Rosewill Lineom User manual

User’s Manual

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
1
Contents
Disassemble Chart P.2
P.3
Accessory Box
Installation Guide
Product Overview
P.10
Information
Opening Chassis P.4
Installing Power Supply P.4
Installing Motherboard P.5
P.7~8Installing External 5.25" Device
P.7~8Installing External 3.5" Device
P.9Installing 3.5”/2.5” HDD/SSD
P.6
Installing Add On Card

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
( For reference only. Models’ option may be varied by countries. )
Disassemble Chart
Rear 120mm fan ＊
Tool-less kits for
5.25” & 3.5” device ＊
Left side panel
＊= optional
Right side panel
Front 120mm fan ＊
Front panel ＊
Space for 1x 3.5”/2.5” HDD/SSD
2
( Please refer to your motherboard’s user’s manual to connect. )
USB 3.0 CONNECTOR
USB2.0 CONNECTOR HD CONNECTOR
AC97 CONNECTOR
USB+5V
LP
LP+
GND
NC
USB+5V
LP
LP+
GND
NO PIN
AUD GND
PRESENCE#
SENSE1 RETURN
NO PIN
SENSE2 RETURN
PORT1L
PORT1R
PORT2R
SENSE SEND
PORT2L
MIC
AUD GND
RET~R
NO PIN
RET~L
MIC
MIC~BIAA
FPOUT~R
+5V
FPOUT~L
NO PIN NO PIN
NO PIN

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
Accessory Box
Cables
Motherboard
Motherboard
Stand-off
3
Motherboard
2.5” HDD
5.25” device
3.5” device
PCI card
PSU
Motherboard
3.5” HDD
PCI slot
3.5” HDD
(bottom)
5 x Cable tie
1 x PC SPEAKER
1 x Stand-off socket
6 x MB stand-off
16 x Screw B
9 x Screw C
30 x Screw A
2 x PCI cover
4 x Screw D
(Pre-installed in the case)

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
1.
2.
Unscrew to remove left and right panels.
Place the power supply from the left side into
the chassis and secure with screw-C.
NOTICE :
-If your power supply is equipped with single
fan (120mm, 135mm or 140mm), please have
the fan face to the bottom.
4

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
3.
-Install motherboard stand-offs according to your motherboard’s form factor.
-Place the motherboard onto stand-offs and secure with screw-A.
* Install/Uninstall stand-offs by stand-off socket.
12
5

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
4.
-Bend to remove the PCI slot cover.
-Install the add-on card into its position.
-Secure with screw-C.
6
A
B
C

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
5.
Confirm which bay(s) you want to install
device(s) then remove the bay cover.
Pull from the bottom to remove the front panel.
7

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
-Unlock the tool-less kit and flip it up.
-Insert external 5.25” & 3.5 “ devices into position then secure with tool-less kit(or screw-B).
UNLOCK LOCK
6.
8

© All rights reserved by Rosewill
User's ManualLINE-M
CASE
7.
A
B
2.5” HDD/SSD
3.5” HDD/SSD
Slot A - two slots for 3.5” HDD/SSD
-Insert it into its slot and secure with screw-A.
Slot B - one slot for one 3.5“/2.5” HDD/SSD
-Put it onto its slot and secure with screws from bottom.
(Screw-D for 3.5” HDD/SSD ; screw-B for 2.5” HDD/SSD)
9