Rosewill 5600 Series User manual

CASE 5600 Series
USER Manual
www.rosewill.com

CASE 5600 series User Manual
1© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Contents
Configuration
Features Descriptions
Installation
1. Opening Chassis
2. Installing Motherboard
3. Installing 3.5" HDD
4. Installing 5.25" Device
5. Installing Add on Card
6. Installing Floppy
7. Cleaning Filters-Air guide Filter
8. Cleaning Filters-Front panel Filter
9. USB port
10. IEEE1394 Port
11. Audio Port
12. System Control Connectors
Information
P. 2
P. 3
P. 5
P. 6
P. 8
P. 9
P. 1 0
P. 1 1
P. 1 3
P. 1 3
P. 1 4
P. 1 5
P. 1 8
P.16
P.17

CASE 5600 series User Manual
2© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Configuration
Dimension (W x H x D)
M/B Size
Drive Bay
Expansion Slots
Thermal Solution
Air Filter
I/O Port Bracket
Megal Material
7.9" x 17.3" x 19.4"
ATX, Micro ATX
External : 4 x 5.25" + 2 x 3.5"
Internal : 5 x 3.5"
7Slots
1 x 12 cm fan in rear and 1 x 12 cm fan holder in front
One air filter on the front panel ( only in R6A34)
Supports one I/O port bracket for standard ATX M/B
0.8 mm thickness SECC rustproof & galvanized JIS Steel

CASE 5600 series User Manual
3© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Features Descriptions
Front 120mm Fan Rear 120mm Fan Sliding Rails for 5.25"
device
Sliding Rails for 3.5" HDD
Screw-less Add-on Card
assembly
Door opening up to 270
Degree
Easy-clean filter
(in left side panel)
Easy-clean filter
(in front panel)

CASE 5600 series User Manual
4© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Screw-less and lockable
left side panel
Adjustable air inflow Front IO Ports Convenient Accessory box

CASE 5600 series User Manual
5© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Installation
1.Opening Chassis
1.1
Take off the thumb screws on the back plane
1.2
Push the Key-button
1.3
Roll the side cover anticlockwise to open
1.4
Push hooks marked in red circle to detach the
front panel from the chasis

CASE 5600 series User Manual
6© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
2.1
Due to our special design of
motherboard stand-off,copper
motherboard stand-off not needed
when you install the ATX motherboard.
2.2
Sit the motherboard on our special
motherboard stand-off and screw in all the
screws into the motherboard stand-offs.
2.Installing Motherboard
ATX Motherboard
Special motherboard stand-off
NOTE : The copper motherboard stand-off not
needed when you install the ATX motherboard.
DON'T SCREW THE COPPER MOTHERBOARD
STAND-OFF INTO THE SPECIAL MOTHERBOARD
STAND-OFF OR MOTHERBOARD INSTALLING
CAN'T BE PROCESSED SUCCESSFULLY.

CASE 5600 series User Manual
7© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
Micro ATX Motherboard
2.1
Locate and align the screw holes on the
motherboard and chasis; place the
motherboard at the correct position,
and then screw copper motherboard stand-
offs brass studs onto chassis's metal shell.
Note: Screw holes marked with "M" are
motherboard stand-off positions for micro
ATX motherboard.
2.2
Sit the motherboard on themotherboar
stand-offs and screw in all the screws
into the motherboard stand-offs.

CASE 5600 series User Manual
8© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
3.Installing 3.5" HDD
3.1
Insert the screw into the rubber pad hole on the rail
3.2
Attach rails to bothe sides of
your HDD
3.3
Insert the railed HDD into the 3.25" HDD bay and push to the buttom
NOTE : Screws for HDD have no
thread, no screwdriver needed
when you work step 3.2

CASE 5600 series User Manual
9© 2004-2006 Rosewill Inc. All rights reserved by Rosewill
4.1
Disassemble the front panel (please refer to step 1.4 )
4.2
Attach rails to both sides of your 5.25" device
PS: You can also fasten rails on your 5.25" device by screws
4.3
Insert the railed 5.25" device into the 5.25"
drive bay
4.Installing 5.25" Device