Rosslare DR-U955BT User manual

DR-U955BT
Multi-format Desktop Reader
User Manual
1
1. Introduction
The DR-U955BT is an advanced desktop reader for MIFARE Classic®
EV1, MIFARE®DESFire®EV1, UHF, and BLE. It reads the ID data of the
credential and transmits the relevant ID data to any connected access
control software, such as Rosslare’s AxTraxNG™.
It has a slim and attractive design and is built for convenience and
portability. With its USB computer interface, it is quick and easy to install
and runs without any additional power source.
Using the BLE-Admin™or My BLE-ID™apps, the reader can function
like other Rosslare BLE readers and can transmit the BLE ID to the reader.
The Hardware Configuration Tool (HCT) can be used to configure the
reader’s specifications, such as the Wiegand format used.
The reader reads the CSN ID of each credential (MIFARE, UHF, BLE) and
transmits it to the software with the bit length pre-configured by the user.
Figure 1: DR-U955BT
2. Technical Specifications
2.1 Electrical Characteristics
Operating Voltage Range
5 VDC (USB powered)
Standby Current
250 mA
Max. Operation Current
300 mA
Supported Transponders
MIFARE, UHF, BLE
Read Card Distance
UHF and MIFARE: Up to 5 cm (2 in.)
BLE: Up to 6 m (19.7 ft)
Operation Frequency
•RFID: 13.56 MHz
•DR-U955BT US: 902–928 MHz
(America) RFID
•DR-U955BT EU: 865–868 MHz
(Europe) RFID
•Bluetooth: 2.402-2.480 GHz
Output Formats
Supports Wiegand 26-Bit to 64-Bit
2.2 Environmental Characteristics
Operating Environment
Indoor use
Operating Temperature Range
0°C to 63°C (32°F to 145°F)
Storage Temperature Range
-20°C to 63°C (-4°F to 145°F)
Relative Humidity Range
0 to 95% (non-condensing)
2.3 Physical Characteristics
Weight
130 g (4.6 oz)
Dimensions (L x W x H)
123 x 70 x 16.2 mm (4.9 x 2.8 x 0.6 in.)
3. Operation
The DR-U955BT appears as a COM port device when plugged in to a PC and can be used for any application. When a card is presented to the reader, the reader
outputs the Wiegand ID data on the COM port only once until a new card is presented.
You must use the AxTraxNG software to enroll cards. Please refer to the relevant appendix in the AxTraxNG™ Software Installation and User Manual.
For the enrollment reader to function in AxTraxNG, you must know the COM port being used. The COM port can be found in Microsoft Device Management’s
driver details under ‘Ports (COM & LPT)’. The port being used appears as “USB serial Port (COMx)”, where x is the number of the port used.
4. Configuration with the BLE-Admin App
1. Download the BLE-Admin application from Google Play or App Store
using the following QR code.
2. Open the application, select the required reader from the list displayed.
3. Enter the password.
NOTES:
•Use the default password (12345678) when you log in to the
BLE-Admin application for the first time.
•It is highly recommended that you change the password (see step 4).
4. On the main screen, configure the following:
Options
Remarks
Desktop Reader Name
Assign name to select the Desktop Reader Name
Password
Change password
5. Tap Set Configuration and configure the following
Parameters
Options
Remarks
Power
Power = 1 –10
Default = 10
Slide to select the signal power effect
of UHF reading range credentials.
Transmission Protocol
Wiegand
This is a proprietary protocol that the
reader uses to send the tag information
to the AxTraxNG software.
Transmission Protocol
Type
26, 32, 32R, 34,
40, 56, 64 bits
Default = 26 bits
Select number of bits.
NOTE: The My BLE-ID application allows a mobile device to be used as a
credential. Download the application from Google Play or App Store using
the following QR code.
S M A R T

2
0706-0960664+01
Declaration of Conformity
▪This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
▪This device may not cause harmful interference.
▪This device must accept any interference received, including
interference that may cause undesired operation.
▪Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
▪Reorient or relocate the receiving antenna.
▪Increase the separation between the equipment and receiver.
▪Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
▪Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the Quick
Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the Warranty
Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
22 Ha'Melacha St., P.O.B. 11407
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
CERT
ISO 9001
ISO 14001