Rugged Ridge 13551.33 User manual

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Dash Multi Mount System with Charger, JK 2007-2010
Page 1/3
Part #13551.33
OMIX-ADA®TECHNICAL SUPPORT
PHONE: M-F 8am - 5pm EST 1-800-449-6649
FOR WARRANTY OR TECH CONCERNS EMAIL: [email protected]
Components
1. Mult-Mount Tray........................................................................ 1
2. Wireless Charging Phone Mount ............................................ 1
3. USB Charging Cord .................................................................. 1
4. Dual USB Charging Port ........................................................... 1
FCC Part 18 Compliance Statement for Wireless Charger.
This equipment has been tested and found to comply with the limits
for a WPC device, pursuant to Part 18 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
in a residential installation.
This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
1-Increase the separation between the equipment and the receiver.
2-Reorient or relocate the receiving antenna.
3-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4-Consult the dealer or an experienced radio/TV technician for help.
Information to the user:
1. Do not disassemble or throw into re or water, to avoid damage.
2. Do not use wireless charger in severely hot, humid or corrosive
environments, to avoid circuit damage and occurs
leakage phenomenon.
3. Do not place too close with magnetic stripe or chip card (ID card,
credit cards, etc.) to avoid magnetic failure.
4. Please keep the distance of at least 30cm between implantable
medical devices (pacemakers, implantable cochlear, etc.)
and the wireless charger, to avoid potential interference with the
medical device.
5. Take care of children, to ensure that they won’t play the wireless
charger as a toy.
6. Some phone case may affect the charging performance. Ensure
there is no any metal object between your phone
cases or try to take it off before charging.
7. Device should not be installed near maritime safety communications
equipment or other critical navigation or communication equipment.
Specication:
Input : DC 5V-2A, DC9V-1.67A
Output : 10W Max
Frequency range: 0.15 MHz - 30MHz
Color : Black

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Dash Multi Mount System with Charger, JK 2007-2010
Page 2/3
Part #13551.33
Step 2
Install Multi-Mount Dash Storage by snapping front lip
into dash, then pressing back tabs into place.
Step 1
Remove factory dash cover above center console.
Unscrew remote compass module from factory dash.
Use screws to reattach remote compass module to
Multi-Mount Dash Storage.
Step 3
The Ball mount should be attached to your
accessory mount base. If it isn’t then attached with
provided hardware as shown.

Copyright © 2019 Omix-Ada®, Inc.
460 HORIZON DR. | SUWANEE, GA 30024 | PHONE: [phone] | FAX: [phone] | www.Omix-ADA.com
Rugged Ridge Dash Multi Mount System with Charger, JK 2007-2010
Page 3/3
Part #13551.33
Step 4
Place outer ring over end of ball mount.
Step 5
Press phone mount into ball mount.
Note: Image shown here is the non-charging base,
the charging base mounts in the same manner.
Step 6
Pull outer ring over phone mount adapter and
thread tightly to secure.
Step 7
Route power cord from charging base to a USB
power port. If you choose to use the powered duel
USB port provided then install in a precut switch pod
or cut a provision to install. When wiring power to the
USB port make sure to include in-line fuse.