Samsung S5PV210 Guide

S5PV210_HARDWARE DESING GUIDE REV 1.0
Hardware Design
Guide
S5PV210
RISC Microprocessor
FEB 8, 2010
REV 1.0

S5PV210_HARDWARE DESING GUIDE REV 1.0
2
Important Notice
The information in this publication has been carefully
checked and is believed to be entirely accurate at the
time of publication. Samsung assumes no
responsibility, however, for possible errors or
omissions, or for any consequences resulting from the
use of the information contained herein.
Samsung reserves the right to make changes in its
products or product specifications with the intent to
improve function or design at any time and without
notice and is not required to update this
documentation to reflect such changes.
This publication does not convey to a purchaser of
semiconductor devices described herein any license
under the patent rights of Samsung or others.
Samsung makes no warranty, representation, or
guarantee regarding the suitability of its products for
any particular purpose, nor does Samsung assume
any liability arising out of the application or use of any
product or circuit and specifically disclaims any and all
liability, including without limitation any consequential
or incidental damages.
"Typical" parameters can and do vary in different
applications. All operating parameters, including
"Typicals" must be validated for each customer
application by the customer's technical experts.
Samsung products are not designed, intended, or
authorized for use as components in systems
intended for surgical implant into the body, for other
applications intended to support or sustain life, or for
any other application in which the failure of the
Samsung product could create a situation where
personal injury or death may occur.
Should the Buyer purchase or use a Samsung product
for any such unintended or unauthorized application,
the Buyer shall indemnify and hold Samsung and its
officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs,
damages, expenses, and reasonable attorney fees
arising out of, either directly or indirectly, any claim of
personal injury or death that may be associated with
such unintended or unauthorized use, even if such
claim alleges that Samsung was negligent regarding
the design or manufacture of said product

S5PV210_HARDWARE DESING GUIDE REV 1.0
.
S5PV210 RISC Microprocessor
Hardware Design Guide, Revision 1.0
Copyright ©2010 Samsung Electronics Co., Ltd.
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in
any form or by any means, electric or mechanical, by photocopying, recording, or otherwise, without the prior
written consent of Samsung Electronics.
Samsung Electronics Co., Ltd.
San #24 Nongseo-Dong, Giheung-Gu
Yongin-City, Gyeonggi-Do, Korea 446-711
TEL : (82)-[phone]
FAX : (82)-[phone]
Home Page: http://www.samsungsemi.com
Printed in the Republic of Korea

S5PV210_HARDWARE DESING GUIDE REV 1.0
4
Revision History
Revision No Description of Change Refer to Author(s) Date
1.0 - First release version Feb 08, 2010

S5PV210_HARDWARE DESING GUIDE REV 1.0
5
Table of Contents
1. OVERVIEW...............................................................................................................................................8
1.1. S5PV210 Pin Information........................................................................................................................... 8
2. BALL NUMBER ASSIGNMENT .............................................................................................................63
3. POWER...................................................................................................................................................71
3.1. Pin Power Domain....................................................................................................................................71
3.2. Recommend Operating Conditions........................................................................................................73
3.3. Circuit design without level shifter........................................................................................................75
3.4. Power On/Off Sequence..........................................................................................................................76
3.5. Pin configuration guide in Sleep mode .................................................................................................78
4. SYSCON .................................................................................................................................................79
4.1. Signal Description....................................................................................................................................79
4.2. Booting Option.........................................................................................................................................81
4.3. Feature of the IROM Boot mode.............................................................................................................82
4.4. Clock..........................................................................................................................................................83
5. MEMORY SUBSYSTEM.........................................................................................................................85
5.1. Signal Description....................................................................................................................................85
5.2. TQ : Temperature Indicator.....................................................................................................................85
5.3. PCB LAYOUT GUIDELINES FOR MEMORY...........................................................................................85
6. SROM CONTROLLER............................................................................................................................88
6.1. Signal Description....................................................................................................................................88
6.2. SRAM/ROM Interface Examples .............................................................................................................89
7. ONENAND CONTROLLER.....................................................................................................................90
7.1. Signal Description....................................................................................................................................90
7.2. Circuit Diagram Example.........................................................................................................................91
8. NAND FLASH CONTROLLER ...............................................................................................................92
8.1. Signal Description....................................................................................................................................92
9. CF CONTROLLER..................................................................................................................................94
9.1. CFCON feature .........................................................................................................................................94
9.2. Signal Description....................................................................................................................................94
9.3. CF 1-slot operation guide........................................................................................................................95
9.4. CF 2-slot operation guide........................................................................................................................96
10. PWM TIMER........................................................................................................................................97

S5PV210_HARDWARE DESING GUIDE REV 1.0
6
10.1. Overview................................................................................................................................................97
10.2. Signal Description................................................................................................................................97
11. UART...................................................................................................................................................98
11.1. Signal descriptoin ................................................................................................................................98
12. IIC-BUS INTERFACE ..........................................................................................................................99
12.1. Pin Description .....................................................................................................................................99
12.2. Equation of the pull-up resistor value..............................................................................................100
13. SPI.....................................................................................................................................................101
13.1. Signal Description..............................................................................................................................101
13.2. EXTERNAL Loading Capacitance.....................................................................................................101
13.3. SPI Maximum Speed ..........................................................................................................................101
14. USB HOST.........................................................................................................................................102
14.1. Singnal Description............................................................................................................................102
14.2. Power Domain.....................................................................................................................................102
14.3. Circuit Diagram Example...................................................................................................................102
14.4. USB SIGNAL ROUTING......................................................................................................................103
15. USB 2.0 HS OTG...............................................................................................................................105
15.1. Signal Descriptoin..............................................................................................................................105
15.2. Power Domain.....................................................................................................................................105
16. MODEM INTERFACE........................................................................................................................107
16.1. Signal Description..............................................................................................................................107
16.2. Pin Connection Example ...................................................................................................................107
17. SD/MMC HOST CONTROLLER........................................................................................................109
17.1. Signal Description..............................................................................................................................109
17.2. Muxed Signal usage...........................................................................................................................109
18. TSI .....................................................................................................................................................111
18.1. Signal Description..............................................................................................................................111
18.2. Connection Example..........................................................................................................................111
19. DISPLAY CONTROLLER..................................................................................................................112
19.1. Signal Description..............................................................................................................................112
19.2. VD signal connection.........................................................................................................................113
19.3. VD signal connection at each bpp mode.........................................................................................114
20. CAMERA INTERFACE......................................................................................................................116
20.1. Signal Description..............................................................................................................................116
20.2. Camera INPUT.....................................................................................................................................117

S5PV210_HARDWARE DESING GUIDE REV 1.0
7
20.3. Restriction...........................................................................................................................................117
21. MIPI DSI & CSI..................................................................................................................................118
21.1. Signal Description..............................................................................................................................118
21.2. Design Guide.......................................................................................................................................119
22. TV ENCODER....................................................................................................................................120
22.1. Signal Description..............................................................................................................................120
23. HDMI..................................................................................................................................................121
23.1. Overview..............................................................................................................................................121
23.2. Signal Description..............................................................................................................................121
23.3. Circuit Diagram Example...................................................................................................................122
23.4. PCB Artwork Guide............................................................................................................................124
24. IIS MULTI AUDIO INTERFACE (V5.1)..............................................................................................126
24.1. Signal Description..............................................................................................................................126
24.2. Audio Port ...........................................................................................................................................126
25. IIS BUS CONTROLLER ....................................................................................................................128
25.1. Signal Description..............................................................................................................................128
25.2. External Clock Source .......................................................................................................................128
25.3. Connection Example..........................................................................................................................129
26. AC97 CONTROLLER........................................................................................................................130
26.1. AC97 Signal Description....................................................................................................................130
26.2. Audio Ports .........................................................................................................................................130
26.3. Connection Example..........................................................................................................................130
27. PCM BUS CONTROLLER.................................................................................................................131
27.1. Signal Description..............................................................................................................................131
27.2. External Clock Source .......................................................................................................................132
27.3. Connection Example..........................................................................................................................132
28. SPDIF ................................................................................................................................................134
28.1. Signal Description..............................................................................................................................134
29. ADC&TOUCH SCREEN INTERFACE...............................................................................................135
30. KEYPAD INTERFACE.......................................................................................................................136

S5PV210_HARDWARE DESING GUIDE REV 1.0
8
1. Overview
1.1. S5PV210 Pin Information
Definitions
Available Usage(AU)
- G/E/W : GPIO & EINT & Wake up source
- G/E : GPIO & EINT
- G : GPIO
- D : Dedicated signal
- I : Internally connected to MCP and ball out
- I(x) : Internally connected to MCP and No ball out
RET @ Power down
- No_Ret: this signal doesn’t have a retention function in power down mode
- Ret_IO : this signal has a retention function in power down mode and released by setting Enable_GPIO bit
(others[31])
- Ret_IO (sleep) : this signal has a retention function in only sleep mode and released by setting Enable_GPIO bit
(others[31])
- Ret_CF : this signal has a retention function in power down mode and released by setting Enable_CF_IO bit
(others[30])
- Ret_MMC : this signal has a retention function in power down mode and released by setting Enable_ MMC_IO
bit (others[29])
- Ret_UART : this signal has a retention function in power down mode and released by setting
Enable_GPIO_UART_IO bit (others[28]) => Only Uart2, 3
- Ret_Auto : this signal has a retention in power down mode and released automatically after wakeup.
note) Need to more attention when this kinds of signals are used for GPIO,.
Because these signals move to default signal level after wakeup until S/W set to the level.

S5PV210_HARDWARE DESING GUIDE REV 1.0
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XuRXD[0] GPA0[0] GPI PD I(L) UART_0_RXD G/E Ret_IO NC
XuTXD[0] GPA0[1] GPI PD I(L) UART_0_TXD G/E Ret_IO NC
XuCTSn[0] GPA0[2] GPI PD I(L) UART_0_CTSn G/E Ret_IO NC
XuRTSn[0] GPA0[3] GPI PD I(L) UART_0_RTSn G/E Ret_IO NC
XuRXD[1] GPA0[4] GPI PD I(L) UART_1_RXD G/E Ret_IO NC
XuTXD[1] GPA0[5] GPI PD I(L) UART_1_TXD G/E Ret_IO NC
XuCTSn[1] GPA0[6] GPI PD I(L) UART_1_CTSn G/E Ret_IO NC
VDD_EXT0
XuRTSn[1] GPA0[7] GPI PD I(L) UART_1_RTSn G/E Ret_IO NC
VDD_EXT1 XuRXD[2] GPA1[0] GPI PD I(L) UART_2_RXD UART_AUDIO_
RXD G/E Ret_UA
RT NC for RP(Low Power
Audio)debugging

S5PV210_HARDWARE DESING GUIDE REV 1.0
10
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XuTXD[2] GPA1[1] GPI PD I(L) UART_2_TXD UART_AUDIO_
TXD G/E Ret_UA
RT NC for RP(Low Power
Audio)debugging
XuRXD[3] GPA1[2] GPI PD I(L) UART_3_RXD UART_2_CTSn G/E Ret_UA
RT NC
XuTXD[3] GPA1[3] GPI PD I(L) UART_3_TXD UART_2_RTSn G/E Ret_UA
RT NC
XspiCLK[0
] GPB[0] GPI PD I(L) SPI_0_CLK G/E Ret_IO NC
XspiCSn[0
] GPB[1] GPI PD I(L) SPI_0_nSS G/E Ret_IO NC
XspiMISO[
0] GPB[2] GPI PD I(L) SPI_0_MISO G/E Ret_IO NC
VDD_EXT0
XspiMOSI[
0] GPB[3] GPI PD I(L) SPI_0_MOSI G/E Ret_IO NC
VDD_EXT2 XspiCLK[1
] GPB[4] GPI PD I(L) SPI_1_CLK G/E Ret_IO NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
11
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XspiCSn[1
] GPB[5] GPI PD I(L) SPI_1_nSS G/E Ret_IO NC
XspiMISO[
1] GPB[6] GPI PD I(L) SPI_1_MISO G/E Ret_IO NC
XspiMOSI[
1] GPB[7] GPI PD I(L) SPI_1_MOSI G/E Ret_IO NC
Xi2s1SCLK GPC0[0] GPI PD I(L) I2S_1_SCLK PCM_1_SCLK AC97BITCLK G/E Ret_IO NC
Xi2s1CDCL
K GPC0[1] GPI PD I(L) I2S_1_CDCLK PCM_1_EXTCLK AC97RESETn G/E Ret_IO NC
Xi2s1LRCK GPC0[2] GPI PD I(L) I2S_1_LRCK PCM_1_FSYNC AC97SYNC G/E Ret_IO NC
Xi2s1SDI GPC0[3] GPI PD I(L) I2S_1_SDI PCM_1_SIN AC97SDI G/E Ret_IO NC
Xi2s1SDO GPC0[4] GPI PD I(L) I2S_1_SDO PCM_1_SOUT AC97SDO G/E Ret_IO NC
Xpcm2SCLK GPC1[0] GPI PD I(L) PCM_2_SCLK SPDIF_0_OUT I2S_2_SCLK G/E Ret_IO NC
VDD_AUD
Xpcm2EXTC
LK GPC1[1] GPI PD I(L) PCM_2_EXTCL K SPDIF_EXTCLK I2S_2_CDCLK G/E Ret_IO NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
12
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
Xpcm2FSYN
C GPC1[2] GPI PD I(L) PCM_2_FSYNC LCD_FRM I2S_2_LRCK G/E Ret_IO NC
Xpcm2SIN GPC1[3] GPI PD I(L) PCM_2_SIN I2S_2_SDI G/E Ret_IO NC
Xpcm2SOUT GPC1[4] GPI PD I(L) PCM_2_SOUT I2S_2_SDO G/E Ret_IO NC
XpwmTOUT[
0] GPD0[0] GPI PD I(L) TOUT_0 G/E Ret_IO NC
XpwmTOUT[
1] GPD0[1] GPI PD I(L) TOUT_1 G/E Ret_IO NC
XpwmTOUT[
2] GPD0[2] GPI PD I(L) TOUT_2 G/E Ret_IO NC
XpwmTOUT[
3] GPD0[3] GPI PD I(L) TOUT_3 PWM_MIE/PWM_M
DNIE G/E Ret_IO NC MIE PWM control
Xi2c0SDA GPD1[0] GPI PD I(L) I2C0_SDA G/E Ret_IO NC
VDD_EXT0
Xi2c0SCL GPD1[1] GPI PD I(L) I2C0_SCL G/E Ret_IO NC
VDD_EXT1 Xi2c1SDA GPD1[2] GPI PD I(L) I2C1_SDA G/E Ret_IO NC For HDMI

S5PV210_HARDWARE DESING GUIDE REV 1.0
13
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
Xi2c1SCL GPD1[3] GPI PD I(L) I2C1_SCL G/E Ret_IO NC For HDMI
Xi2c2SDA GPD1[4] GPI PD I(L) I2C2_SDA IEM_SCLK G/E Ret_IO NC
Xi2c2SCL GPD1[5] GPI PD I(L) I2C2_SCL IEM_SPWI G/E Ret_IO NC
XciPCLK GPE0[0] GPI PD I(L) CAM_A_PCLK G/E Ret_IO NC
XciVSYNC GPE0[1] GPI PD I(L) CAM_A_VSYNC G/E Ret_IO NC
XciHREF GPE0[2] GPI PD I(L) CAM_A_HREF G/E Ret_IO NC
XciDATA[0
] GPE0[3] GPI PD I(L) CAM_A_DATA[
0] G/E Ret_IO NC
XciDATA[1
] GPE0[4] GPI PD I(L) CAM_A_DATA[
1] G/E Ret_IO NC
XciDATA[2
] GPE0[5] GPI PD I(L) CAM_A_DATA[
2] G/E Ret_IO NC
VDD_CAM
XciDATA[3
] GPE0[6] GPI PD I(L) CAM_A_DATA[
3] G/E Ret_IO NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
14
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XciDATA[4
] GPE0[7] GPI PD I(L) CAM_A_DATA[
4] G/E Ret_IO NC
XciDATA[5
] GPE1[0] GPI PD I(L) CAM_A_DATA[
5] G/E Ret_IO NC
XciDATA[6
] GPE1[1] GPI PD I(L) CAM_A_DATA[
6] G/E Ret_IO NC
XciDATA[7
] GPE1[2] GPI PD I(L) CAM_A_DATA[
7] G/E Ret_IO NC
XciCLKenb GPE1[3] GPI PD I(L)
CAM_A_CLKOU
T G/E Ret_IO NC
XciFIELD GPE1[4] GPI PD I(L) CAM_A_FIELD G/E Ret_IO NC
XvHSYNC GPF0[0] GPI PD I(L) LCD_HSYNC SYS_CS0 VEN_HSYNC G/E Ret_IO NC
XvVSYNC GPF0[1] GPI PD I(L) LCD_VSYNC SYS_CS1 VEN_VSYNC G/E Ret_IO NC
XvVDEN GPF0[2] GPI PD I(L) LCD_VDEN SYS_RS VEN_HREF G/E Ret_IO NC
VDD_LCD
XvVCLK GPF0[3] GPI PD I(L) LCD_VCLK SYS_WE V601_CLK G/E Ret_IO NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
15
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XvVD[0] GPF0[4] GPI PD I(L) LCD_VD[0] SYS_VD[0] VEN_DATA[0] G/E Ret_IO NC
XvVD[1] GPF0[5] GPI PD I(L) LCD_VD[1] SYS_VD[1] VEN_DATA[1] G/E Ret_IO NC
XvVD[2] GPF0[6] GPI PD I(L) LCD_VD[2] SYS_VD[2] VEN_DATA[2] G/E Ret_IO NC
XvVD[3] GPF0[7] GPI PD I(L) LCD_VD[3] SYS_VD[3] VEN_DATA[3] G/E Ret_IO NC
XvVD[4] GPF1[0] GPI PD I(L) LCD_VD[4] SYS_VD[4] VEN_DATA[4] G/E Ret_IO NC
XvVD[5] GPF1[1] GPI PD I(L) LCD_VD[5] SYS_VD[5] VEN_DATA[5] G/E Ret_IO NC
XvVD[6] GPF1[2] GPI PD I(L) LCD_VD[6] SYS_VD[6] VEN_DATA[6] G/E Ret_IO NC
XvVD[7] GPF1[3] GPI PD I(L) LCD_VD[7] SYS_VD[7] VEN_DATA[7] G/E Ret_IO NC
XvVD[8] GPF1[4] GPI PD I(L) LCD_VD[8] SYS_VD[8] V656_DATA[0
] G/E Ret_IO NC
XvVD[9] GPF1[5] GPI PD I(L) LCD_VD[9] SYS_VD[9] V656_DATA[1
] G/E Ret_IO NC
XvVD[10] GPF1[6] GPI PD I(L) LCD_VD[10] SYS_VD[10] V656_DATA[2
] G/E Ret_IO NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
16
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XvVD[11] GPF1[7] GPI PD I(L) LCD_VD[11] SYS_VD[11] V656_DATA[3
] G/E Ret_IO NC
XvVD[12] GPF2[0] GPI PD I(L) LCD_VD[12] SYS_VD[12] V656_DATA[4
] G/E Ret_IO NC
XvVD[13] GPF2[1] GPI PD I(L) LCD_VD[13] SYS_VD[13] V656_DATA[5
] G/E Ret_IO NC
XvVD[14] GPF2[2] GPI PD I(L) LCD_VD[14] SYS_VD[14] V656_DATA[6
] G/E Ret_IO NC
XvVD[15] GPF2[3] GPI PD I(L) LCD_VD[15] SYS_VD[15] V656_DATA[7
] G/E Ret_IO NC
XvVD[16] GPF2[4] GPI PD I(L) LCD_VD[16] SYS_VD[16] G/E Ret_IO NC
XvVD[17] GPF2[5] GPI PD I(L) LCD_VD[17] SYS_VD[17] G/E Ret_IO NC
XvVD[18] GPF2[6] GPI PD I(L) LCD_VD[18] SYS_VD[18] G/E Ret_IO NC
XvVD[19] GPF2[7] GPI PD I(L) LCD_VD[19] SYS_VD[19] G/E Ret_IO NC
XvVD[20] GPF3[0] GPI PD I(L) LCD_VD[20] SYS_VD[20] G/E Ret_IO NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
17
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
XvVD[21] GPF3[1] GPI PD I(L) LCD_VD[21] SYS_VD[21] G/E Ret_IO NC
XvVD[22] GPF3[2] GPI PD I(L) LCD_VD[22] SYS_VD[22] G/E Ret_IO NC
XvVD[23] GPF3[3] GPI PD I(L) LCD_VD[23] SYS_VD[23] V656_CLK G/E Ret_IO NC
XvVSYNC_L
DI GPF3[4] GPI PD I(L) VSYNC_LDI VSYNC_LDI VSYNC_LDI G/E Ret_IO NC
XvSYS_OE GPF3[5] GPI PD I(L) SYS_OE SYS_OE VEN_FIELD G/E Ret_IO NC
Xmmc0CLK GPG0[0] GPI PD I(L) SD_0_CLK G/E Ret_MM
C NC
Xmmc0CMD GPG0[1] GPI PD I(L) SD_0_CMD G/E Ret_MM
C NC
Xmmc0CDn GPG0[2] GPI PD I(L) SD_0_CDn G/E Ret_MM
C NC
Xmmc0DATA
[0] GPG0[3] GPI PD I(L) SD_0_DATA[0
]
VDD_EXT0
Xmmc0DATA
[1] GPG0[4] GPI PD I(L) SD_0_DATA[1
] G/E Ret_MM
C NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
18
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
Xmmc0DATA
[2] GPG0[5] GPI PD I(L) SD_0_DATA[2
] G/E Ret_MM
C NC
Xmmc0DATA
[3] GPG0[6] GPI PD I(L) SD_0_DATA[3
] G/E Ret_MM
C NC
Xmmc1CLK GPG1[0] GPI PD I(L) SD_1_CLK G/E Ret_MM
C NC
Xmmc1CMD GPG1[1] GPI PD I(L) SD_1_CMD G/E Ret_MM
C NC
Xmmc1CDn GPG1[2] GPI PD I(L) SD_1_CDn G/E Ret_MM
C NC
Xmmc1DATA
[0] GPG1[3] GPI PD I(L) SD_1_DATA[0
] SD_0_DATA[4] G/E Ret_MM
C NC
Xmmc1DATA
[1] GPG1[4] GPI PD I(L) SD_1_DATA[1
] SD_0_DATA[5] G/E Ret_MM
C NC
Xmmc1DATA
[2] GPG1[5] GPI PD I(L) SD_1_DATA[2
] SD_0_DATA[6] G/E Ret_MM
C NC
Xmmc1DATA GPG1[6] GPI PD I(L) SD_1_DATA[3 SD_0_DATA[7] G/E Ret_MM NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
19
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
[3] ] C
Xmmc2CLK GPG2[0] GPI PD I(L) SD_2_CLK G/E Ret_MM
C NC
Xmmc2CMD GPG2[1] GPI PD I(L) SD_2_CMD G/E Ret_MM
C NC
Xmmc2CDn GPG2[2] GPI PD I(L) SD_2_CDn G/E Ret_MM
C NC
Xmmc2DATA
[0] GPG2[3] GPI PD I(L) SD_2_DATA[0 ] G/E Ret_MM
C NC
Xmmc2DATA
[1] GPG2[4] GPI PD I(L) SD_2_DATA[1 ] G/E Ret_MM
C NC
Xmmc2DATA
[2] GPG2[5] GPI PD I(L) SD_2_DATA[2 ] G/E Ret_MM
C NC
VDD_EXT1
Xmmc2DATA
[3] GPG2[6] GPI PD I(L) SD_2_DATA[3 ] G/E Ret_MM
C NC
VDD_EXT2 Xmmc3CLK GPG3[0] GPI PD I(L) SD_3_CLK G/E Ret_MM
C NC

S5PV210_HARDWARE DESING GUIDE REV 1.0
20
GPIO
Reset
value
IO Power
Domain Ball Name Port
In/
Out Pu/ Pd
Rese
t
stat
us
Func-0 Func-1 Func-2 Func-3 AU RET @
Power
down
Not
Use
d Circuit guide
Xmmc3CMD GPG3[1] GPI PD I(L) SD_3_CMD G/E Ret_MM
C NC
Xmmc3CDn GPG3[2] GPI PD I(L) SD_3_CDn G/E Ret_MM
C NC
Xmmc3DATA
[0] GPG3[3] GPI PD I(L) SD_3_DATA[0
] SD_2_DATA[4] G/E Ret_MM
C NC
Xmmc3DATA
[1] GPG3[4] GPI PD I(L) SD_3_DATA[1
] SD_2_DATA[5] G/E Ret_MM
C NC
Xmmc3DATA
[2] GPG3[5] GPI PD I(L) SD_3_DATA[2
] SD_2_DATA[6] G/E Ret_MM
C NC
Xmmc3DATA
[3] GPG3[6] GPI PD I(L) SD_3_DATA[3
] SD_2_DATA[7] G/E Ret_MM
C NC
XEINT[0] GPH0[0] GPI PD I(L) G/E/
W No_Ret NC
Can be used as a
PS_HOLD pin
Wakeup source
VDD_SYS0
XEINT[1] GPH0[1] GPI PD I(L) G/E/ No_Ret NC wakeup source