SAGEMCOM D790 User manual

D
7
90
-
D
7
90A
QUI
C
K
S
T
A
RT
G
UI
DE
EN
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 1 Jeudi, 1. août 2013 9:11 09

GIR 253536463B D790-D790A_Sagemcom_EN.book Page 2 Jeudi, 1. août 2013 9:11 09

3
Dear customer,
You have just acquired a new generation Sagemcom telephone. Thank you for placing your confidence in us.
This device has been manufactured with the utmost care.
If you should have difficulties in operating it, we recommend that you consult this quick start guide.
This product follows a strategy of continuous development. We reserve the right to make changes, modifications
and improvements without notice to the products described in this quick start guide.
To operate the device safely and easily, please read carefully the paragraph “Recommendations and safety
instructions”, page 4.
The CE label confirms that the product complies with the 1999/5/EC regulations of the European Union
Parliament regarding wireless systems and telecommunications.
The declaration of compliance may be looked up on the www.sagemcom.com website section
«Support», or can be obtained from the following address:
Sagemcom Broadband SAS
250, route de l'Empereur
92848 Rueil-Malmaison Cedex - France
Copyright © Sagemcom Broadband SAS - All rights reserved - Sagemcom is a registered trademark.
You can also find the complete user guide on the following website: www.sagemcomdigital.co.uk
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 3 Jeudi, 1. août 2013 9:11 09

4
Recommendations and safety
instructions
For safety reasons, never put the handset in the base station
without the battery inserted or without the lid on the battery
compartment as this could cause an electric shock.
To avoid damaging your handset/base, only use certified
rechargeable batteries NiMH 1.2 V 650 mAh, never use
non-rechargeable batteries. Insert the batteries in the
handset/base battery compartment respecting polarity.
Only use the power unit supplied and connect it to the
electricity mains in accordance with the installation
instructions in this user manual and the details on the sticker
regarding voltage, electrical current and frequency. As a
precaution if there is a risk of danger, the power plug can be
pulled out to disconnect the 230 volt power supply.
Therefore the sockets should be near the device and easily
accessible.
Do not install your DECT telephone in a damp environment,
such as a bathroom, washroom, kitchen etc, and not within
1.50 meters of a source of water or outside. This device is
designed for use in temperatures of between 5 °C and 45 °C.
Your DECT telephone has a range of approx. 50 meters
indoors and up to 300 meters outdoors. The range can be
affected by the proximity of metal objects, such as a
television and electrical devices.
Zones without reception may appear owing to elements in
the building. This can cause brief interruptions in the
conversation, caused by faulty transmission. Areas without
reception may appear because of construction peculiarities.
This may cause brief interruptions in conversation, due to
poor transmission.
Certain medical equipment and highly-sensitive machines or
security systems may be affected by the transmission power
of the telephone. In these cases we recommend adhering to
the safety information.
In regions greatly affected by electrical storms we
recommend that you protect your telephone circuit with a
special fixture for excess voltage.
Your D790 has anti-skid pads that should leave no traces on
your furniture and ensure stability. However, given the wide
variety of finishes used by furniture manufacturers, traces
may appear on surfaces in contact with the parts of your
D790. Sagemcom Broadband SAS decline all responsibility
in any such cases of damage.
Do not attempt to remove screws or open the appliance. It
does not contain any user-replaceable parts.
The used battery must be disposed of in line with the
recycling regulations in this user manual.
This product is intended to be connected to the public
analogue telephone network of any British and Irish network
operator. Should you experience any problems, contact your
nearest specialst dealer or the Sagemcom Support Team on
0845 0900 316.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 4 Jeudi, 1. août 2013 9:11 09

5
Discover...
Your phone
The pack
Make sure that your pack contains the following items:
In the case of purchasing a pack DUO or TRIO, you will find in addition:
The base
a D790 or D790A base
according to the model
a handset
an AC power supply
a handset charger
a telephone
connection cord
a quick
installation guide
a handset charger
DUO
- or -
TRIO
a handset
Caption Description
1
Indicator light
2
Telephone socket
3
Power socket
4Button
Paging / Pairing
:
Short press
: paging of handsets
Long press
: pairing of handsets
1
23
4
Indicator light operation :
Fixed for 10 seconds: base startup.
Fast flashing: the base is in pairing mode.
Blinking means: handset paging.
Slow flashing: handset on line.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 5 Jeudi, 1. août 2013 9:11 09

6
The handset
1Loudspeaker
2Screen
3Programmable / cancel shortcut key.
4Browsing through the menus.
5Hang up key
•Short press: hang up (during call) / return to main
menu.
•Long press: switch off the handset.
6Alphanumeric keyboard.
7# key
•Long press: switch off the microphone (during call).
8Phonebook access key
9Microphone
10 Hands-free key
11 Star key
Long press: unlock/lock the keyboard.
12 Pick-up / Hands-free key
•Long press: switch on the handset.
•Short press: pick-up call.
13 Programmable / confirm shortcut key.
14 Indicator light.
14
4
3
13
1
2
5
6
8
9
12
7
11
10
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 6 Jeudi, 1. août 2013 9:11 09

7
Install...
Connect the base
Take the base and turn it over:
1Take the telephone connecting cord, plug the phone jack into its
socket.
2Connect the other end of the cord to the telephone wall outlet.
3Take the power adapter assembly. Connect the power adapter
cord to the underside of the base.
4Connect the power adapter to the wall power socket.
5Position the base in its final location.
Handset set-up
1Connect the power adapter of the charger to the mains socket.
2The batteries are already inserted in the handset. To start using
your handset, simply remove the plastic tab by pulling on it firmly
in the direction of the arrow.
3The screen will turn on.
4An information screen presents the current language used.
5Select the language using and keys. Press Valid..
6An information screen asks you to choose the country where you
will use your telephone.
7Select the country using and keys. Press Valid..
8Place your handset on its charger and fully charge the batteries.
A beep sounds when you place the handset on the charger.
The battery charging icon moves to inform you that charging is in
progress. The icon will stop moving when the batteries are fully charged.
Before making any connections, check the safety instructions at
the start of this guide page 4.
2
1
3
4
1321
15 H
HD
13/12 -1- 14:05
13/12 -1- 14:05
13/12 -1- 14:05
HD
HD
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 7 Jeudi, 1. août 2013 9:11 09

8
The screen
THE ICONS DISPLAYED
In standby mode or during use, your phone screen informs you of your
phone’s current state through icons, and in particular:
1Status icons: Indicates your phone’s current state.
2Information area:
•placed on the charger: the current time is displayed,
•off-hook: handset number, the date and time are displayed.
3Action icons: displays the following when the phone is:
•placed on the charger: browser actions and the confirm key,
•off-hook: menus associated with programmable keys.
To ensure optimum charging, leave the handset on the charger for
at least 15 hours when using the phone for the first time. During
charging, the batteries may heat up. This is quite normal and
perfectly safe.
If you do not obtain radio contact with your base, check the
electrical connections to your base.
13/12 -1- 14:05
TAM
Calls
2
1
3
Battery charge condition Speakerphone on
Phone in conversation
mode Low transmission
Secret mode on DECT signal
Answering machine on or
new message(s) on your
answering machine or
voicemail
Alarm on
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 8 Jeudi, 1. août 2013 9:11 09

9
Browse Menus...
Browser
This browser allows you to quickly access menus and change
your settings easily. It points in two directions.
When choosing menus, press the top or the bottom of the
browser to access the previous or next menu.
Press
Valid.
to confirm your selection.
During a call, press the top of the browser to increase the volume or the
bottom to decrease it.
Programmable keys
Your phone has two "programmable" , keys allowing you to
associate a shortcut to the menus you use most. This shortcut can then be
accessed from your phone's home screen.
These keys are also used to confirm or cancel an action in a menu.
Communicate...
Managing a call
Making a call
METHOD 1
1Dial your contact’s number.
2Press the key , a beep sounds.
METHOD 2
1Press the key .
2Dial your contact’s number, a beep sounds.
At the end of the call, press the handset key and replace the handset
on its charger.
Receiving a call
1Press the key to take the call.
2At the end of the call, press the handset key and replace the
handset on its charger, a beep sounds.
A complete user booklet is available on our website
www.sagemcomdigital.co.uk
. It includes all your phone's menus.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 9 Jeudi, 1. août 2013 9:11 09

10
Options during a call
You can use the following options during a call:
Enable/Disable loudspeaker (handsfree mode)
A confirmation screen is displayed, only if it is enabled via the "Call in
progress" menu.
Adjusting the volume
•To increase the volume, press .
•To decrease the volume, press .
Enabling/Disabling the secret mode
The secret mode allows you to temporarily mute the line so that you are not
heard by the caller. Once enabled, the
SECRET
message and the icon
are displayed.
Press
Exit
to disable secret mode.
Creating a phonebook entry
Specify the required information by confirming at each step:
1NEW NAME?: enter your contact’s name,
2NEW NUMBER?: enter your contact’s number,
3HOME, WORK, MOBILE or FAX: select the number type.
4TRNSF. MODE?:
•Press Yes to transfer your contact to other handsets registered
on the base (for further details refer to paragraph " Transferring
entries from one handset to another" on the
complete user guide
available on our website
www.sagemcomdigital.co.uk
.
).
•Press No to skip transfer operation and save the entry to the
phonebook.
Locating your handset (paging)
If you have misplaced your handset, press the key on the rear of your
phone's base. The handset will ring (only if it is switched on).
Listen and Record...
(model D790A)
Enabling/disabling the answering machine
When the answering machine is enabled, the icon is displayed on the
screen.
Answering machine message
Recording your outgoing message
Confirm the instructions on the screen.
or (during a call)
Menu during a call > HANDSFREE > Activ. or Disable
(during a call)
(during a call)
Menu during a call > SECRET > Activ.
When your battery charging icon displays the minimum, the
handsfree mode is unavailable until the battery has been
recharged.
Menu > PHONEBOOK > < New >
Menu > ANSW.MACH > ANSWERING MODE > ON or OFF
Menu > ANSW.MACH > OUTGOING MESS. > CHANGE
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 10 Jeudi, 1. août 2013 9:11 09

11
Listening to your outgoing message
The currently used outgoing message is played.
Erasing your outgoing message
Confirm the instructions on the screen.
Messages
Listening to your messages
The messages are played in chronological order (from oldest to newest).
At the end of the last message, the answering machine will stop
automatically.
Managing your messages
When playing back messages, press the following buttons:
Set up your telephone...
Associating a new handset
You can associate other handsets with your base by following a pairing
process.
FROM AHANDSET REGISTERED ON YOUR BASE:
To enable pairing mode on your base from a registered handset:
OR FROM THE BASE:
To enable the pairing mode, press and hold
(on the rear of the
base).
THEN FROM THE NEW HANDSET:
Enable pairing mode on the handset.
Menu > ANSW.MACH > OUTGOING MESS. > PLAY
Menu > ANSW.MACH > OUTGOING MESS. > DELETE
Menu > ANSW.MACH > MESSAGES > PLAY
To... From the handset
Go on to the next message 1 press
Return to the start of the message 1 press
Return to the previous message 2 presses
Pause/Resume Playback 1 press
Delete the message being played 1 press
Menu > SETTINGS > ADVANCED SET. > SET BASE >
REGISTR.MODE
Menu > SETTINGS > ADVANCED SET. > SET HANDSET >
REGISTRATION
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 11 Jeudi, 1. août 2013 9:11 09

12
Changing the ringing tone
You can change the ring tone of:
•outside calls,
•calls between handsets (intercom).
Scroll through the pre-recorded ring tones and confirm.
Setting the date and the time
1Enter the DATE: in as DD/MM/YY.
2Enter the TIME: starting with the hours and then the minutes.
3Confirm your entry.
Menu > RING TONE > EXTERNAL CALL or INTERNAL CALL
Menu > SETTINGS > DATE/TIME
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 12 Jeudi, 1. août 2013 9:11 09

13
Menu tree structure
PHONEBOOK
Option
< New >
VIEW
EDIT
ADD NUMBER
NEW ENTRY
DELETE
TRANSMIT
Menu during a call
HANDSFREE
CALL TRANSFER (**)
SECOND CALL
PHONEBOOK
CALLS
SECRET
RECORD (*)
Simple call
CALLS
INCOMING CALLS
OUTGOING CALLS
EVENTS
ACCESSORIES
ALARM
ROOM MONITOR.
RING TONE
EXTERNAL CALL
INTERNAL CALL
BEEPS
SILENT MODE
(*) Only for the answering machine model (D790A).
(**) Only if two handsets are registered on the same same base.
SETTINGS
PROGRAM KEYS
DATE/TIME
CONTRAST
AUTO HANG UP
AUTO PICKUP
VOICE BOX No
LANGUAGE
KEYPAD LOCK
RESTRICTION
ADVANCED SET.
SET HANDSET REGISTRATION
BASE PRIORITY
RESET HANDSET
PERSON.REGISTR
HANDSET NAME
REGISTR.MODE
RESET BASE
DELETE HANDSET
RENAME BASE
INTRUSION
SET BASE
SET LINE NETWORK TYPE
DIAL
FLASHING
PABX PREFIX
COUNTRY
CHANGE CODE
ANSW.MACH (*)
MESSAGES PLAY
DELETE OLD
PLAY
CHANGE
DELETE
REMOTE CODE
MODE ENREG.
NO OF RINGS
ANSWERING MODE
OUTGOING MESS.
SETTINGS
SWITCH
3-PARTY CONF
HANDSFREE
PHONEBOOK
CALLS
SECRET
RECORD (*)
HANGING UP
Second call
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 13 Jeudi, 1. août 2013 9:11 09

14
Environment
Environmental protection and sustainable development is an important priority for Sagemcom. Sagemcom has a policy of using
environmentally- friendly systems and makes environmental protection an essential part of the life-cycle of its products – from
manufacturing, to installation, operation and disposal.
Packaging
The logo (green point) on the packaging means that a fee is paid to an authorised national organisation to improve
packaging recycling and the recycling infrastructure.
Follow the local sorting regulations for this type of waste product in order to improve recycling.
Batteries
If your product contains batteries, they must be disposed of at the designated collection points.
The product
The crossed out dustbin displayed on the product signifies that it belongs to the electrical and electronic equipment group.
The European regulations request you to carry out your own selective recycling collection at:
-the sales outlet when you buy a similar new device.
-the collection points available in your area (recycling centres, sorting points, etc).
This means you participate in the recycling and valorisation of used electric and electronic goods which would otherwise have a
negative impact on the environment and health.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 14 Jeudi, 1. août 2013 9:11 09

15
Guarantee
Terms and Conditions for United Kingdom & Ireland only
In order to apply the guarantee, or for technical assistance, you should contact the Sagemcom Helpdesk (
0845 0900 316
) or the
retailer you purchased your equipment from.
Please make sure that you use your equipment only for the purpose for which it was designed and under normal usage conditions.
Sagemcom do not accept any liability for the equipment if used outside the frame of its original designed purpose or any
consequence that may arise from this usage.
Should any malfunction arise, the Sagemcom Helpdesk or your retailer will advise you how to proceed.
A) General Guarantee conditions
Sagemcom undertakes to remedy by repair or exchange at its own convenience, free of charge for labour and replacement parts,
any defects in the equipment during the guarantee period of 12 (twelve) months or 3 (three) months for accessories, from the date
of original invoice of the Equipment, where those defects are a result of faulty workmanship.
Unless the customer has concluded with Sagemcom a maintenance contract in respect of the equipment which specifically provides
for repairs to be carried out at the customer`s premises, the repairs will not be carried out on the equipment at the customer
premises.
The customer must however return the defective equipment at his/her own expense, to the address supplied by the Sagemcom
Helpdesk or by the retailer.
In the case that a product needs to be sent in for a repair, it must always be accompanied by a proof of purchase (which is not
altered, written on or in any way made illegible) showing that the product is still under guarantee. In the case that no proof of
purchase is enclosed, the Sagemcom repair centre will use the production date as its reference for establishing the guarantee status
of the product.
Apart from all legal obligatory rules, Sagemcom, do not give any Guarantee, either implicit or explicit which is not set force in the
present section, and can not be held responsible for any direct or indirect, material or immaterial damage, either in or out of the
frame of the present guarantee.
If any provision of this guarantee shall be held to be in whole or in part invalid or illegal due to an obligatory rule applicable to
consumers pursuant to their national legislation, such invalidity or illegality shall not impair or affect the remaining provisions or parts
of this guarantee.
This guarantee does not affect the Customer statutory rights.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 15 Jeudi, 1. août 2013 9:11 09

16
B) General Guarantee conditions
Sagemcom shall have no liability under the guarantee in respect of:
• Damage, defects, breakdown or malfunction due to one or more of the following:
-Failure to properly follow the installation process and instructions for use
-An external cause to the equipment (including but not limited to: lightening, fire, shock, vandalism, inappropriate
conditions of electrical network or water damage of any nature)
-Modifications made without the written approval of Sagemcom
-Unsuitable operating conditions, particularly of temperature and humidity
-Repair or maintenance of the equipment by persons not authorised by Sagemcom
• Wear and tear from normal daily use of the equipment and its accessories
• Damage due to insufficient or bad packaging of equipment when returned to Sagemcom
• Usage of new versions of software without the previous approval of Sagemcom
• Work on any equipment or software modified or added without the prior written consent of Sagemcom
• Malfunctions not resulting from the Equipment or from software installed in user workstations for the purpose of use of
the equipment.
Communication problems related to an unsuitable environment including:
-Problems related to access and/or connection to the Internet such as interruptions by access networks or
malfunction of the line used by the subscriber or his correspondent
-Transmission faults (for example poor geographical coverage by radio and TV transmitters, interference or poor line
quality)
-Local network faults (wiring, servers, workstations) or the failure of the transmission network (such as but not limited
to interferences, fault or poor quality of the network)
-Modification of the parameters of the cellular or broadcast network carried out after the sale of the Product
• Normal servicing (as defined in the user guide supplied with the equipment) as well as malfunctioning due to servi-
cing not being carried out. Servicing costs are in any event always borne by the customer.
Malfunctions resulting from the usage of products, consumables or accessories not compatible with the equipment.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 16 Jeudi, 1. août 2013 9:11 09

17
C) Out of Guarantee Repairs
In the cases set forth in B) as well as after expiry of the guarantee period, the customer must ask the Authorised Sagemcom Repair
Centre for a cost estimation prior to work being carried out. In such cases, the repair and delivery costs will be invoiced to the
customer.
The foregoing shall apply unless otherwise agreed in writing with the customer and only for the United Kingdom and Ireland.
www.sagemcomdigital.co.uk
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 17 Jeudi, 1. août 2013 9:11 09

GIR 253536463B D790-D790A_Sagemcom_EN.book Page 18 Jeudi, 1. août 2013 9:11 09

GIR 253536463B D790-D790A_Sagemcom_EN.book Page 19 Jeudi, 1. août 2013 9:11 09

Sagemcom Broadband SAS
Headquarters: 250, route de l'Empereur
92848 Rueil-Malmaison Cedex - France
Tel. +33(0)1 57 61 10 00 - Fax: +33(0)1 57 61 10 01
www.sagemcom.com
253536463B - 08/2013
All rights reserved. The information and specifications included are subject to change without prior notice.
Sagemcom Broadband SAS tries to ensure that all information in this document is correct, but does not accept
liability for error or omission. Non contractual document. All trademarks are registered by their respective
owners. Simplified joint stock company - Capital 35 703 000 €- 518 250 360 RCS NANTERRE.
GIR 253536463B D790-D790A_Sagemcom_EN.book Page 20 Jeudi, 1. août 2013 9:11 09
Other manuals for D790
1
This manual suits for next models
1
Table of contents
Other SAGEMCOM Telephone manuals

SAGEMCOM
SAGEMCOM D780A User manual

SAGEMCOM
SAGEMCOM C95 User manual

SAGEMCOM
SAGEMCOM D750 User manual

SAGEMCOM
SAGEMCOM D770 User manual

SAGEMCOM
SAGEMCOM C120 ECO User manual

SAGEMCOM
SAGEMCOM D790 User manual

SAGEMCOM
SAGEMCOM SIXTY User manual

SAGEMCOM
SAGEMCOM C112 ECO User manual

SAGEMCOM
SAGEMCOM SIXT4 User manual

SAGEMCOM
SAGEMCOM C91 User manual