Rugged Ridge 13711.15 User manual

Page 1 of 6
Front Door Content: 13711.15 (2dr/4dr)
1. Soft Upper Door frame with Cover
2. Adjustment Collar
3. Allen Wrench
4. Velcro Strip (38”)
Rear Door Content: 13712.15 (4dr)
1. Soft Upper Door Frame with Cover
2. Adjustment Collar
3. Allen Wrench
4. Velcro Strip (30”)
JK Upper 1/2 Door Installation Instructions
Quantity:
2
4
1
2
This product is intended to provide added “o-road” convenience and utility to your vehicle.
This product is not intended to provide occupant containment or protection in the event of an accident or roll-
over. Further,“on road” use may involve increased risk of serious injury in the event of side-impact accidents. To
reduce risk from these types of injuries: Always wear seat belt and shoulder harness for all vehicle occupants.
Keep arms and body inside vehicle. Drive safely, read and understand all manufacturers warnings and product
instructions before installation.
NOTICE: The Rugged Ridge soft upper doors when used in conjunction with the Rugged Ridge Half Doors are
designed to provide the best possible protection from the elements; however, due to the nature and intended
use of this product, extreme conditions such as driving rains, high wind gusts, automated car washes, etc. may
cause leaking to occur.
1. Lower 1/2 doors will need to be cleaned using isoproply (rubbing) alcohol. Clean the 2”along the top edge
where Velcro is to be installed. Installation should be performed between (65F-110F).
Upper Soft Door Kit (Front) 2dr - 4dr JK : 13711.15
Upper Soft Door Kit (Rear) 4dr JK: 13712.15
Quantity:
2
4
1
2
Pic. 1 Pic. 2 Pic. 3
2. Apply Velcro to outer edge of front lower 1/2 door. With 2” of backing tape removed position Velcro 1/8”
below top edge of door (Pic. 2). Working forward from rear of door slowly apply Velcro to door maintaining
1/8” spacing from top edge. For front doors cut a “V” shaped notch 3/4 through Velcro at each bend. This will
allow the Velcro to follow the door line without bunching (Pic. 3). Press Velcro rmly in place to ensure good
adhesion.
Front 1/2 Door Installation

Page 2 of 6
3. For front doors drape Velcro over the top of the mirror mounting base (Pic. 4). Make a small cut where the
mirror base begins and where it ends. Pull the Velcro back and cut out the shape of the mirror mounting
base (Pic. 5). With Velcro mounted to doors trim edges and press rmly into place (Pic. 6).
4. Slide (1) of the supplied adjustment collars onto each of the support legs (Pic. 7). No collar is required on the
middle support leg of front upper doors. Tighten set screw just enough to keep in place but also allow up
and down movement.
Pic. 4 Pic. 5 Pic. 6
Pic. 7 Pic. 8 Pic. 9
Please Note: Each upper door frame will need adjustments to achieve the best possible t. Upper door tment
is directly related to the alignment of the lower 1/2 doors. Several attempts may be needed to
achieve proper tment for each door. Read instructions completely prior to installing.
Installation of upper door frames to lower 1/2 door.
5. Place upper doors into lower 1/2 doors (Pic. 8). NOTE: Upper doors frames will have a tight t and is
considered normal. The tight t reduces upper door bueting at highway speeds. Powder coating thickness
can vary and may aect the t. If this occurs it will be necessary to remove some powder coating on leg
supports. Using sandpaper remove only what is needed to allow upper frame to t.
6. With upper door installed allow door to rest into lower 1/2 door and secure Velcro (Pic. 9).

Page 3 of 6
7. With door closed a 1/8”gap should be visible at top corners (Pic. 10). If there is more or less than a 1/8” gap
at top corners further adjustment will be needed.
8. To adjust corners up place palm of hand on top corner of upper door. Push up slightly to raise frame
(Pic. 11).
9. To adjust down place palm on top corner of upper door. Tap down to lower frame (Pic. 12)
Pic. 10 Pic. 11 Pic. 12
10. With upper door centered and a 1/8”gap at top corners tighten collar set screws with supplied allen
wrench (Pic. 13). Do not over tighten.
11. Pull and reposition Velcro to lower door (Pic. 14). Inspect side corners, and top of upper door for tight seal to
door frame (Pic. 15). From inside vehicle look at upper door and inspect for visible light. If light is visible then
further adjustment will be needed.
Pic. 13 Pic. 14 Pic. 15
12. Pictures 16, 17, and 18 show how upper door frames should look installed. If light can be seen from inside
vehicle follow instructions on page 4 explaining how to obtain a proper seal to vehicle door frame.
Pic. 16 Pic. 17 Pic. 18

P
age 4 of 6
Door Seal Adjustment Procedures (Front Doors)
13. From inside of vehicle inspect upper door frames for visible light entering around the door seal. If light is
visible frames will need to be bent slightly inward (towards vehicle) to eliminate gaps.
14. Before proceeding make sure steps (4 - 12) have been followed correctly. Upper door frames must be
centered within door frame and a 1/8” gap visible at top corners (Pic. 19). Failure to align upper doors
correctly may result in leaks around seals.
Pic. 19
15. Upper door frame corners will need to be adjusted independently. Start with upper corner that appears to
have the largest visible gap (Pic. 20). Open door and grab the base of frame and top corner. Pull frame back
from the top (Pic. 21). Small adjustments should be made (DO NOT OVER BEND). Close door and inspect for
visible light. Continue to make small adjustments to achieve best t.
Pic. 20 Pic. 21
16. Inspect opposite corner for gap. Some adjustment is suggested even if no light is visible. This will ensure a
tight seal. Open door and grab the base of frame and top corner. Pull frame back from the top (Pic. 22).
Small adjustments should be made (DO NOT OVER BEND). Close door and inspect for visible light. Continue
to make small adjustments until a tight seal is made around door opening.
17. Open and close front door several times. Upper door front corner should just make contact with windshield
frame as the door is closed. If upper door is bent too far inward the door will not close correctly and the
upper door will need to be bent back out. To bend outward grab the base of frame and top corner. Hold
base and push outward on frame. Small adjustments should be made (DO NOT OVER BEND). Open and
close door between each bend until slight contact is made as door is closed (Pic. 23).
18. For nal inspection close door and check door alignment one more time. If upper door is not centered and
or has more than a 1/8”gap at top corners the frame will need to be readjusted using adjustment collars.
Adjust lowest corner rst. Loosen set screw in adjustment collar (Pic. 24). Repeat steps (6-18) as needed.
When door is positioned correctly tighten collar set screws.
Pic. 22 Pic. 23 Pic. 24

P
age 5 of 6
Door Seal Adjustment Procedures (Rear Doors)
Pic. 28 Pic. 29 Pic. 30
Pic. 25 Pic. 26 Pic. 27
19. Open half door and grab the excess weather-stripping closest to the Windshield frame. Place the weather
stripping behind the post of the soft upper frame (Pic. 25). Adjust as needed to ll gap between windshield
frame and upper door .
20. Trim rear weather-stripping so that it slightly overlaps the weather-stripping of the half door (Pic. 26 -27).
21. Rear upper door frames are installed using the same procedures and techniques discribed in steps (2-19).
22. Apply Velcro to lower doors as described in step (2). Velcro should be positioned 1/8” from the top of lower
1/2 door. Press Velcro rmly into place to ensure good adhesion (Pic. 28).
23. Position rear upper frames onto lower doors. Top corners should have a 1/8” gap between the top of
upper door and soft top (Pic. 29). Adjustment of rear upper doors will be the same as fronts. See steps (4-12)
for proper alignment procedures.
24. After upper doors have been positioned correctly with 1/8” gaps check for visible light from inside vehicle.
If light is visible rear upper doors should be adjusted in the same manner as the fronts (Pic.30).
See steps (14-19) for proper alignment procedures.
25. When bending frames small adjustment should be made. (DO NOT OVER BEND) Continue to make small
adjustments until a tight seal has been made around door opening.

P
age 6 of 6
28. With door closed inspect outside alignment. If upper door is not centered and/or has more than a 1/8”gap at
the top corners the frame will need to be readjusted using adjustment collars starting with lowest corner rst.
29. With door centered tighten set screws and readjust Velcro to door. Check for visible light from inside vehicle.
If light is present repeat steps (22-29).
Pic. 31
Features and Functions of Soft Upper Doors
For assistance, please contact Omix-ADA Technical Support department
[phone]
[email protected]
© Copyright 2011, Omix-Ada
26. With rear doors aligned open and close doors several times. As the rear door closes the upper door front corner
should rest on door frame and slide into place (Pic. 31). This contact with rear door frame insures a weather
tight seal and is considered normal.
Pic. 32 Pic. 33
Rugged Ridge upper door windows can be set in 3 new distinct positions. By unzipping the window and sliding
plastic dowels through the elastic straps the door can be congured as shown.
Half Fold Rear Fold Front Fold
This feature will allow air ow to be tailored as needed and will prolong the life of the upper door fabric,
zipper and plastic window.
27. If upper door falls below plastic surround or binds as door closes (Pic. 32) the upper door will need to be bent
back away from vehicle ( Pic. 33). (DO NOT OVER BEND) Small adjustments should be made until proper contact
with door frame is achieved.
30. Trim weather stip as discribed in step (21).