Royalcraft SORRENTO User manual

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 2 / 5
www.ro
y
alcraft.co.uk
Before you start
Warnings
Dos
Don’ts
Two people
Time to assemble
30 minutes
Tools required
Tips:
It is best not to fully tighten the nuts and
bolts until they are all correctly located.
Only carefully tighten them when you are
satisfied with the alignment of all
components.
Be careful not to overtighten.
SORRENTO 90CM BLACK GLASS TABLE
WITH PARASOL HOLE
Assembly Instructions
IMPORTANT, RETAIN FOR FUTURE REFERENCE
READ CAREFULLY
See enclosed instructions for assembly, safety and care
information.
Failure to follow the warnings could result in serious injury.
Handle heavy parts with care.
Ensure that this product is fully assembled as illustrated before use.
This product should only be used on firm, level ground.
Keep small parts out of reach of children.
This product is intended for domestic use only.
Ensure the product is always placed on level ground.
Furniture can be dangerous if incorrectly used. No liability will be
accepted for damage or injury caused by incorrect use of this
product.
Do not use scourers, abrasives, washing powders, chemical
cleaners or any other substances containing abrasives since
these substances can damage the product, including the glass
panel.
To preserve the table top design do not place greasy / oily items
directly onto the surface. Use place-mats to prevent spillages
of food or drink.
Do not place very hot or very cold items on the glass surface
unless adequately thick table-mats are used to prevent such
items from coming into contact with the glass.
Do not use the table as a chopping surface.
Do not strike the table with hard or pointed items.
Do not sit or lean on the table.
Do not use power tools to construct this product.
Do not use this product if parts are missing, damaged or worn.
Do not stand or climb onto the product and do not use it as a
ladder, as this could lead to it unbalancing and overturning.
Never drag furniture when moving it, always lift it.
Number of people required for assembly
When you are ready to start, make sure that you have the right
tools, plenty of space and a clean, dry area for assembly.
Unwrap all packaging materials and place the components on a
suitable surface to prevent scratching your product.
Check all contents are present prior to assembly as per the parts
list provided. In the event of problems or missing parts, please
contact the seller.
Check all screws and bolts are tightened and inspect regularly.
Cover furniture when not in use to add additional protection to your
product.
Frames are manufactured using powder coated aluminum tubing.
Any scratches on the paintwork should be touched up immediately
with metal paint to prevent corrosion.
During severe weather conditions, including high winds, rain, hail,
thunderstorms, extreme heat and cold temperatures, the product
should be stored inside in a cool, dry place.
To best preserve this product, please use a protective cover when
your furniture is not in use. We would also recommend using a
gazebo or parasol over your furniture during the summer period and
prolonged sunny spells. This will help prevent harmful UV rays from
damaging and discolouring the material.
Ensure that the product is clean and dry before storage.
Clean your product with a sponge and warm soapy water then wipe
with a clean, dry cloth.
Where instructions as to the; storage, commissioning, installation,
use and maintenance of the goods or (if there is none) good
trade practice are not followed and a defect arises this will void
the 12 month manufacturer's guarantee on the product.

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 3 / 5
www.ro
y
alcraft.co.uk
Components, fixtures & fittings (not actual size)
Parts List
Part
No. Diagram Qty. Part No. Diagram Qty.
A
Table Top Frame
1 PC B
Table Leg
4 PCS
C
Glass Top
1 PC D
Bolt
8 PCS
E
Spring Washer
8 PCS F
Washer
8 PCS
G
Bolt Head Cap
8 PCS H
Allen Key
1 PC
SORRENTO 90CM BLACK GLASS TABLE
WITH PARASOL HOLE
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 4 / 5
www.ro
y
alcraft.co.uk
Step by step assembly instructions
Step One
Place the Glass Top (C) at a safe, flat surface, don’t let it hinder the assembly of other
components.
With the help of another person, place Table Top Frame (A) upside down on a flat, non-
abrasive surface to avoid scratching the table surface or rim.
Step Two
Attach the Table Legs (B) onto the Table Top Frame (A) using Washers (F), Spring
Washers (E) and Bolts (D).
Only tighten the bolts when all bolts and washers are in place and turn freely. Once you
are satisfied with the alignment of the components, carefully tighten all bolts using Allen
Key (H). Do not over-tighten.
Cover each bolt with Bolt Head Caps (G).
G
D
E
FA
B
A
B
SORRENTO 90CM BLACK GLASS TABLE
WITH PARASOL HOLE
Assembly Instructions

Produced in China for A. Mir & Co., Ltd.
© A. Mir & Co., Ltd. 5 / 5
www.ro
y
alcraft.co.uk
Step Three
With the help of another person, carefully turn over the table frame and place it in the upright
position.
Carefully place the Glass Top (C) onto the Table Top Frame (A), make sure they match each
other.
Step Four
There are adjustable feet screws at the bottom of the legs.
Make sure there is no wobbling by adjusting the feet screws when the table is placed on the
flat ground.
Your table is now ready for use.
Note: This table is not designed to hold the parasol separately.
Parasol base with suitable weight should always be used.
PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE
C
A
SORRENTO 90CM BLACK GLASS TABLE
WITH PARASOL HOLE
Assembly Instructions