Rosen Aviation 42" User manual

42″HD Gas Plasma Display
Technical Manual
www.rosenaviation.com
Document Number 9002570, Rev A
FOR REFERENCE ONLY

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
1
Table of Contents
INTRODUCTION ................................................................................................................................................ 3
SAFETY.............................................................................................................................................................. 4
GENERAL SAFETY ............................................................................................................................................. 4
PHYSICAL SAFETY............................................................................................................................................. 4
ELECTROMAGNETIC COMPATIBILITY (EMC) ....................................................................................................... 4
DESIGN SAFETY ................................................................................................................................................ 4
GETTING STARTED.......................................................................................................................................... 5
UNPACKING ...................................................................................................................................................... 5
PRE-INSTALLATION............................................................................................................................................ 5
INSTALLATION AND CONNECTION ............................................................................................................... 6
INSTALLATION WARNINGS ................................................................................................................................. 6
OPERATOR INTERFACE CONNECTIONS ............................................................................................................... 7
DVI (DIGITAL VISUAL INTERFACE)...................................................................................................................... 8
ANALOG RGB INPUT (COMPUTER) .................................................................................................................... 8
ANALOG RGB USED AS COMPONENT VIDEO (YPRPB) ....................................................................................... 8
HDTV COMPONENT VIDEO (YPBPR.2) .............................................................................................................. 8
YPRPB.2 USED AS COMPUTER ANALOG RGB WITH SYNC ON GREEN................................................................. 8
S-VIDEO AND S-VIDEO.A................................................................................................................................... 9
COMPOSITE VIDEO ............................................................................................................................................ 9
STANDARD-INTERLACED TV (STV) COMPONENT VIDEO (YPBPR.1).................................................................... 9
COMPUTER CONTROL (RS-232) ........................................................................................................................9
INTERFACE OPTIONS ......................................................................................................................................... 9
INPUT POWER AND GROUND CONNECTIONS........................................................................................... 10
GROUND STUD CONNECTIONS ......................................................................................................................... 10
AC POWER CONNECTIONS .............................................................................................................................. 10
OPERATOR CONTROLS AND INDICATORS................................................................................................10
IR CODE SWITCH ............................................................................................................................................ 10
INFRARED REMOTE CONTROL .......................................................................................................................... 10
REMOTE INFRARED SENSOR ............................................................................................................................ 10
UNIT OPERATION ........................................................................................................................................... 11
REMOTE POWER ON/OFF ................................................................................................................................11
ON SCREEN DISPLAY (OSD) ...........................................................................................................................11
SOURCE SELECTION........................................................................................................................................ 11
IR UNIVERSAL REMOTE CONTROL DISCRETE COMMANDS (DIRECT IR).............................................................. 11
ANALOG RGB/DVI MODES ............................................................................................................................. 12
BASEBAND VIDEO MODES (COMPOSITE,COMPONENT,S-VIDEO)...................................................................... 12
FLEXISCREENTM SCALER................................................................................................................................. 12
Using the FlexiScreenTM Scaler................................................................................................................. 12
Display Aspect Ratio Selections................................................................................................................ 13
Source Aperture Selections....................................................................................................................... 13
PIP MODES..................................................................................................................................................... 14
PICTURE BY PICTURE ...................................................................................................................................... 15
SAVING SETTINGS ........................................................................................................................................... 15
BRIGHTNESS ADJUSTMENTS............................................................................................................................ 15
CONTRAST ADJUSTMENTS............................................................................................................................... 15
HUE ADJUSTMENTS......................................................................................................................................... 15
COLOR ADJUSTMENTS .................................................................................................................................... 15
DISPLAY SETUP .............................................................................................................................................. 15

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
2
Instant On .................................................................................................................................................. 16
OSD Background....................................................................................................................................... 16
Freeze........................................................................................................................................................ 16
Color Gamma ............................................................................................................................................ 16
Input Port Enable....................................................................................................................................... 16
Direct IR Setup .......................................................................................................................................... 16
CARE AND MAINTENANCE ........................................................................................................................... 17
SCREEN CLEANING ......................................................................................................................................... 17
AIR VENT CLEANING ....................................................................................................................................... 17
FUSES ............................................................................................................................................................ 17
RECOMMENDATION FOR SCREEN SAVER .......................................................................................................... 17
OPERATOR TROUBLESHOOTING....................................................................................................................... 18
SERVICE AND SUPPORT................................................................................................................................... 19
PACKAGING AND SHIPPING .............................................................................................................................. 19
APPENDIX A: PACKING FOR SHIPMENT..................................................................................................... 20
APPENDIX B: REMOTE CONTROL OPERATION OVERVIEW .................................................................... 22
APPENDIX C: OSD MENU STRUCTURE & COMMANDS ............................................................................ 30
APPENDIX D: CONFIGURATION AND PERFORMANCE OVERVIEW ........................................................ 38
SPECIFICATIONS.............................................................................................................................................. 38
USER INTERFACES .......................................................................................................................................... 38
PIP (MULTIPLE SCENARIO).............................................................................................................................. 38
REAL TIME DIGITAL SIGNAL PROCESSING ........................................................................................................ 38
ELECTRICAL AND ENVIRONMENTAL .................................................................................................................. 38
MECHANICAL .................................................................................................................................................. 39
APPENDIX E: DEFINITION OF TERMS.......................................................................................................... 40
WARRANTY EXCLUSIONS ............................................................................................................................ 41
OUTLINE DRAWINGS ..................................................................................................................................... 42

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
3
Introduction
Congratulations! You have purchased the world’s most advanced and highest resolution
42" HD gas plasma display with built-in motion adaptive line doubler/scalar and multiple
high definition television (HDTV) direct inputs. You have wisely invested by choosing to
use a digital plasma display. In addition, there are up to 8 video inputs and multiple
picture-in-picture (PIP) scenarios.
The picture quality of your gas plasma display system is the best in its class for analog or
digital video presentation. The images produced by this plasma display system are
stunning – providing movie-film clarity with very black blacks, very white whites, true-to-life
skin tones – and also giving a perception of looking through the screen, rather than at it.
There is no better match to DVD and HDTV systems.
This unit contains the most comprehensive image enhancement settings available for
plasma displays through an intuitive, user friendly on-screen display (OSD). The OSD can
be accessed by either the infrared universal remote control (IR) supplied with your system,
or by an RS-232 connection. The IR has single pushbutton direct access to source
selections, scalar control, PIP control, and power on/off.
In addition, the 42" HD gas plasma display’s digital video converter (DVC) incorporates an
advanced scalar that provides virtually unlimited zoom and pan capabilities. User
prescribed scalar presets are provided to allow quick and simple full-screen viewing with
common widescreen and anamorphic picture formats. The scalar incorporates motion-
adaptive processing to preserve picture focus and smooth movement over a wide range of
image conditions.
The HDTV-direct inputs incorporate proprietary adaptive component video conversion
interface:
Directly operates with 480i or 480p and up to 1080i
Operates with either bi-level or tri-level syncs
Operates with RGBHV VESA levels, including the Direct TV HD-DSS system
Wide signal level and offset adaptability
This manual emphasizes safety, to both the user and the equipment. This display,
although the lightest and thinnest in its class, is designed with ruggedness and capability
for high reliability. However, unless the user understands how the equipment is to be
handled and operated, full benefits of this system’s superior design and safety features
may not be realized. Please read this manual to fully understand the capabilities of the 42"
HD gas plasma display system.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
4
Safety
General Safety
Physical Safety
Electromagnetic Compatibility (EMC)
This Equipment has been designed to meet the requirements of F.C.C. part 15 and CE
Directive 89/336/EEC with applicable harmonized standard EN-55022. These
requirements are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy. Installation and Connection on page 6 of
this manual lists installation guidelines for the 42" HD gas plasma display to be FCC and
CE compliant. If this system is not installed and used in accordance with the instruction
manual, it may cause interference to radio communications.
Design Safety
This Equipment has been designed in accordance with the safety and material guidelines
set forth in CSA/UL 1950. Most of the materials are CSA/UL listed. The display has been
designed with a special glass front filter to minimize the risk of shattering, if broken. For
additional information on the safety verification status of this equipment, refer to Installation
and Connection (page 6).
Caution
To reduce the risk of electric shock, do not remove any covers
from the display. Refer servicing to an authorized distributor or
factory trained service technician.
Warning
To avoid the risk of fire and electric shock, do not expose
this product to corrosive environments including ocean
spray, rain, or moisture; do not allow water or other liquids
in the unit. Exposure to such environments can cause
serious damage to the unit that would not be covered under
warranty.
Caution
Use the three-prong AC power cord supplied with the unit
to ensure that proper ground connection is maintained. A
safety ground lug is also provided on the unit and should
be used in accordance with your local electrical code.
Failure to provide a proper ground from the installation’s
power source may result in injury to personnel and serious
damage to the unit that would not be covered under
warranty.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
5
Getting Started
Unpacking
Carefully remove all components of the display from the packaging. Place the display face
(glass side) down on a soft, flat surface for ease of installation.
Note: The original packaging materials should be kept in case of service or
relocation. Replacement packaging may be purchased from the factory.
When the 42" HD digital display is installed and operating properly, please
store this manual in a safe place for future reference.
Pre-installation
Figure 1 shows the pieces included with your new digital display. Please check the
equipment included in this shipment to confirm that the pieces shown are included. If they
are not, then please contact your dealer or distributor immediately.
Figure 1
Note: the IR remote control may be a different style than shown in Figure 1. Remote
control information is included in Appendix B on page 22.
Caution
Extreme caution should be taken when unpacking the digital monitor.
It has been designed for rugged use; however the display monitor
contains glass that could break if dropped. Appendix A (page 20)
shows how the 42" HD gas plasma display was packaged for
shipment. This will guide your efforts to unpack the system.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
6
Installation and Connection
Installation Warnings
The display unit shall be handled by at least two persons during installation and moving.
The display should be operated only when proper connection has been made to the
grounding stud provided on the unit.
Mounting the unit in any orientation with installer/user supplied mounting hardware is totally
the installer/user’s responsibility and liability.
Removal of the front bezel is strictly prohibited.
Exposure of the product to corrosive environments including ocean spray, rain or moisture,
or allowing water or other liquids to enter the unit shall void warranty.
Installation of the 42" HD gas plasma display into any aviation or mobile application must
be as specified in the applicable installation drawings. Any provided applicable addenda to
this manual for installation and/or maintenance must also be followed.
The display is cooled using air vents. Air vents must be open to free air in order to function
properly. The display must be installed with at least 1 inch of clearance above and below
the unit.
Failure to observe the safety configuration of the product and handle accordingly shall void
warranty.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
7
Operator Interface Connections
All operator connectors are located at the rear of the unit. Only one video source is
required for your new 42" HD gas plasma display. However, multiple video sources can be
connected at the same time.
Figure 2
Up to 8 Video Inputs:
INPUT CONNECTOR
TYPE
DESCRIPTION BANDWIDTH
DVI DVI 1.0 Computer Digital RGB Up to 60Hz 768p
RGB DVI 1.0/HDB15 Computer RGB or DTV/HDTV
Component
Up to 60Hz 768p
YPbPr 3 BNCs DTV/HDTV Component Up to 60Hz 768p or
30Hz 1080i
S-Video DIN4 NTSC/PAL Baseband Interlaced STV
S-Video A (*) DIN4 NTSC/PAL Baseband Interlaced STV
Composite (* and **) RCA NTSC/PAL Baseband Interlaced STV
Composite (* and **) RCA NTSC/PAL Baseband Interlaced STV
Composite (* and **) RCA NTSC/PAL Baseband Interlaced STV
NOTE: A Source cannot be selected from the OSD unless it has been enabled.
See Input Port Enable on page 16.
* With Video Bundle Accessory
** Three composite inputs can be replaced by one component input with interlaced STV bandwidth.
Note: When connecting a video source to the display unit, keep in mind that a higher quality cable will
result in better picture quality.
Ground Stud
Fuse Carrier
IR Code Switch
Video Bundle

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
8
DVI (Digital Visual Interface)
If your new display is being used with a computer with DVI output, connect a DVI cable to
this connector location and the other end to your computer. Your cable should not be
longer than necessary.
Analog RGB Input (Computer)
If your new display is being used with a computer that has only a VGA output, connect a
VGA cable with a DVI-Analog connector to this DVI/RGB connector location (see Figure 2
on page 7), and connect the other end to your computer’s VGA feature connector. Your
cable should not be longer than necessary.
Analog RGB Used as Component Video (YPrPb)
With the use of proper cabling as shown in Figure 3, the unit can also be set up to accept
HDTV component video (YPrPb) on the analog RGB input. Adjustments on the OSD are
also needed. Under Source Setup, HDTV Input should be turned ON and Color Space
should be changed to YUV HD. The remote control and OSD arrangements for this
configuration are described in more detail in Appendices B and C (pages 22 and 30).
Figure 3
HDTV Component Video (YPbPr.2)
If your new display is to be used with a video source that uses HDTV Component Video
interconnection, connect your BNC cables to the BNC connectors labeled Y, Pr, and Pb.
YPrPb.2 Used as Computer Analog RGB with Sync on Green
With the use of proper cabling as shown in Figure 4, the unit can also be set up to accept
computer analog RGB with sync on Green. Under Source Setup, HDTV Input should be
turned OFF and Color Space should be changed to RGB. The remote control and OSD
arrangements for this configuration are described in more detail in Appendices B and C
(pages 22 and 30).
Figure 4
3 Coax
to HDB15
Adapter Cable
HDB15 to DVI-A Adapter Connector
Plugged into Monitor
YPrPb
Source
3 Coax
from HDB15
Adapter Cable
BNC Connectors plugged into Monitor
Analog RGB Source
With HDB15 Connector
3 Coax
from HDB15
Adapter Cable
Anolog RGB Source
with HDB15 Connector
BNC Connectors Plugged into Monitor

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
9
S-Video and S-Video.A
If the display is to be used with a video source that uses the S-Video type of
interconnection, connect the 4-pin mini-DIN connector to this connector location, or to the
video bundle’s S-Video.A 4-pin mini-DIN connection (see video bundle in Figure 5). This
cable should not be longer than necessary.
Figure 5
Composite Video
NOTE: A Source cannot be selected from the OSD unless it has been enabled
and saved. See Input Port Enable on page 16.
If the display is to be used with a standard video source, connect a video quality cable with
a RCA connector via the video bundle to this connector location. An alternative is to
purchase a BNC to Phono (RCA) adapter and use a BNC cable between the video source
and the video bundle.
Note: There are up to 3 composite inputs available to the user via the video bundle.
If any of the composite inputs are used on the video bundle, then the
standard-interlaced TV (STV) component video input will be unavailable to
the user.
Standard-Interlaced TV (STV) Component Video (YPbPr.1)
If the display is to be used with a CAV video source, connect video quality cables with RCA
connectors via the video bundle to this source. An alternative is to purchase BNC to Phono
(RCA) adapters and use BNC cables between the video source and the video bundle.
Note: Y is connected to yellow, Pb is connected to white, and Pr is connected to red.
If the component inputs are used on the video bundle, then the STV
composite video inputs will be unavailable to the user.
Computer Control (RS-232)
This RJ45 connector is for advanced computer control without using the infrared remote
control. All of the remote functions are available through this connector with additional
controls available. Appendix B (page 22) provides full details on the RS-232 remote
control including the cable/connector details.
Interface Options
If your unit was ordered with certain interface options, these may be included as follows:
IR Out: This optional output provides wideband, universal remote control
repeater compatibility.
RF Antenna Input: Not Used.
12VDC Out: Output for certain add-on external options that require 12VDC.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
10
Input Power and Ground Connections
Ground Stud Connections
The back of the display has a ground stud that must be connected to an earth ground (see
Figure 2 on page 7). It is the installer’s responsibility to determine the local code for
materials and dimensional requirements for lug size, wire size, length and location of the
earth ground connections in the installation.
AC Power Connections
Place the power cord into the back of the unit. Do not connect the power to your wall plug
at this time.
Operator Controls and Indicators
IR Code Switch
On the back of the unit (see Figure 2 on page 7) is a switch labeled IR CODE that is
located between the video bundle input and IR output. It should be in the full down position
as set at the factory. The IR remote control supplied with your unit has been
preprogrammed to operate the OSD with the switch in this position. If you want to change
IR codes to avoid interference from other IR remote controls, you can select a different
switch setting and reprogram the IR to a different code set. See the information provided
with the IR remote control supplied with your unit for code-set and code-switch settings. For
additional information, refer to Appendix B on page 22.
Infrared Remote Control
The infrared remote control supplied with your new 42" HD gas plasma display is the main
user control for the system. It can access all the capabilities of your display. For full details
including the OSD, see Appendix B (page 22) and Appendix C (page 30). The summary
functions available via remote control are described in the following section on unit
operation.
Remote Infrared Sensor
The remote control infrared sensor is located on the front of the display. As you are looking
at the front of the display, the sensor is located in the lower right hand corner of the frame
as shown in Figure 6. You will obtain the best performance from the remote control if you
aim it at this sensor.
Caution
Ensure that the AC power cord is disconnected from the
AC power source before performing the following steps.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
11
Figure 6
Unit Operation
After the installation is complete, plug the main power cord into the specified voltage outlet.
The unit has been set up at the factory so that it will turn on in the standby mode.
Remote Power On/Off
The remote control has a function that will only enable and disable the display’s screen (for
example: standby mode). The unit will remain in the standby mode when the display
screen is disabled by remote control. In this mode, the fans will not operate, and the unit
will draw only a few watts of power. The unit can be enabled again by using the IR, or by
RS232 command.
On Screen Display (OSD)
Invoking the OSD will access the system controls, which are fully detailed in Appendix C
(page 30). The primary system control functions or modes are summarized in the following
paragraphs.
Source Selection
Source selection by the remote control, in most installations, will only have to be performed
one time. Once you select the source: Computer RGB (VGA), Composite.Y, Composite.R,
Composite.W, S-Video, S-Video.A, YPbPr.1, YPbPr.2, or DVI, the system will remember
your source and you will not have to re-select it.
If you are using more than one source for video, you will have to change between the
different sources. The unit will always remember your last video source selection when
enabled from standby. However, if the unit is powered down improperly (for example: AC
power is removed), then the video source selection last saved by RS232 or the OSD’s
SAVE selection will be remembered and shown on the screen at power-up.
IR Universal Remote Control Discrete Commands (Direct IR)
Regardless of which menu the user is viewing, pressing one of the discrete command
buttons on the IR causes a corresponding immediate action. These discrete command
buttons are detailed in Appendices B and C, and are set up at the factory as defaults.
However, they are programmable through OSD menus. The Direct IR Menu is accessible
IR Sensor

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
12
as factory default discrete command button 9. The user can immediately recall the
discrete command button assignments by pushing 9 on the IR.
Note: This assumes that the user has not changed this particular factory default.
Analog RGB/DVI Modes
Once the VGA/SVGA mode is invoked by selecting the VGA source, menu selections are
available for adjusting color, contrast, brightness and interface synchronization as well as
FlexiScreenTM control. After selecting a menu function, the OSD presents a bar and a
value for your reference while performing the adjustment or function control.
Baseband Video Modes (Composite, Component, S-Video)
When a baseband video mode is invoked by selecting one of the baseband video sources,
menu selections are available for adjusting color, contrast, brightness and interface
variables as well as FlexiScreenTM control. After selecting a menu function, the OSD
presents a bar and a value for your reference while performing the adjustment or function
control.
FlexiScreenTM Scaler
FlexiScreenTM controls image sizing and positioning on the display screen for each of the
sources provided.
Using the FlexiScreenTM Scaler
The goal of FlexiScreenTM is to enhance the viewing experience by allowing the user to
tailor the image to their liking. Factory preset formats of the more popular settings are
provided per source input. These format settings target a wide range of media formats
and allow the user to create their ideal image. Follow the quick and easy steps listed
below to customize the image using the FlexiScreenTM. The steps are organized as a
top-down approach; begin at the top of the list and work down. Any time the image
becomes satisfactory, abort the steps and exit the OSD menu with a save. Saving the
settings to memory will preserve the configuration for the future.
With the desired source input selected, bring up the FlexiScreen menu.
Choose a predefined source format that best fits the source image to the screen.
Verify the following:
The Display Aspect Ratio (“Disp Aspect”) setting fills the screen
appropriately.
The choices are arranged by popular film mastering formats.
The four remaining settings are the discrete parameters that make up the
actual source aperture used by the built-in scalar.
Height and width along with the horizontal and vertical offsets are provided to
allow the user ultimate control. See Figures 7 and 8 for more details.
Altering any of these four values causes the “Src:” description to read
“Custom”. This is provided to alert the user that the settings have been
altered from factory presets.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
13
Display Aspect Ratio Selections
“16:9“ will cause the image to fill the entire width of the display screen.
“4:3” will cause the image to only fill a portion of the display screen to achieve a 4:3
aspect ratio.
“1:1” (not shown below) will cause the image to fill the screen with a direct one for
one pixel association with the source aperture adjustments. For example, if you
chose a 600 width and a 400 height, then a 600 x 400 window should be visible on
the display screen.
“Panoramic” will cause the center of the screen to be displayed in a normal fashion
and the outside 10% of the image (left and right side only) will be stretched to fit the
full size of the screen.
Figure 7
Source Aperture Selections
Cycle through Source Aperture Selection choices to initialize the source aperture
adjustments listed below. These settings identify a particular group of source aperture
adjustments that have been optimized for the “widescreen” or “letterbox” type movies.
Each setting targets the minimization of black bars encoded on movie media, while
maintaining an inherent aspect ratio to diminish distortions. Choices are listed as film
mastering formats.
“Letterbox” Image
Shown 4:3
“Letterbox” Image Shown 16:9
With Reduced Source Aperture
to Minimized “Black Bars”
“Letterbox” Image Shown With
Panoramic View Shown
“Letterbox” Image
Shown 16:9

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
14
Source Aperture Adjustments
Although the Source Aperture Selection initializes the source aperture, the
FlexiScreenTM menu also includes provisions for manual adjustments. Height and
width along with the horizontal and vertical offsets are provided to allow the user
ultimate control. These settings define the boundaries of the active image showing
on the display. The source aperture can be thought of as a window overlay of the
source frame as shown in Figure 8. What is defined within this window makes up
the active image. The best application for these functions is to crop out the black
bars of a widescreen movie. There are associated source aperture adjustments for
each of the source aperture settings. Altering any of these four values causes the
“Src:” description to read “Custom”. This is provided to alert the user that the
settings have been altered from factory presets.
Figure 8
PIP Modes
Picture in Picture (PIP) is a feature that makes it very easy to view two different video
inputs at the same time. The main display can be showing any active input while the PIP
window can be activated to view another active input in many different combinations,
including the main display video source (see note on following page). Many different
combinations are referenced as “Multiple Scenario PIPs”. One example is that while
viewing the S-Video input programming, the PIP window can be set to view a HDTV input

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
15
program or vice versa. These programs can be swapped or toggled from one to the other
using the remote control system or the IR (remote control: factory default direct IR
command button 8).
Note: Figure 2 (page 7) indicates there are certain exclusions to the multiple
scenario PIPs. For example, 2 video inputs sharing the same switch cannot
be combined in a PIP scenario. Also note that the Flexiscreen settings do not
affect PIP widow images in that the format delivered at the switch input will
be displayed in the PIP window. Therefore, letterbox and widescreen formats
will be displayed as such in PIP, although Flexiscreen factors will be applied
to corresponding inputs on the main display.
Picture by Picture
This is a special PIP mode in which the main picture is shown on the left side of the screen
and the PIP is shown on the right side. This mode is offered to provide an unobstructed
view of the main picture while a PIP is activated.
Saving Settings
If any settings have been changed, you can store the new settings so that the unit will
default to these new settings automatically. This can be performed individually for each
source. If you change any settings, and do not save them, the 42" HD gas plasma display
will revert to the most recently saved settings when the unit is turned off.
Brightness Adjustments
The picture brightness is factory set to the middle of the range. This is normally
satisfactory for most viewing. However you may want to adjust it for your specific
conditions. If the brightness is turned up very high, a washout condition might appear. If
this happens, simply decrease the brightness of the display. The OSD shows a bar and a
value for reference while adjusting.
Contrast Adjustments
The picture contrast is factory set to the middle of the range. This is normally satisfactory
for most viewing. However, you may want to adjust it for your specific conditions. The
OSD shows a bar and a value for reference while adjusting.
Hue Adjustments
The picture hue is factory set to provide the most accurate color reproduction. This is
normally satisfactory for most viewing. However you may want to adjust it for your specific
conditions. The OSD shows a bar and a value for reference while adjusting.
Color Adjustments
The picture color is factory set to give true color representations. This is normally
satisfactory for most viewing. However you may want to adjust it for your specific
conditions. The OSD shows a bar and a value for reference while adjusting.
Display Setup
The display unit has many options that can be changed from the factory default to the user
preferences. The display setup options are detailed on the following page.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
16
Instant On
This setup option enables the display to turn on and show video as soon as the power
is applied to the unit. If set to OFF, this option keeps the unit in the standby mode until
the user enables the display via the IR remote or the RS232 control.
OSD Background
When enabled, the OSD will have a solid background. If disabled, the OSD will not
have a distinctive background.
Freeze
This function enables you to freeze the image currently on the screen. Please note that
this function does not pause or stop the video source, only the screen.
Color Gamma
Within the Display Setup menu is the Color Gamma adjustments. In normal situations
this menu should not have to be used. However, if conditions or situations require an
adjustment to the color gamma curves, this can be accomplished in this sub menu. See
Appendix C (page 30) for full details.
Input Port Enable
This setup menu is very important while the unit is being installed (use in conjunction
with Operator Interface Connections, beginning on page 7). The installer is required to
turn on or off the unit’s various inputs. This menu, once set, should normally not require
further modifications after unit installation is complete. This Menu is a SMART menu in
that it will not allow conflicting inputs to be enabled. You must save the settings once
they have been set for the installation. A source cannot be selected from the
OSD unless it has been enabled and saved.
Direct IR Setup
Direct IR Setup menu is provided so that the user can customize the way the IR
controls the 42" HD gas plasma display with discrete commands. See Appendix B
(page 22) for full details.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
17
Care and Maintenance
Screen Cleaning
The screen can be cleaned using a very mild glass cleaner that is non-abrasive, and a lens
grade tissue for optical surfaces. Do not spray the glass cleaner directly onto the glass.
Spray the glass cleaner onto the tissue, and then clean the glass.
Air Vent Cleaning
All air vents of the display should be inspected periodically for buildup of dust or other
obstructions. Such obstructions can interfere with the proper cooling of the unit causing
reduced performance and reliability. Air vent obstructions can be removed by vacuuming
around the air vents.
Fuses
The unit uses ONLY a 5 x 20mm, 5 Amp, 250V time-delay type fuse with a 1500 Amp
interrupting rating such as Littlefuse® 215005 or equivalent. Replace fuse with same type
and rating only. The fuse is located in a snap-in carrier below the input power receptacle.
See Figure 2 (page 7).
Recommendation for Screen Saver
The plasma display panel in the unit incorporates phosphors. These phosphors could be
damaged by prolonged display of still pictures and/or text. Therefore a screen saver
program should be employed in still picture applications. Such applications especially
include computer graphics. However, we often forget that some video sources such as
DVD players can also put up menus and still pictures and/or text. Therefore, protect
against these situations also.
Caution
Do not allow water or other liquids to enter the unit. This can cause
serious damage to the unit that would be very costly to repair.
Always be sure that the AC power is turned off during cleaning.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
18
Operator Troubleshooting
Category Symptom Check
Unit does not come on
1. Input power cord connections
2. Rear line fuse
3. Power source
Unit comes on but display
does not light or have
O.S.D.
1. Batteries in remote
2. Remote power on
Remote does not work or
unit will not turn on with
infrared remote control
1. Replace infrared remote control batteries
with new, good batteries and reprogram the
remote
2. Ensure that the infrared sensor on the
display is not blocked
Power
Display turns on with
O.S.D. but does not show
video
1. Enable and save the video input per Input
Port Enable on page 16.
2. Video source
3. Video cables from the video source to the
unit
4. Source selection for the display with the
remote control (Refer to Remote Control
commands)
System doesn’t remember
changed settings
1. No settings are saved until SAVE is
manually selected from within the menu. If
settings are changed and not saved, the
next power up will return the unit to it’s
previously saved parameters.
Picture seems distorted:
circles are not round—
video or RGB modes
1. This is usually caused by selecting modes in
the FlexiScreen menu that don’t maintain
pixel correlation; Select Standard or 4:3
mode to confirm
Picture is too dark or too
light
1. O.S.D. for Brightness control
2. Source for poor quality
Picture has too much or
not enough contrast
1. O.S.D. for Contrast control
2. Source for poor quality
Picture is too high on
screen 1. O.S.D. and remote control for position
Picture is too low on
screen 1. O.S.D. and remote control for position
Picture is too far to the left
of the screen 1. O.S.D. and remote control for position
Picture is too far to the
right of the screen 1. O.S.D. and remote control for position
Picture does not have the
correct height 1. O.S.D. and remote control for correct height
All Modes
Picture does not have the
correct width 1. O.S.D. and remote control for correct width
Video Modes Pictures are too green or
purple 1. HUE in O.S.D.

42” HD Gas Plasma Display Rosen Aviation Displays, LLC
19
Category Symptom Check
Screen does not sync up
1. Input settings for the computer. They should
be one of the acceptable display rates listed
in Appendix D (page 38)
Blue is dim or too bright 1. O.S.D. Blue Gain Adjustment
Green is dim or too bright 1. O.S.D. Green Gain Adjustment
DVI, Analog
RGB Mode
Red is dim or too bright 1. O.S.D. Red Gain Adjustment
No sync and appearance
has mixed up colors or
black and white
1. O.S.D. for PAL or NTSC format, match with
source format
Composite
Video, S video
and YPbPr.1
Picture appears to be
Black and white
1. Source connection
2. Source to interface cable and connections
3. Color in O.S.D.
4. Source might be Black and White
The picture appears black
and white
1. Cables from the source for proper
connections, for example, y to y
2. Color in O.S.D.
3. Source might be Black and White
The colors are wrong
1. Cables from the source for proper
connections, for example, y to y
2. HUE in O.S.D.
The picture appears not to
sync up or the O.S.D.
displays “No Video
Source”
1. Cables from the source for proper
connections, for example, y to y
Component
Video YPbPr.2
Will not accept interlace-
style input.
1. This input will not accept interlace-style
input. Use YPbPr1.
Special Modes RS232C interface is not
functioning
1. Refer to Appendix C (page 30) for all
information
Service and Support
Rosen Aviation Displays, LLC
www.rosenaviation.com
PH: [phone]
Packaging and Shipping
Please repack your unit in the same fashion as it was originally packed into the shipping
container. Please include all parts of your unit so that the unit can be fully repaired, tested
and returned to you in good working order. The sender is responsible for damage to
displays that are not properly packaged for shipment. See Appendix A (page 20) for
illustration/instruction on how to package the unit for shipment in its original shipping
container. Consult your dealer or the authorized factory service center with any questions.