Rosewill RX355-U User manual

[RX355-U]
3.5" IDE to USB Ext. Enclosure
With Removable 80mm fan
User Manual

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
Please read this installation carefully before you use the product.
Precaution:
1. If it is a new HDD, needs to processing the disk partition
2. Win98SE and WinME do not recognize NTFS formatted drives,
so if you want to use your drive on those platforms, we
recommend you to use FAT32 instead.
3. Mac OS does not recognize NTFS formatted drives, to use your
device on both platforms, we recommend you using FAT32.
4. If you use Win2000 / WinXP/ Win Vista and FAT32, the biggest
single partition you can create will be 32GB. To create larger
partitions, you need to use the DOS command under Win98SE
or WinME or change to NTFS format.
5. Make sure the jumper settings of your hard drive is “master”.
System Requirement:
•Minimum Intel Processor II 350MHz, 64MB RAM
•Compatible with IBM PC, USB interface included，Windows
98/ME/2000/XP/Vista operate system.
•Minimum Apple G3 processor, 64MB RAM
•MAC computer system MAC OS V9.x or higher.
•Linux OS : please download kernel USB stack.
Available Interfaces
•USB 2.0 HIGH SPEED for IDE HDD
2

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
3
Protection of DC adapter:
1. Primary (Input) Protection
The input power line will be fused with a fuse 2.0A, 250 VAC.
2. Secondary (Output) protection
2.1.Over Current (OC) Protection
When an internal fault occurs, or an external fault is applied to
the power, such that an overload or short circuit is applied to
the output, the power will be shutdown. Power latch is not
allowed.
2.2 Over Voltage (OV) Protection
If an over-voltage fault occurs on the adapter output, the power
will shutdown.
2.3 Short Circuit Protection
The power will protect itself, and shut down, if a short circuit is
placed between DC return and the output. This condition will
cause no damage to the power. Power latch is not allowed.

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
4
Package Contents
USB 2.0 interface
Item Quantity
3.5” External Enclosure 1 pcs
Driver Disk 1 pcs
Installation Guide 1 pcs
AC adapter 1 pcs
USB cable 1 pcs
Foot stand 1 pcs
Screw Kit 1 set
Fan kit 1 set

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
5
FEATURE
1. Standard USB 2.0 high speed transfer rate.
2. Aluminum HDD framer for easy installation.
3. Removable 80 mm fan kit.
4. Suitable for all 3.5" IDE HDD.
5. All aluminum and super slim design, to enhance heat dissipation.
6. Foot-stand for vertical style.
7. Plug and play & Hot Swappable
8. Built-in with integrated 80 mm ultra silent cooling fan provides
excellent heat dissipation.
9. Fan control for the 80mm cooling fan
10. LED indicator
11. Support up to 750 GB HDD

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
6
Technical Specifications
External Interface USB 2.0 ( Speed up to 480 Mbps)
Internal Interface 3.5” IDE HDD
Connectors USB B receptacle
Operating
System
Win 98SE/ME/2000/XP/Vista
Mac OS 9.x and above.
IDE Standard Compliant with ATA-6 UDMA 66/100/133
HDD Space Up to 750GB
LED Power On / Access
Power Supply AC Adapter 12V / 2A
AC Input 100V ~240V full range
Dimensions 220(L) x 130(W) x 65(H) mm
Weight 2.43 lbs.
Certification CE

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
7
Installation Guide:
1. Release the screws to pull out the HDD frame.
2. Fix the HDD by screws (after HDD located with the connecter).
3. Pull in the frame into external box.
4. Fix the rear panel by screws.

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
8
5. After connect transfer cable and Power cord, the external HDD will
appear the relativity
6.Cooling fan cable installation:
Plug to DC fan cable into rear panel & cooling fan’s DC jack, and the
fan will be operating after the power on. (Please view image below)
Attention:
1. Only one interface at one time can be used
2. If this HDD is new one, please partition & format disk,
otherwise the system cannot detect HDD.
3. The HDD jumper should be set to “master”.
4. Make sure your PCI Host Card is installed correctly
5. If required, update your OS (win 2000 to SP4, Win XP to
SP1a)
6. Only one computer at one time can access the drive.

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
9
Driver Installation:
Windows 98SE
1. After plug the external box into, the system will remind you
there is a new hardware of USB Storage Adapter adds into.
2. Design the driver of the safe path (in the driver), the system
will active the installation automatically.
3. After for a while, click "My Computer", USB HDD will appear
the relativity on the PC.
Windows ME/2000/XP/Vista
The system already provided support for the software.
MAC OS 9.x or above
OS 9.X edition:
The system already provides support for the software.
The divided partition of the external HDD
Win 98SE/ME SYSTEM
FDISK is command that doing the divided partition to HDD, The step
of how to divided partition from the HDD by using FDISK as follows:
1. Plug the cable of USB into PC, and be sure that the PC has
identified HDD.
2. Execute "FDISK" under the model of COMMAND.
3. After enter the FDISK program [If the FDISK program does not work,
please restart your PC again (don't plug out the USB HDD) then it will
be work]. Firstly select "The fifth item" --select the USB HDD you
want to divided partition for and then just see the illustration as
follows: Then just follow the instruction to divided partition for the
HDD of USB.

3.5" IDE to USB Ext. Enclosure With Removable 80mm fan UserManual
10
Windows 2000/XP/Vista
Plug the HDD into your system it will appear the hot plug a play. Just
click “Control Panel”/ “manage tool” / “computer management” /
“Disk management”. All the disk connects to the PC will appear on
the chart, as well as the state of the HDD. Find out the HDD and click
the right bottom of the mouse under the state of chart, just follow the
step. Take a look of the icon on the bottom.
Mac OS
Mac OS9.x and earlier version does not support creating partition on
an external HDD. For your new HDD, you need to purchase additional
3rd party software to creating your HDD partition.
For Mac OS X, use the Disk Utility to format and divided partitions on
your external disk.
• Select “Disk Utilities” in the utilities folder.
• Choose your external drive and format it.
Notice: If you want your ENCLOSURE on a Windows as well as on
your Mac OS, we recommend you to use a PC to format the drive.
Choose FAT32 format and do not change anything on the partition or
format on your Mac, otherwise the Windows OS can not be able to
recognize the ENCLOSURE.