SAFAVIEH COUTURE Zinnia SFV5741A User manual

The legs and hardware are located inside the door
CARE AND MAINTENANCE
Spot clean using a mild water-free solvent. Only a professional cleaner should undertake a
complete overall cleaning.
The use of steam or water-based cleaners may cause excessive shrinking or staining.
NOTICE
* Please make sure that you have all parts indicated before you begin assembly of this item
* This item should be assembled on a soft surface to prevent scratching the finish during
assembly
* This item may require periodic tightening
H3 Allen key 4 mm
1X
4X
Flat washer 16 mm
Allen bolt 25x6 mm
A
B
H1
H2
Cabinet
Leg
6X
6X
1X
PIECE QUANTITY
DESCRIPTION PICTURE
Item# NST9008A
Product dimensions: 55.1"L* 13.7"W*17.7"D
WARNING
Weight Capacity - 110 LBS
Warning : Do not stand on Table
Warning : Do not over torque bolts.
Item# SFV5741A
Product dimensions: 55.1"W* 13.7"D*17.7"H
WARNING
Weight Capacity - 110 LBS
Warning : Do not stand on TVC
Warning : Do not over torque bolts.
NOTICE
* Please make sure that you have all parts indicated and are in good condion before you begin assembly
of this item. Refer to part list and hardware list below for guidance .
* This item should be assembled on a so surface to prevent scratching the finish during assembly.
* This item may require periodic ghtening.
* If you are having difficulty, our friendly customer care team is always here to help . Please
email [e-mail]
* Before beginning assembly of product , make sure all parts are present . Compare parts with parts
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly me : 10 minutes
* Tools Required for Assembly (included): Allen key
CARE AND MAINTENANCE
PREPARATION
contents list and hardware contents list.
Part List and Hardware List
Hw3 Allen key
1X
2X
Flat washer 16 x 8 mm
Allen bolt 6 X 1 X 25mm
A
B
Hw1
Hw2
Cabinet
Leg
6X
6X
1X
PIECE DESCRIPTION PICTURE QUANTITY
*For cleaning surface of wood , dampen a cloth with diluted solvent or cleaning soluon and gently
rub over a small area at a me. Finally wipe the area with clean dampened cloth to remove any cleanser.
*Do not keep hot items like coffee mugs, hot iron etc. directly on surface.

Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list.
If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 15 minutes.
Tools Required for Assembly (included): Allen Key
PREPARATION
A
B
H3
H1
H2
6x
B
A
B
B
The legs and hardware are located Inside the door
STEP1 OPEN THE ZIPPER ON THE
INSIDE OF THE DOOR AND TAKE
OUT LEGS AND HADWARE.
STEP2 PLACE THE TVC (A)
UPSIDE DOWN AS SHOWN.
STEP4 INSERT ALLEN BOLT (H1)
WITH WASHER (H2) AND TIGHTEN
WITH ALLEN KEY (H3).
STEP5 FLIP THE TVC
UPSIDE.
STEP3 ALIGN THE LEGS (B) WITH
THE POSITION ON THE BOTTOM
OF TVC (A).
PREPARATION
* Before beginning assembly of product , make sure all parts are present . Compare parts with parts
* If any part is missing or damaged, do not aempt to assemble the product.
* Esmated Assembly me : 10 minutes
* Tools Required for Assembly (included): Allen key
contents list and hardware contents list.
* If you are having difficulty, our friendly Customer Care team is always here to help. Please email [e-mail]
Leg
STEP1
Unwrap the legs & take out legs.
Hardware
Open the hardware pouch & take out hardware.
STEP2
Place the TVC upside down on a clean surface.
Align legs on both sides of TVC as per side holes
present on either side of TVC.
STEP3
Put the washer on the Bolt in the order shown in
picture.
STEP4
Insert Allen Bolt (Hw1) with Washer (Hw2)
ghten with Allen Key (Hw3).Don’t over ghten.
Hw2 Hw1
Hw2
Hw1
Hw3
STEP5
Repeat step 4 for, other side leg, flip the TVC upright with help.
Hw2
Hw1
Hw3
B
A
B

Grids Surface
STEP6
The unit needs to be secured against wall using p an p kit. Please
Consult your local hardware store to get advice of appropriate screw and
Fischer according to your wall type.
Drill pre-holes on wall as shown in fig(1) for the p protector. Repeat
STEP7
the step with same distance of both p protector aached in step. Insert fischer
to each hole on the wall using hammer as shown in fig(2) .
Secure the Tip Protector using Screw as shown in fig(3).
Make a loop by inserng the provided Fastener / Cable es into both p
protector on wall and on backside of product, with the grids surface facing
inside of loop as shown in fig(4).
Repeat on the other side.
Fasten the cable es unl posion of product as close as possibleto wall as
5
shown in fig(5).