Rugged Ridge JL User manual

Copyright © 2020 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 1/4
Part #11703.05
OMIX-ADA®TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649
FOR WARRANTY OR TECH CONCERNS EMAIL: [email protected]
Components
1. Side Rail, Driver Side ................................................................. 1
2. Side Rail, Passenger Side ......................................................... 1
3. Rear Panel................................................................................. 1
4. Front Panel ................................................................................ 1
5. Center Brace ............................................................................ 3
6. Roof Bracket ............................................................................. 4
9.M8 X 20mm Button Head Allen Bolt (Shorter Bolt)............... 16
10.Flat Washer .............................................................................. 60
11.Nyloc Nut ................................................................................. 18
12.Allen Key..................................................................................... 1
13.Front Corner Braces....................................................................2
14.Rear Corner Braces.................................................................... 2
4
12
3
5
5
5
6
66
6
77
7
7
8910 11
7.Clamp for Roof Bracket .......................................................... 4
8. M8 X 25mm Button Head Allen Bolt (Longer Bolt) .............. 16
13 14
13 14

Copyright © 2020 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 2/4
Part #11703.05
1. Start by attaching the rear section of the rack to
the side rails using the Corner Braces. The Corner
Braces will install from the inside. Use the smaller
button head with 2 washers and Nyloc nut. Snug
but don’t fully tighten at this time.
2.Slide the 3 center braces into place and attach
with hardware. Use the longer button head bolts with
2 washers and Nyloc nut. Snug all the hardware but
don't fully tighten at this time. With it only snug, it
allows you to adjust the roof bracket when placing it
on the Jeep later.
3.Attach the front panel to the rack using the
Corner Braces. The Corner Braces will install from
the inside. Use the short button head with 2
washers and Nyloc nut. With the rack
assembled, fully tighten all the hardware except
the hardware holding the roof brackets. These
feet need to stay flexible to adjust to fit to the
roof. NOTE: At this time attach LED cubes to the
front panel if you choose.

Copyright © 2020 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 3/4
Part #11703.05
4.Place the rack on the Jeep roof. This
must be done with two or more people.
The rack weighs more than 100lbs so
please use caution before lifting. We also
suggest placing a blanket on the roof to
avoid any scratching.
5.With the rack placed on the roof, slide
the brackets to fit in the channel. Adjust
as needed and measure to assure the
rack is centered and square to the Jeep.
6.Install outer clamp to the roof
bracket. Attach with 4 longer button
head bolt and washer.

Copyright © 2020 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Roof Rack Basket, JL & JT
Page 4/4
Part #11703.05
7.To complete the install, fully tighten the roof
bracket hardware.
We recommend checking the bolts periodically for
tightness. Please keep provided Allen Key.