
Analog red
Input
Analog RGB red input, 0.7V, 75 ohm
C2
Analog green
Input
Analog RGB green input, 0.7V, 75 ohm
C3
Analog blue
Input
Analog RGB blue input, 0.7V, 75 ohm
C4
Analog HSync
Input
Analog RGB HSync input, 0-5V
C5
Analog Ground
Input
Analog RGB ground

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 12 of 34
4. TECHNICAL SETUP –TECHNICIAN ON-SCREEN DISPLAY
The display receives Composite, Analog RGB, S-Video, and Digital Video Input (DVI). DVI input
is shown as Digital RGB in the on-screen display when switching between video sources.
4.1. Enabling the On-Screen Display
To access the on-screen display (OSD) configuration for advanced settings, use the front-panel
keys or an IR remote to access the Technician Menu. On the front panel, press the following
button sequence:
◄, ►, ▲, ▼, ◄, ►, ▲, ▼, ▲, ▲, ▲, and then press Menu.
This sequence prevents passengers from accidentally accessing the configuration on-screen
display mode.
On-screen display will not function if the special filter is enabled.
To disable special filter, go to Section 5.5 Utility Submenu
4.2. Menu Navigation
Use the front-panel keys or an IR remote to move through menu selections. The current menu
screen title is always shown at the top of the screen.
Use up and down (▲▼) arrow keys to move the menu cursor to a different menu option
line.
Press the Menu key to select a menu option, or to accept an adjusted or changed menu
option.
Use left and right arrow keys (◄►) to adjust or change menu options.
Menu selections that have a submenu option have >> shown at the right side of the
menu option line.
Menu selections that return you to the previous menu have << shown at the right side of
the menu option line.
When > is shown at the left side of a menu option line, the cursor is on that line. This
does not mean that the menu option line is currently selected. A menu option line is
selected by pressing the Menu key.
Note: Most menus have help text at the bottom of the screen indicating which keys navigate
that menu.

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 13 of 34
4.3. Main Menu Configuration
Figure 7 Main Menu options
The Main Menu has a time-out setting that automatically returns the monitor to normal
operation if no keys are pressed for one (1) minute. The submenus do not have this time-out
setting.
To manually exit the Main Menu, move the cursor to the Exit OSD menu line and then press
the Menu key.
4.3.1. Monitor Info
Select the Monitor Info submenu to view information on the current status of the display.
The example below shows the Monitor Info submenu selection:
Figure 8 Monitor Info submenu
Main Menu
> Monitor Info >>
Diagnostics >>
Advanced Settings >>
Restore Defaults >>
Exit OSD >>
[UP] [DOWN] move cursor
[MENU] select option
firmware rev: rev A
CSOC rev: rev A
Total hrs: 115:53
Backlight hrs: 93
Composite: 82
ARGB: 3
S-video: 0
DVI: 8
Power Cycles: 145
Glitch Count: 4
Temp: 77F
< press any key to exit >

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 14 of 34
4.3.2. Diagnostic Submenu
Figure 9 Diagnostic submenu option
4.3.2.1. Self-test
Select the Self-test menu to initiate a test that determines and then displays the
status for some of the monitor’s internal components. This test runs automatically
when power is applied to the monitor, but it can be run manually from this menu
selection. A sample Self-test result is shown below.
Figure 10 Self-test submenu example
Diagnostic Menu
Self-test >>
Measure Comp Video
> Measure S-video
Measure RGB Red
Measure RGB Green
Measure RGB Blue
Input Scan >>
Main Menu <<
[UP] [DOWN] move cursor
[Menu] select option
eeprom access ok
RTC ram ok
RTC battery ok
temp sensor ok
< press any key to exit >
Self Test Result

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 15 of 34
4.3.2.2. Video Level Test
There are five tests for video signal levels:
Measure Composite Video
Measure S-Video
Measure RGB Red
Measure RGB Green
Measure RGB Blue
Each video level test measures the average voltage level of a particular video input
signal. Select the desired video signal to initiate a test. See below for a Video Level
Test result example.
Figure 11 Video Level Test result example
4.3.2.3. Input Scan
Select the input scan menu to initiate a short test that determines if the monitor can
detect any valid video input signals. The status of each input signal displays when
the test completes.
Note: Input scan tests are based on detecting the sync signals from each signal.
It is possible for a video signal to be physically connected to the monitor but still fail
this scan test if the voltage level is too high or too low.
Figure 12 Input Scan result example
RGB Green Level
Max 2.1
Avg 1.1
Min .2
< press any key to exit >
Scanning For Inputs
Composite Input found
S-Video not found
ARGB not found
DVI found
< press any key to exit >

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 16 of 34
4.3.3. Advanced Menu
The Advanced Menu is extensive. Use the following pages for guidance when
selecting Advanced Menu options and submenus.
Figure 13 Advanced Settings submenu options
4.3.3.1. Start-up Settings
Figure 14 Start-up Mode settings example
Start-up Mode
There are four settings available for the Start-up Mode:
Auto-on: The monitor always starts up in the ON state when 28V is applied. The
default mode is Auto-on.
Auto-off: The monitor always starts up in the STANDBY state when 28V is
applied.
Restore Last: The monitor returns to the previous power and video settings
after any power interruption.
Constant SW Mode: See ―Start-up Mode below.
Start-up Mode - Power On/Off Input Signal
The Power On/Off Input Signal pin (pin 8) can be used to control the Monitor’s On/Off
state. When Start-up Mode is set to Auto-on, Auto-off or Restore Defaults, the On/Off
Advanced Menu
> Start-up Settings >>
Clock Settings >>
Source Setup >>
Session Records >>
Network Settings >>
IR Settings >>
Main Menu <<
[UP] [DOWN] move cursor
[MENU] select option
Start-up Mode
Start-up Mode: auto-on
Glitch-time: 1.2
Splash Screen: "Rosen"
Membrane SW: enabled
> Load Default Settings
Exit -- save changes
Exit -- discard changes
[UP] [DOWN] move cursor
[MENU] select option

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 17 of 34
signal is activated by a momentary ground input. The monitor will toggle the On/Off
state in response to this momentary ground signal. When the Start-up Mode is set to
Constant SW, the power state is controlled directly by the voltage level on the pin. Zero
volts will turn the monitor Off, and 3V will turn it On. Note that when in Constant SW
Mode, the membrane switch, external controller and IR remote power buttons have no
effect.
Glitch-time
Glitch-time settings help control the monitor state when power is first applied in Auto-on
or Auto-off modes. For example, during a normal power-up sequence, when 28V power
has been off for several hours, the initial state of the monitor is set by the Start-up mode
selection. If 28V power is briefly interrupted while the monitor is on, the monitor will
respond by restoring the previous state and ignoring the Start-up mode setting. (One
example of a brief power interruption is when an aircraft switches from auxiliary power
unit (APU) to engine power.)
Note: The Glitch-time setting controls the length of time that the monitor uses to choose
between a normal power-up sequence and a power interruption sequence. The range
of this setting is from .5 seconds to 25.5 seconds, in increments of .1 seconds. The
default value is 1 second. The Glitch-time setting has no effect in ―Restore Last‖
Start-up mode.
Splash Screen
There are two splash screens available on this monitor; one is a solid blue background,
and the other is a white background with the Rosen Aviation Displays logo. The splash
screen appears for approximately 8 seconds when 28V power is first applied to the unit.
Use the Splash Screen menu option to choose the splash screen desired.
Front Panel Keys (Membrane SW)
The Front Panel Keys can be disabled for situations where the monitor is installed in a
bulkhead. If the possibility exists of the keys being inadvertently held in by the mounting
bezel in front of the monitor, select ―disabled‖ for this setting.
Note: Disabling Front Panel Keys only takes effect after the on-screen Main Menu
display is exited. While the on-screen display is active, the keys will still operate. Once
the keys become inoperable, you may still enter the technician sequence to access the
technical setup OSD.

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 18 of 34
Load Default Settings
Use this menu option to restore start-up settings to the factory configuration. This option
does not change other monitor settings. The factory start-up configuration is as follows:
Start-up mode = auto-on
Glitch-time = 1.0 seconds
Splash screen = Rosen Aviation Displays
Front Panel Keys = enabled
4.3.3.2. Clock Settings
This monitor contains a battery-backed real-time clock. The clock is set during
monitor production and should not need adjustment during the monitor’s life. If the
clock setting needs adjustment for any reason, access the Clock Menu to make
adjustments.
Figure 15 Clock settings example
Clock Menu
Year: 2004
Month: 06
Day: 03
Hour: 16
Minute: 00
> Exit -- save changes
Exit -- discard changes
________________________
[LEFT] [RIGHT] adjust
[UP] [DOWN] move cursor
[MENU] select option

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 19 of 34
4.3.3.3. Source Setup
Use the Source Setup menu selections to determine how the monitor selects video
sources. There are four modes available for selecting video sources:
Auto-Detect Mode
Constant Switch Mode
Momentary Switch Mode
Manual Mode
Figure 16 Source Mode Set-up menu
A line is shown between the brackets of the currently selected mode. Note that the
Manual Mode option has no other settings options, while the other three modes have
separate setup menus.
4.3.3.3.1. Auto-Detect Mode
Auto-Detect mode automatically switches the Video Source based on a priority
level assigned to each source. The priority levels are assigned, with level 1 being
the highest priority level and level 4 being the lowest level. The monitor always
displays the highest priority input that is available.
Note: To have a valid configuration, there must be unique sources assigned to
priority levels 1 and 2; levels 3 and 4 are optional.
For example, a typical configuration would be to have composite video as priority
2, and analog RGB as priority. This would cause the monitor to automatically
switch to the analog RGB input whenever a user attached a laptop computer to
the analog RGB input.
Source Mode Set-up
[] Auto-Detect Mode >>
[] Constant SW Mode >>
[] Momentary SW Mode >>
> [I] Manual Mode
Advanced Menu <<
[UP] [DOWN] move cursor
[MENU] select option
[I] indicates current mode

Rosen Aviation 20‖ SlimLine II Display
Document Number: 9002645
Revision: K
Date: 9/24/09
Template: 4.2-3-6-FM; Revision D; 13 March 2008 Page 20 of 34
Note: The menu will not allow an invalid configuration to be saved. If an invalid
setup is listed in the menu, the ―save‖ option is automatically replaced by an
―Invalid Setup!‖ warning.
Figure 17 Auto-Detect Mode submenu example
4.3.3.3.2. Constant Switch Mode
Constant Switch mode selects one of two video sources based on the state of a
single pole switch connected between ground and the select switch input pin (pin
6 on the 21W1 main interface connector). You can select any of the available
sources for the two switch conditions.
When the select switch pin is connected to ground, the monitor switches to the
video source indicated in the ―Switch Closed‖ menu setting. When the select
switch pin is open (not connected to ground), the monitor selects the video source
indicated in the ―Switch Open‖ menu setting.
Note: The two sources selected must be different to be considered a valid
configuration. The menu will not allow you to save an invalid configuration.
Figure 18 Constant Switch Mode submenu example
Auto-Detect Setup
Priority 1: ARGB
Priority 2: COMPOSITE
Priority 3: -
Priority 4: -
> Exit -- save changes
Exit -- discard changes
_____________________
[UP] [DOWN] move cursor
[RIGHT] adjust
[MENU] select option
Constant Mode Setup
> Switch Low: ARGB
Switch Hi: COMPOSITE
Exit -- save changes
Exit -- discard changes
_____________________
[UP] [DOWN] move cursor
[RIGHT] adjust
[MENU] select option