Rutland county garden furniture Morcott triple bin User manual

Assembly Instructions

The Morcott Triple Bin Store

Before you commence the assembly process we recommend that you read these instructions thoroughly beforehand to

familiarise yourself with the assembly process and to also check that you have the correct components. If for any reason you

need assistance, you can find our contact details on the final page of these instructions.

We highly recommend that any assembly is carried out on an open flat, level surface if possible with sufficient space.

Tools required:

10mm spanner/socket, No2 Pozidriv screwdriver (or electric driver)

Components

38 x 65mm,

4 x75mm screws

3 x Latch keep &

48 black screws

3 x Prop fixing

2 x Spacer blocks

3 x Metal bar

3 x Chain

1 x Left panel

1 x Right panel

3 x Back panel

2 x Outer lid

assembly

1 x Centre lid

assembly

3 x Door

2 x Dividing frame

3 x Prop

1 x Hinge strip

1 x Finishing strip

The Morcott Triple Bin Store

Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,

Aslackby, Sleaford, Lincs, NG34 0HZ.

Company No: 11025348 VAT No: 282569762

Step 1

Step 2

Begin by arranging the left panel (the one with the small

wood block attached to the front post) and the back

panel at 90° to each other, with the back panel raised up

on the spacer blocks by approximately 25mm. Use 3 x

65mm screws to secure as shown.

Now add the Dividing frame, fixing in the same way with 3

x 65mm screws.

Step 3

Step 4

Continue by adding the remaining back panel and final

side panel in the same manner as before.

Carefully lay the assembly on its back and attach the metal

bars, the centre bar being the shorter one, to the front

bottom edge of the 3 front posts as shown, securing in

place with 2 x 65mm screws per post.

The Morcott Triple Bin Store

Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,

Aslackby, Sleaford, Lincs, NG34 0HZ.

Company No: 11025348 VAT No: 282569762

Step 5

Step 6

Stand the assembly back up and position the Hinge strip

at the top of the rear posts...

…set the hinge bar so that the top edge sits approx. 15mm

above the top of the rear post and secure in place with a

75mm screw into each of the 3 posts.

Step 7

Step 8

Lower the lid assemblies into place, the centre lid being

the narrower one, and position them so that the hinge

knuckles sit against the hinge strip...

..and there is a 15mm gap between the lid panels before

fixing the hinges into place with 3 x black screws per hinge

into the hinge strip.

The Morcott Triple Bin Store

Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,

Aslackby, Sleaford, Lincs, NG34 0HZ.

Company No: 11025348 VAT No: 282569762

Step 9

Step 10

Returning to the front of the store, place the finishing strip

against the 3 front posts as shown with the screw holes

configured to create a triangle and slide it upwards until it

is just touching the underside of the lid. Now fix in place

with 3 x 65mm screws per post.

Align the door (hinge side on the left) so that the top edge

clears the underside of the finishing strip by approx

10mm and each hinge leaf sits flat against the post with

the knuckles resting against the front edge of the post.

Secure the hinges in place using 8 x black screws.

Step 11

Step 12

Attach the second and third door in the same manner.

Position the cabin latch keep on the post and aligned

horizontally with each latch as shown. Secure in place

with 2 x black screws then repeat for the second and third

door.

The Morcott Triple Bin Store

Rutland County Garden Furniture Ltd, Ashbourne House, 2 Dovecote Meadows,

Aslackby, Sleaford, Lincs, NG34 0HZ.

Company No: 11025348 VAT No: 282569762

Step 13

Step 14

Take the coach bolt from the prop fixing and push it

through the hole in the prop, add a washer and then push

through the hole in the lid batten as shown.

Place another washer over the coach bolt and finally the

securing nut. Tighten with a spanner or socket until fully

tight and then back off until the prop is able to swing

freely. Attach the second and third prop in the same

manner.

Step 15

Step 16

If your bin lid has a suitable handle you may use the chain

provided to attached this to the store lid. Undo the nut

and slip one end over the coachbolt, then pass other end

through the handle and then over the end of the coach

bolt, pulling chain through until it is tight enough. Now re-

attach the nut.

Your Morcott Triple Bin Store is now complete.

We hope that you found your product quick and easy to assemble but if not and you require any further assistance or have

any questions you can contact us by telephone on: 01778 440803

Email: info@rutlandcountygardenfurniture.co.uk www.rutlandcountygardenfurniture.co.uk

This manual suits for next models

Table of contents

Other Rutland County Garden Furniture Outdoor Furnishing manuals