Rosen Aviation 4KS Series User manual

Document Number 111728 Rev A
Electronic Revision
Controlled

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 2 of 19
Technical Manual, 4K UHD Displays
© 2021 by Rosen Aviation, LLC
All Rights Reserved
The information contained herein is proprietary to Rosen Aviation, LLC. No part of this publication
may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any
language in any form by any means without the written authorization from Rosen Aviation, LLC,
except as allowed under copyright laws.
Rosen Aviation, LLC
1020 Owen Loop South
Eugene, OR 97402
541.342.3802
888.668.4955
Fax: [phone]
www.rosenaviation.com

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 3 of 19
Contents
1. INTRODUCTION.................................................................................................................4
1.1. System Overview..........................................................................................................4
Control Options................................................................................................................. 4
Mating Connectors............................................................................................................ 4
2. LRU LIST............................................................................................................................4
3. INSTALLATION GUIDELINES...........................................................................................5
3.1. Mounting Configurations...............................................Error! Bookmark not defined.
3.2. Cooling and Ventilation.................................................................................................5
3.3. Electrical Requirements................................................................................................5
3.4. Inputs and Connections................................................................................................5
3.5. Pinout Connections.......................................................................................................5
SDI Connectors (J7 and J8) Pin-out Logic and Function.... Error! Bookmark not defined.
Power Connector (J1) Pin-out Logic and Function............................................................ 6
I/O (J2) Pin-out Logic and Function .................................................................................. 6
Ethernet Connector (J3) Pin-out Logic and Function......................................................... 7
USB (J4) Pin-out Logic and Function................................................................................ 8
HDMI (J5) Pin-out Logic and Function.............................................................................. 9
Fiber optic (J6) Pin-out Logic and Function..................................................................... 10
Ethernet Strapping.......................................................................................................... 11
3.6. 4K Display Suggested Installation ..............................................................................11
Pre-installation................................................................................................................ 12
Installation...................................................................................................................... 12
4. INITIAL POWER UP .........................................................................................................12
4.1. Troubleshooting..........................................................................................................13
4.2. Cleaning the Display...................................................................................................15
4.3. RTCA DO-160G Qualifications for Displays................................................................15
4.4. Supported Video Specifications..................................................................................18
3G-SDI Resolutions........................................................................................................ 18
3G-SDI 4K UHD Resolutions.......................................................................................... 18
HDMI resolutions............................................................................................................ 18
5. DEFINITIONS....................................................................................................................18
6. REVISION HISTORY ........................................................................................................19

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 4 of 19
1. INTRODUCTION
This manual provides installation guidance and references to all technical information required to
install, service and maintain the Rosen 4K UHD Displays.
1.1. System Overview
The Rosen 4K Displays offer an all-in-one design which allows several installation options. Each
display can be installed in flush mount and semi-proud orientations. The displays also
accommodate a variety of input signals, resolutions and control capabilities allowing installation
versatility.
Control Options
⚫External IR receiver
⚫RS232
⚫Ethernet
⚫USB
⚫WIFI (if equipped)
Please see interface control document P/N 111727
Mating Connectors
Recommended mating connectors are listed on the 4K Display Outline and Installation
Drawings.
2. LRU LIST
Table 1 Smart Display LRU List
Monitor Model Number
4KS240-002
4KS320-004
4KS430-002
4KS480-001
4KS550-001

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 5 of 19
3. INSTALLATION GUIDELINES
3.1. Cooling and Ventilation
For venting requirements see Outline and Installation drawings.
3.2. Electrical Requirements
⚫Operational Voltage Range 18 to 32VDC (DC models)
⚫Operational Voltage Range 97 to 134 VAC 360 to 800 HZ (AC models)
For Max Current see Outline and Installation drawing for each display size.
3.3. Inputs and Connections
All Rosen Smart Displays use the following connections:
J1 J2 J3 J4 J5 J6 J7 J8 J9 J10
Figure 1 24" bulkhead display connections
1. Power (J1)
2. I/O (J2)
3. Wi-Fi (J3)
4. Ethernet/strapping (J4)
5. USB(J5)
6. SPDIF (J6)
7. HDMI (J7)
8. Fiber optic (J8)
9. SDI 1 (J9)
10. SDI 2 (J10)
11. SD Card (for future use)
3.4. Pinout Connections
There are several ways to connect the display to an aircraft’s entertainment system.
Reference these pinout descriptions for the Smart Display Modules to assist in completing the
wiring connections.
Note: This display is for entertainment purposes only; connect to a non-critical power bus.

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 6 of 19
Power Connector (J1) Pin-out Logic and Function
Table 2 Power Logic and Function for DC monitors
Pin
Signal
Input/output
Description
A1
PRIMARY 28VDC
Input
Aircraft power supply
A2
PRIMARY RETURN
Input
Aircraft power supply
A3
SECONDARY 28VDC
Input
Aircraft power supply
A4
SECONDARY RETURN
Input
Aircraft power supply
A5
Chassis
Chassis ground
Table 3 Power Logic and Function for AC monitors
Pin
Signal
Input/output
Description
A1
Line 115 VAC
Input
Aircraft power supply
A2
Earth (chassis)
Input
Aircraft power supply
A3
Neutral 115 VAC
Input
Aircraft power supply
I/O (J2) Pin-out Logic and Function
Table 4 I/O Logic and Function
Pin
Signal
Input/output
Description
1
RESERVED
Reserved
Reserved
2
RESERVED
Reserved
Reserved
3
RESERVED
Reserved
Reserved
4
Signal GND
Output
Audio line out
5
Audio left
Output
Audio line out
6
Audio Right
Output
Audio line out
7
Audio mute control
Input
audio control
8
Select control
input
Video control
9
IR +5V
Output
5 volts out
10
SIGNAL GND
11
RESERVED-Debug
Reserved
Reserved
12
IR in
input
IR signal input
13
Debug RS232 TX
Output
RS232 Debug
14
Debug RS232 RX
Input
RS232 Debug
15
Discrete out3
Output
Reserved

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 7 of 19
Wi-Fi Connector (J3) Pin-out Logic and Function
Table 5 Wi-Fi Logic and Function
Pin
Signal
Input/output
Description
Center
Wi-Fi
Input
Wi-Fi input
Outer
Return
Input
Wi-Fi input
No Wi-Fi on the 4KS320-004 monitor
Ethernet Connector (J4) Pin-out Logic and Function
Table 6 Ethernet Logic and Function
Pin
Signal
Input/output
Description
1
ENET A+ (TX+)
Input/output
Gigabit Ethernet capable.
TX+ for fast Ethernet (100baseT).
2
ENET A- (TX-)
Input/output
Gigabit Ethernet capable.
TX- for fast Ethernet (100baseT).
3
ENET B+ (RX+)
Input/output
Gigabit Ethernet capable.
RX+ for fast Ethernet (100baseT).
4
ENET B- (RX-)
Input/output
Gigabit Ethernet capable.
RX- for fast Ethernet (100baseT).
5
ENET C+
Input/output
Gigabit Ethernet capable.
6
ENET C-
Input/output
Gigabit Ethernet capable.
7
ENET D+
Input/output
Gigabit Ethernet capable.
8
ENET D-
Input/output
Gigabit Ethernet capable.
9
Gb ENET Ctrl in
Input
Open = 100baseT, Ground = Gigabit
10
ETH_ADDR_0
Input
This pin is used to set the IP address. See
Ethernet Strapping for more information.
11
ETH_ADDR_1
Input
This pin is used to set the IP address. See
Ethernet Strapping for more information.
12
ETH_ADDR_2
Input
This pin is used to set the IP address. See
Ethernet Strapping for more information.
13
ETH_ADDR_3
Input
This pin is used to set the IP address. See
Ethernet Strapping for more information.
14
ETH_ADDR_4
Input
This pin is used to set the IP address. See
Ethernet Strapping for more information.
15
ETH_ADDR_5
Input
This pin is used to set the IP address. See
Ethernet Strapping for more information.
16
Pwr Control In
Input
Open= off, Ground = on
17
SDI CTRL in
Input
Open = fiber, Ground = Copper
18
SIGNAL GND
Typical return for strapping
19
SIGNAL GND
Typical return for Ethernet strapping

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 8 of 19
Pin
Signal
Input/output
Description
20
RESERVED
Reserved
Reserved
21
RESERVED
Reserved
Reserved
22
RESERVED
Reserved
Reserved
23
RESERVED
Reserved
Reserved
24
RESERVED
Reserved
Reserved
25
RESERVED
Reserved
Reserved
26
USB-A OTG ID
Input
Open = USB Debug, Ground = USB
normal use
USB (J5) Pin-out Logic and Function
Table 7 USB Logic and Function
Pin
Signal
Input/output
Description
1
VBUS
Output
+5 volt Power
2
USB D-
Input/output
USB 2.0 Data-
3
USB D+
Input/output
USB 2.0 Data+
4
GND
Ground
5
SSRX-
Input
Super speed receiver
6
SSRX+
Input
Super speed receiver
7
GND
Ground
8
SSTX-
Output
Super speed Transmitter
9
SSTX+
Output
Super speed Transmitter
SPDIF Out (J6) Pin-out Logic and Function
Table 8 USB Logic and Function
Pin
Signal
Input/output
Description
Center
SPDIF
Output
SPDIF Audio Output
Outer
SPDIF Return
Output
SPDIF Audio Output

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 9 of 19
HDMI (J7) Pin-out Logic and Function
Table 9 USB Logic and Function
Pin
Signal
Input/output
Description
1
TMDS Data2+
Input
2
TMDS Data2 Shield
3
TMDS Data2−
Input
4
TMDS Data1+
Input
5
TMDS Data1 Shield
6
TMDS Data1−
Input
7
TMDS Data0+
Input
8
TMDS Data0 Shield
9
TMDS Data0−
Input
10
TMDS Clock+
Input
11
TMDS Clock Shield
12
TMDS Clock−
Input
13
CEC
Input/output
14
Reserved
15
SCL
Input
I²C serial clock for DDC
16
SDA
Input/output
I²C serial data for DDC
17
Ground
Ground
18
+5 V
Input
Power
19
Hot Plug Detect
Output

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 10 of
19
Fiber optic (J8) Pin-out Logic and Function
Table 10 Fiber Optic Logic and Function
Pin
Signal
Input/output
Description
1
Ethernet 1 RX
Input
RX for Ethernet 1
2
SDI-1
Input
SDI video input 1
3
Ethernet 2 RX
Input
RX for Ethernet 2
4
SDI-2
Input
SDI video input 2
5
RESERVED
Reserved
Reserved
6
RESERVED
Reserved
Reserved
7
RESERVED
Reserved
Reserved
8
RESERVED
Reserved
Reserved
9
RESERVED
Reserved
Reserved
10
Ethernet 2 TX
Output
TX for Ethernet 2
11
Reserved
Reserved
12
Ethernet 1 TX
Output
TX for Ethernet 1
SDI Connectors (J9 and J10) Pin-out Logic and Function
Table 11 SDI Logic and Function
Pin
Signal
Input/output
Description
Center
3G-SDI
Input
SDI video input
Outer
3G-SDI Return
Input
SDI video input

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 11 of
19
Ethernet Strapping
Setting the IP Address Mode in the Technician Settings to a static IP address will enable
Ethernet Strapping.
The table below describes the Ethernet pinout configuration for the 4K Display when the
IP Address Mode is set to 10.0.0.100. The table shows the first eight entries, but the
addressing range uses all 5 pins for a total of 64 addresses
Reference the 4K Display Outline and Installation Drawing for the pin locations in the
Ethernet & strapping connector.
Table 12
4K Display
Ethernet
StrappingIP
Address
Ethernet Address Pins
Logic
5
4
3
2
1
0
10.0.0.100
0
0
0
0
0
0
0=GND
1=OPEN
10.0.0.101
0
0
0
0
0
1
0=GND
1=OPEN
10.0.0.102
0
0
0
0
1
0
0=GND
1=OPEN
10.0.0.103
0
0
0
0
1
1
0=GND
1=OPEN
10.0.0.104
0
0
0
1
0
0
0=GND
1=OPEN
10.0.0.105
0
0
0
1
0
1
0=GND
1=OPEN
10.0.0.106
0
0
0
1
1
0
0=GND
1=OPEN
10.0.0.107
0
0
0
1
1
1
0=GND
1=OPEN

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 12 of
19
Pre-installation
⚫All required Rosen products are complete and available.
⚫Aircraft geometry as well as fastener locations have been manufactured within the
tolerances defined in the Rosen Outline and Installation drawings.
Installation
The Following equipment is necessary to complete the installation.
Note: Installation assumes Aircraft interior has been designed and fabricated using
mating dimensions provided on the Outline and Installation drawing.
⚫Customer supplied fasteners
⚫Tooling required for customer supplied aircraft hardware installation
For part details see Outline and Installation drawing.
3.5. Software upgrade
The 4K displays support field upgrade via Ethernet/USB which is detailed in P/N 110231 or
111727.
4. INITIAL POWER UP
Make sure that power is turned off and perform the following steps.
1. Ensure a low impedance ground connection on the chassis from the ground lug
bosses indicated on the Outline and Installation drawing(optional).
2. Connect the power supply and video source to the appropriate connectors.
3. Supply power and wait for a video signal on the screen. The primary input is SDI
Do not plug or unplug the display connector while power is
applied.
When cycling power, leave unit off for 20 seconds before restoring
power.

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 13 of
19
4.1. OSD MAIN MENU
Video Settings
Reset video settings: use to reset to factory settings
Aspect Ratio: the Following are available
1 Normal - scale the video image horizontally to fit the width of the screen
2 Full screen- scale video horizontally & Vertically until input image fills the screen
3 Pillar box - create vertical bars on the right and left of the displayed image
4 Stretch - stretch the video image to fit the height and width of the screen
Contrast: Adjust picture contrast
Pix Brightness: Adjust picture brightness
Saturation: Adjust picture Saturation
Backlight: Adjust Backlight brightness
Hue: Adjust picture Hue

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 14 of
19
About Device: Gives user Information about the monitor
Reboot: Reboots the device so you don’t need to pull power
Legal and regulatory: FCC info and rules
Technical settings
To protect the display from accidental or unintentional adjustments, the Technical Menu
is accessible only with a special button combination. Changes made in the Technical
Menu will take effect immediately, with the exception of Power Modes and IP settings.
Power mode changes will take effect when the OSD is exited. IP Settings will take effect
when the unit is rebooted.
To access the Technical Menu use the remote and quickly input the following with the
arrow keys:
▲▼▲▼▲▲▲
The Technical Menu will pop up below the Legal & Regulatory. The following can be
adjusted in the Technical Menu.
Remote Control Number: This allows you to change the remote ID 1-4 for use with
Rosen’s programmable remote.
Power Mode: Allows you to modify how power input pin 16 of the J4 connector is used.
The following are available: Auto on, Auto off, Ground on, Open on, or Momentary.
Mute Mode: Allows you to modify how audio is muted from input pin 7 of the J2 connector
is used. The following are available: Ground on, Open on, or Momentary on
Reset all setting: This will reset everything to the default mode.
Video Over scan: This is for over scanning of SDI video, the default is 25 which is 2.5%
Device Alias: This allows you to name your device. This helps when multiple devices are
on the same network.
Launcher Wallpaper: Selects a Wallpaper. Supported wallpaper formats: BMP JPEG, GIF, and
PNG
Select Boot Animation: Selects the animation shown during the boot process. Supports the
Android-style .zip format
IP Address Mode: Choose between DHCP or specify a static IP address to use as the
base of a range that takes strapping pins into account
Set Gateway IP Address: Lets you change the gateway IP Address.
Set Netmask IP Address: Lets you change the Netmask IP Address.
Set DNS IP Address: Lets you change the DNS IP Address.
Source Mode: Allows you to modify how Video is selected from input pin 8 of the J2
connector is used. The following are available: auto and Manual.
Note: when in manual mode the IR function like the select in pin every momentary/source
press cycle to the next enabled source.
EXT_HDMI: Allows you to enable/disable the source and prioritize if in auto mode
SDI 1: Allows you to enable/disable the source and prioritize if in auto mode

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 15 of
19
SDI 2: Allows you to enable/disable the source and prioritize if in auto mode
IMX8: this is the settings menu it cannot be disabled.
Wi-Fi : Allows you to enable/disable the Wi-Fi
Available Networks: Allows you to choose wi-fi network
5. UPLOADING USER CONTENT
User content consists of, Wallpaper and Animation Configure file structure below on USB
RosenConfigFiles
•Wallpapers (Supported wallpaper formats: BMP JPEG, GIF, and PNG)
•BootAnimations (Supports Android-style .zip formats)
Once the media files are appropriately organized, plug the USB drive into a monitor and follow on
screen instructions. Files can also be transferred via network update, contact Rosen Aviation for
additional information.
5.1. Troubleshooting
Table 13 Troubleshooting tips and solutions
Problem
Possible Solutions
Screen is black
⚫Verify the unit is receiving power.
⚫Verify the pinout is correct.
⚫Verify you are on the correct input
⚫Verify the Power Control In signal
5.2. Cleaning the Display
If glass surfaces become contaminated, surfaces may be cleaned by wiping with a microfiber
cloth. The cloth may be dampened (but not wet) with deionized water. Do not spray water
directly on the monitor or glass.
5.3. RTCA DO-160G Qualifications for Displays
The table below shows the DO-160G compliance of the 4K UHD Display, unless otherwise
noted. Omitted test sections/categories are not applicable to this product or its expected
installation.
Table 14 The 4K UHD display is compliant with the following DO-160G test categories

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 16 of
19
Description
Section
Category
Comments
Temperature and Altitude
4
Ground Survival/Short-Time Operating
Low Temp
4.5.1
A1
Operating Low Temperature
4.5.2
A1
Ground Survival/Short-Time Operating
High Temp
4.5.3
A1
Operating High Temperature
4.5.4
A1
In-Flight Loss of Cooling
4.5.5
–
Not Applicable
Altitude
4.6.1
A1
+17,000ft
Decompression
4.6.2
A1
Not Applicable
Overpressure
4.6.3
A1
Not Applicable
Temperature Variation
5
Temperature Variation
5.3.1
C
-15°C to +55°C
Humidity
6
Standard Humidity
6.3.1
A
Operational Shocks & Crash Safety
7
Operational Shocks
7.2.2
B
Crash Safety (Impulse)
7.3.2
B
Crash Safety (Sustained): Fixed-Wing
Transport Aircraft, Random Orientation
(≥9g/direction)
7.3.3
B
Satisfies Inertial Loads
requirements per 14 CFR
§ 25.561(b)(3)
Vibration
8
Random Vibration –Fixed Wing Aircraft
8.5.2
S (Curve B)
Waterproofness
10
Y
Substantiation by
Company Testing
Fluids Susceptibility
11
Fluids Spray –Coffee, OJ, Cola, Cleaning
Solvent (for all), Wine (for 32” and 43”
only)
11.4.1
F
Fungus Resistance
13
F
Substantiation by Analysis
Magnetic Effect
15
Magnetic Effect
15.3
B
Deflection Distance: D <
300 cm
Power Input (DC, Designation ZXI)
16
Normal Operating Conditions (DC)
16.6.1
Average Value Voltage (DC)
16.6.1.1
Z
Ripple Voltage (DC)
16.6.1.2
Z
Momentary Power Interruptions (DC)
16.6.1.3
Z (A)
Normal Surge Voltage (DC)
16.6.1.4
Z

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 17 of
19
Description
Section
Category
Comments
Engine Starting Under Voltage Operation
(DC)
16.6.1.5
Z
Abnormal Operating Conditions
16.6.2
Voltage Steady State (DC)
16.6.2.1
Z
Low Voltage Conditions
16.6.2.2
–
Momentary Under Voltage (DC)
16.6.2.3
Z
Abnormal Surge Voltage (DC)
16.6.2.4
Z
Inrush Current
16.7.5
I
Voltage Spike
17
Voltage Spike
17.4
A
Audio Frequency Susceptibility
18
AF Conducted Susceptibility- Power
Inputs
18.3.1
Z
Induced Signal Susceptibility
19
Magnetic Fields Induced Into Equipment
19.3.1
AC
Electric Fields Induced into Equipment
19.3.2
–
Not applicable to
equipment with metal
enclosure
Magnetic Fields Induced Into
Interconnecting Cables
19.3.3
AC
Electric Fields Induced Into
Interconnecting Cables
19.3.4
AC
Spikes Induced Into Interconnecting
Cables
19.3.5
AC
Radio Frequency Susceptibility
20
Conducted Susceptibility (CS) –10 kHz to
400 MHz
20.4
T
Radiated Susceptibility (RS) –100 MHz to
8 GHz
20.5
T
Emission of Radio Frequency Energy
21
Conducted RF Emission –150 kHz –152
MHz
21.4
M
Radiated RF Emission –100 MHz –6
GHz
21.5
M
Electrostatic Discharge (ESD)
25
Electrostatic Discharge (ESD)
25.5
A
Flammability
26
–
Flammability compliance
per 14 CFR § 25.853

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 18 of
19
5.4. Supported Video Specifications
3G-SDI Resolutions
480i/29.97
576i/25
720p/50, 720p/59.94, 720p/60
1080i/25, 1080i/29.97, 1080i/30
1080p/23.97, 1080p/24, 1080p/25, 1080p/29.97, 1080p/30, 1080p/50, 1080p/59.94,
1080p/60
3G-SDI 4K UHD Resolutions
3840x2160/23.97, 3840x2160/24, 3840x2160/25, 3840x2160/29.97, 3840x2160/30,
3840x2160/50, 3840x2160/59.94, 3840x2160/60
HDMI resolutions
480i/29.97, 480i/30
576i/25
480p/59.94, 480p/60
576p/50
720p/50, 720p/59.94, 720p/60
1080i/25, 1080i/29.97, 1080i/30
1080p/23.97, 1080p/24, 1080p/25, 1080p/29.97, 1080p/30, 1080p/50, 1080p/59.94,
1080p/60
3840x2160/23.97, 3840x2160/24, 3840x2160/25, 3840x2160/29.97, 3840x2160/30,
3840x2160/50, 3840x2160/59.94, 3840x2160/60
OLED displays are susceptible to screen burn in. Do not Display a
static image.

Rosen Aviation 4K UHD Monitors
Document Number: 111728
Revision: A
Date: 10/14/21
Page 19 of
19
6. DEFINITIONS
3G-SDI
Newer, high-definition serial digital interface with a single 2.970 Gbit/s
serial link
LRU
Line Replaceable Unit
LCD
Liquid Crystal Display
P/N
Part Number
RS-232
Standard for serial data communication lines
VDC
Volts direct current
7. REVISION HISTORY
Revision E is limited to draft or prototype documents. Revisions I,
O, Q, S, X and Z are not to be used.
Revision
Date
Revision Description
EC
A
10/14/21
Initial release
21-0472