Rugged Ridge 11703.04 User manual

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 1/4
Part #11703.04
OMIX-ADA®TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649
FOR WARRANTY OR TECH CONCERNS EMAIL: [email protected]
Components
1. Side Rail, Driver Side ................................................................. 1
2. Side Rail, Passenger Side ......................................................... 1
3. Rear Panel................................................................................. 1
4. Front Panel ................................................................................ 1
5. Center Brace ............................................................................ 5
6. Roof Bracket ............................................................................. 6
7. Clamp for Roof Bracket........................................................... 6
8. M8 X 25mm Button Head Allen Bolt ..................................... 18
9. M8 X 16mm Button Head Allen Bolt ..................................... 18
10. Flat Washer.............................................................................. 36
11. Serrated Flange Nut............................................................... 30
12. Allen Key.................................................................................... 1

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 2/4
Part #11703.04
2. Now move to the front of the rack. Slide the center
braces through the rack. There is a total of ve
pieces to install.
1. Start by attaching the rear section of the rack
to the side rails. Use the smaller button head with
washer and serrated ange nut. Snug but don’t fully
tighten at this time.
3. Slide the 5 center braces into place now attach
with hardware. The rst, middle and last center brace
requires the longer button head bolt to pass through
the center brace, rack and roof bracket. The second
and forth center brace will use the shorter button
head bolt to attach. Snug all the hardware but not
fully tighten at this time. With it only snug it allows you
to adjust the roof bracket when placing it on the
Jeep later.

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 3/4
Part #11703.04
5. Now t the front panel to the rack. It attaches
with the short button head with washer and serrated
ange nut. Now the rack is assembled fully tighten all
the hardware except the hardware holding the roof
brackets. These feet need to stay exible to adjust to
t to the roof.
NOTE: At this time attach LED cubes to the front
panel if you choose.
4. Here’s a look at the roof rack assembled at this
point. All hardware is snug but not tighten at this
time.
6. Now place rack on the Jeep roof. This must be
done with two or more people. The rack weighs
more than 100lbs so please use precaution before
lifting. We also suggest place a blanket on the roof
to avoid scratching the roof while placing the rack.

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 4/4
Part #11703.04
8. Now place the roof bracket outer clamp to the
roof bracket. Attach with button head bolt and
washer.
7. With the rack placed on the roof slide the roof
brackets to t in the roof channel. Adjust as needed
and measure to assure the rack is centered and
square to the Jeep.
9. To complete the install fully tighten the roof
bracket hardware.
We strongly encourage you to keep the provided
Allen key in the glove compartment. That way the
roof bracket can be checked to assure them tight to
the roof from time to time.