Ryobi 260111130 Operation manual
18 VOLT NICKEL-CADMIUM/
LITHIUM-ION BATTERY CHARGER
OWNER'S OPERATING MANUAL
260111130 (BCL-1800)
.
260111130 manual (SAA).indd A1260111130 manual (SAA).indd A1 1/2/08 10:51:46 AM1/2/08 10:51:46 AM
1. 260111130 Charger
2. Battery Port
3. Green LED
4. Red LED
5. "Key Hole" Hanger
6. Charge Indicator Light
7. Battery Gauge Button
8. Depress Latches to remove Battery Pack
DESCRIPTION
(See Figures 1-3)
Fig. 1
3
41
2
5
Fig. 3
3
8
4
Fig. 2
7
6
260111130 manual (SAA).indd A2260111130 manual (SAA).indd A2 1/2/08 10:51:51 AM1/2/08 10:51:51 AM
1
English
SAFETY INSTRUCTIONS
CAUTION
When using the battery charger, the following
basic safety precautions should be observed for
protection against electric shock, danger of injury
and burns.
Please read and observe these instructions before using
the device.
nBefore using the device check that the mains cable
and mains plug are not damaged.
nThe device must not be damp, neither should it be
used in a damp environment.
nDo not use the device if it has suffered any heavy
shock or jolting, or is damaged in any other way.
nDue to the heat generated during charging,
the battery charger should not be operated on a
combustible surface/in an inflammable environment.
nDo not cover the ventilating slits
nNever disassemble the device yourself. Danger of
an electric shock or fire could be caused by improper
reassembly.
nPull the plug of the battery charger out of the socket
when it is not in use or when cleaning it.
nOnly use extension cable that is approved and
technically in perfect condition.
nDuring operation provide sufficient ventilation.
Malfunction during charging can be caused by storing
and operating in places where the temperature
exceeds +40°C; this should be avoided. Battery
charging in closed cupboards, near heat sources
(radiators, bright sunshine) etc. causes heat to
accumulate and can damage the device.
nIf the battery is not going to be used for a longer
period, pull the battery off the battery charger and pull
out the mains plug.
nProtect battery contact to avoid a short circuit caused
by metallic object that can cause a fire or explosion!
nDo not rivet or screw any name-plates or signs onto
the device. The protective insulation can thereby
be rendered ineffective. Adhesive labels are
recommended.
nOnly charge original recommended batteries.
nIf the power cord is damaged, it must be replaced by an
Authorised Service Center in order to avoid a hazard.
WARNING
Do not recharge primary cells (non-
rechargeable).
Damage to property/material
Mains voltage must correspond with the voltage
specifications on the device.
nThis appliance is not intended for use by persons
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervi-
sion or instruction concerning use of the appliance
by a person responsible for their safety. Children
should be supervised to ensure that they do not
play with the appliance.
nThis appliance is not intended for use by young
children or infirm persons unless they have been
adequately supervised by a responsible person to
ensure that they do not play with the appliance.
nKeep children and visitors away. Visitors should
wear safety glasses and be kept a safe distance from
work area.Do not let visitors contact tool or extension
cord.
nComplies with AS/NZS 60335.
ASSEMBLY
No assembly required on this product.
SPECIFICATIONS
Battery Voltage Charger Battery No. of cell
Pack Input Capacity for battery
130247015 18 V 240V, 50Hz, 1.7 Ah 15
AC only
130501002 18 V 240V, 50Hz, 2.4 Ah 10
AC only
OPERATION
WARNING
Do not allow familiarity with products to make
you careless. Remember that a careless fraction
of a second is sufficient to inflict serious injury.
260111130 manual (SAA).indd Sec1:1260111130 manual (SAA).indd Sec1:1 1/2/08 10:51:53 AM1/2/08 10:51:53 AM
2
English
OPERATION
WARNING
Always wear safety goggles or safety glasses
with side shields when operating products.
Failure to do so could result in objects being
thrown into your eyes, resulting in possible
serious injury.
WARNING
Do not use any attachments or accessories
not recommended by the manufacturer of this
product. The use of attachments or accessories
not recommended can result in serious personal
injury.
APPLICATIONS
You may use this product for the following purposes:
nCharging compatible Ryobi 18 volt battery packs
CAUTION
If at any point during the charging process none
of the LEDs are lit, remove the battery pack
from the charger to avoid damaging the product.
DO NOT insert another battery. Return the
charger and battery to your nearest service
center for service or replacement.
CAUTION
Charge in a well ventilated area. Do not block
charger vents. Keep them clear to allow proper
ventilation.
BATTERY PROTECTION FEATURES
Ryobi One+ 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life.
If the tool stops during use, release the trigger to reset
and resume operation. If the tool still does not work, the
battery needs to be recharged.
BATTERY GAUGE (Fig. 2)
To display the amount of charge left in the battery, press
and hold the battery gauge button.
nIf the charge indicator light glows green, the battery
pack is fully charged.
nIf it glows yellow, it has a usable charge remaining but
will soon require recharging.
nIf it glows red, the battery requires recharging as
indicated by the battery gauge symbols on top of the
battery.
Note: The LED charge indicator light will not work if
the battery protection feature has caused the battery
pack to stop powering the tool. When the battery pack
resets itself, the LED will again function.
LED FUNCTIONS OF CHARGER (Fig. 3-4)
CHARGER LED WILL BE ON TO INDICATE STATUS
OF CHARGER AND BATTERY PACK:
nRed LED on, Green LED off = Power to charger is on.
nRed LED flashing, Green LED off = Battery is being
tested.
nRed LED flashing, Green LED flashing = Battery is
defective.
nRed LED on, Green LED flashing = Battery is
charging.
nRed LED off, Green LED on = Battery is fully
charged.
CHARGING THE BATTERY PACK
Use only these Ryobi One+ 18 V battery packs with
this charger.
Battery packs for this tool are shipped in a low charge
condition to prevent possible problems. Therefore,
you should charge them until the green LED on the front
of the charger comes on.
Note: The charger will also charge Ryobi One+ 18 V
Ni-Cd battery packs.
CHARGING A COOL BATTERY PACK
If the charger does not charge the battery pack under
normal circumstances, return both the battery pack and
charger to your nearest Authorized Service Center for
electrical check.
nCharge the battery pack only with the charger
provided.
nMake sure the power supply is normal household
voltage, 240V, 50Hz, AC only.
nMake sure the latches on each side of the battery
pack snap into place and the battery pack is secured
in the charger before beginning operation.
nConnect the charger to the power supply.
nPlace the battery pack in the charger aligning raised
rib on the battery pack with the groove in the charger.
260111130 manual (SAA).indd Sec1:2260111130 manual (SAA).indd Sec1:2 1/2/08 10:51:55 AM1/2/08 10:51:55 AM
3
English
OPERATION
nPress down on the battery pack to be sure contacts
on the battery pack engage properly with contacts in
the charger.
Note: After charging is complete, the green LED will
remain on until the battery pack is removed from the
charger or charger is disconnected from the power supply.
nThe battery pack will become slightly warm to the
touch while charging. This is normal and does not
indicate a problem.
nDo not place the charger and battery pack in an area
of extreme heat or cold. They will work best at normal
room temperature.
Note: The charger and battery pack should be placed
in a location where the temperature is more than
10°C but less than 38°C.
nWhen batteries become fully charged, unplug the
charger from the power supply and remove the
battery pack.
nTo remove the battery pack from the charger, depress
the latches on each side of the battery pack.
CHARGING A HOT BATTERY PACK
When using a tool continuously, the batteries in the
battery pack will become hot. You should let a hot battery
pack cool down for approximately 30 minutes before
attempting to recharge.
Note: This situation only occurs when continuous use
of a tool causes the batteries to become hot. It does not
occur under normal circumstances. Refer to "CHARGING
A COOL BATTERY PACK" for normal recharging of
batteries. If the charger does not charge your battery
pack under normal circumstances, return both the battery
pack and charger to your nearest Authorized Service
Center for electrical check.
LED FUNCTION
LED
INDICATOR
BATTERY
PACK
RED
LED
GREEN
LED
ACTION
Power Without
battery
pack
ON OFF Ready to charge
battery pack.
Evaluate Hot
battery
pack
Flashing OFF When battery pack
reaches cooled
temperature,
charger begins fast
charge mode.
Evaluate Cold
battery
pack
Flashing OFF When battery pack
reaches warmed
temperature,
charger begins fast
charge mode.
Deeply
discharged
Flashing OFF Charger pre-
charges battery
until nomal voltage
is reached, then
begins fast charge
mode.
Defective Defective Flashing Flashing Battery pack
or charger is
defective.
If defective, try to repeat the conditions a second
time by removing and reinstalling the battery pack. If
the LED status repeats a second time, try charging a
different battery.
If a different battery charges normally, dispose of the
defective pack (see Maintenance section).
If a different battery also indicates "Defective," the
charger may be defective.
Charging Fast
charging
ON Flashing
Fast charging is
complete; charger
maintains charge
mode.
Full OFF ON
_
_
Evaluate
260111130 manual (SAA).indd Sec1:3260111130 manual (SAA).indd Sec1:3 1/2/08 10:51:56 AM1/2/08 10:51:56 AM
4
English
MAINTENANCE AND REPAIRS
Risk of injury
Service, testing and repairs should only be
carried out by authorised service centres.
We recommend our customer service department or
authorised service centres.
STORAGE
Store your charger in a cool dry place between 10 &
25°C. It is not recommended to leave it in a cold works
van overnight. Ensure no metal filings or swarf can fall
into the vents during storage, as this may cause serious
injury when it is next used.
260111130 manual (SAA).indd Sec1:4260111130 manual (SAA).indd Sec1:4 1/2/08 10:51:57 AM1/2/08 10:51:57 AM
4%#(42/.)#).$5342)%3!5342!,)!049,)-)4%$
'5!2!.4%%
!".
#ONTACT DURING NORMAL BUSINESS HOURS
!5#+,!.$ #LEMOW $RIVE -T 7ELLINGTON .:
#ONTACT DURING NORMAL BUSINESS HOURS
!,,!5342!,)!.%.15)2)%34%,
7%34!5342!,)!.%.15)2)%34%,
!
0URCHASED&ROM
DDRESS /F $EALER
0RESENT 4HIS &ORM 7ITH 9OUR 0URCHASE $OCKET 7HEN 'UARANTEE 3ERVICE )S 2EQUIRED
4EL &AX WWWRYOBICOMAU
4EL &REE #ALL &AX WWWRYOBICONZ
&OR YOUR RECORD AND TO ASSIST IN ESTABLISHING DATE OF PURCHASE NECESSARY FOR INGUARANTEE SERVICE
PLEASE KEEP YOUR PURCHASE DOCKET AND THIS FORM COMPLETED WITH THE FOLLOWING PARTICULARS
4HIS 'UARANTEE &ORM 3HOULD "E 2ETAINED "Y 4HE #USTOMER !T !LL 4IMES
$ATE -ODEL .O 3ERIAL .O
39$.%9"UILDING"2OSEHILL)NDUSTRIAL%STATE3HIRLEY3TREET2OSEHILL.37
4%#(42/.)#).$5342)%3!5342!,)!049,)-)4%$
4%#(42/.)#).$5342)%3.:,)-)4%$
3UBJECT TO THE GUARANTEE CONDITION BELOW THIS 2YOBI
TOOLHEREINAFTERCALLEDhTHEPRODUCTvISGUARANTEEDBY
4%#(42/.)# ).$5342)%3 !5342!,)! 049
,)-)4%$HEREINAFTERCALLEDhTHE#OMPANYvTOBEFREE
FROMDEFECTSINMATERIALORWORKMANSHIPFORAPERIODOF
MONTHSFROMTHEDATEOFORIGINALPURCHASECOVERING
BOTHPARTSANDLABOUR5NDERTHETERMSOFTHISGUARAN
TEETHEREPAIRORREPLACEMENTOFANYPARTSHALLBETHE
OPINION OF THE #OMPANY OR ITS AUTHORISED 3ERVICE
CENTRE3HOULDSERVICEBECOMENECESSARYDURINGTHE
WARRANTY PERIOD THE OWNER SHOULD CONTACT THE
CUSTOMERSERVICE(%,0,).%ORCONTACT
THERETAILERFROMWHOMTHEPRODUCTWASPURCHASED
)NORDERTOOBTAINGUARANTEESERVICETHEOWNERMUST
PRESENTTHESALESDOCKETAND'UARANTEE#ERTIFICATETO
CONFIRMDATEOFPURCHASE4HISPRODUCTISSOLDBYTHE
DEALER OR 3ERVICE CENTRE AS PRINCIPAL AND THE DEALER
HAS NO AUTHORITY FROM THE #OMPANY TO GIVE ANY
ADDITIONALGUARANTEEONTHE#OMPANYSBEHALFEXCEPT
ASHEREINCONTAINEDORHEREINREFERREDTO
'UARANTEE#ONDITIONS
4HISGUARANTEEONLYAPPLIESPROVIDEDTHATTHE0RODUCT
HASBEENUSEDINACCORDANCEWITHTHEMANUFACTURERS
RECOMMENDATIONSUNDER NORMALUSE ANDREASONABLE
CAREINTHEOPINIONOFTHE#OMPANYANDSUCH
GUARAN
TEE DOES NOT COVER DAMAGE MALFUNCTION OR FAILURE
RESULTING FROM MISUSE NEGLECT ABUSE OR USED FOR A
PURPOSEFORWHICHITWASNOTDESIGNEDORISNOTSUITED
ANDNOREPAIRSALTERATIONSORMODIFICATIONSHAVEBEEN
ATTEMPTEDBYOTHERTHANAN!UTHORISED3ERVICECENTRE
4HISGUARANTEEWILLNOTAPPLYIFTHETOOLISDAMAGEDBY
ACCIDENTORIFREPAIRSARISEFROMNORMALWEARANDTEAR
4HE#OMPANYACCEPTSNOADDITIONALLIABILITYPURSUANT
TOTHISGUARANTEEFORTHECOSTSOFTRAVELLINGORTRANSPOR
TATIONOFTHE0RODUCTORPARTSTOANDFROMTHESERVICE
DEALEROR3ERVICECENTRESUCHCOSTSARENOTINCLUDED
IN THISGUARANTEE
#ERTAINLEGISLATIONINCLUDINGTHE4RADE0RACTICES
!CT AS AMENDED AND OTHER STATE AND
TERRITORIALLAWSGIVERIGHTSTOTHEBUYERANDIMPOSE
LIABILITYONTHESELLERINCERTAINCIRCUMSTANCES.OTHING
HEREINSHALLHAVETHEEFFECTOFEXCLUDINGRESTRICTINGOR
MODIFYING ANY CONDITION GUARANTEE RIGHT OR LIABILITY
IMPOSED TO THE EXTENT ONLY THAT SUCH EXCLUSION
RESTRICTION OR MODIFICATION WOULD RENDER ANY TERM
HEREINVOID
260111130 manual (SAA).indd Sec1:5260111130 manual (SAA).indd Sec1:5 1/2/08 10:51:58 AM1/2/08 10:51:58 AM
This manual suits for next models
1
Table of contents
Other Ryobi Batteries Charger manuals
