Rosslare DR-12C User manual

DR-12C
EM Card Desktop Reader
User Manual
1
1. Introduction
The DR-12C is an advanced EM Card Desktop Reader. It reads the EM
card identification number and transmits it to connected access control
software, such as Rosslare’s AxTraxNG™.
It has a slim and attractive design and is built for convenience and
portability. With its USB computer interface, it is quick and easy to
install and runs without any additional power source. Designed to sit
safely on any desktop, the DR-12C is sturdily built, with surface-
gripping rubber feet.
Figure 1: DR-12C
2. Technical Specifications
2.1 Electrical Characteristics
Operating Voltage Range 5 VDC (USB powered)
Standby Current 70 mA
Max. Operation Current 90 mA
Supported Transponders EM Cards
Read Card Distance Up to 5 cm (2 in.)
RF Modulation ASK
Operation Frequency 125 kHz
Output Format Wiegand 26-Bit
2.2 Environmental Characteristics
Operating Environment Indoor use
Operating Temperature Range 0°C to 63°C (32°F to 145°F)
Storage Temperature Range -20°C to 63°C (-4°F to 145°F)
Relative Humidity Range 0 to 95% (non-condensing)
2.3 Physical Characteristics
Weight 130 g (4.6 oz)
Dimensions (L x W x H) 123 x 70 x 16.2 mm (4.9 x 2.8 x 0.6 in.)
3. Installing the USB Driver
Before you can use the reader, you must download the proper driver.
The driver supports the following operating systems:
Windows 7 32- and 64-Bit
Windows Vista and Vista 64-Bit
Windows XP and XP 64-Bit
Server 2003, XP, and Server 2008
Windows 10 (32-Bit and 64-Bit)
To install the USB driver:
1. Go to http://www.rosslaresecurity.com.
2. Click Download Center in the Quick Links section.
3. In
Document Types , select Driver and click Search.
The driver for the reader appears.
4. Click the Download icon on the right.
The file is downloaded to your computer.
5. Go to the downloaded file (CDM20824_Setup) and double-click it.
After a few moments, a completion message appears and the
window closes.
4. Operation
When the computer has successfully installed the driver, the DR-12C
appears as a COM port device when plugged in to a PC and can be
used for any application. When a card is presented to the reader, the
reader outputs the Wiegand ID data on the COM port only once until a
new card is presented.
You must use the AxTraxNG software to enroll cards. Please refer to
Appendix J in the
AxTraxNG™ Software Installation and User Manual .
For the enrollment reader to function in AxTraxNG, you must know the
COM port being used. The COM port can be found in Microsoft Device
Management’s driver details under ‘Ports (COM & LPT)’. The port being
used appears as “USB serial Port (COMx)”, where x is the number of
the port used.

2
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to
operate the equipment.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Limited Warranty
The full ROSSLARE Limited Warranty Statement is available in the Quick
Links section on the ROSSLARE website at www.rosslaresecurity.com.
Rosslare considers any use of this product as agreement to the
Warranty Terms even if you do not review them.
Contact Information
United States and Canada
Rosslare Security Products, Inc.
Southlake, TX, USA
Toll Free: [phone]
Local: [phone]
Fax: [phone]
[e-mail]
Europe
Rosslare Israel Ltd.
Rosh HaAyin, Israel
Tel: [phone]
Fax: [phone]
[e-mail]
Latin America
Rosslare Latin America
Buenos Aires, Argentina
Tel: [phone]
[e-mail]
China
Rosslare Electronics (Shenzhen) Ltd.
Shenzhen, China
Tel: [phone]
Fax: [phone]
[e-mail]
Asia Pacific, Middle East, Africa
Rosslare Enterprises Ltd.
Kowloon Bay, Hong Kong
Tel: [phone]
Fax: [phone]
[e-mail]
India
Rosslare Electronics India Pvt Ltd.
Tel/Fax: [phone]
Mobile: [phone]
[e-mail]
www.rosslaresecurity.com
0706-0960609+01