Samsung MR-AH01C User manual

Wireless Remote Controller
MR-AH01C
MR-AC01C
OWNER’S
INSTRUCTIONS
System Air Conditioner
E C DB98-05155A(2)

Safety Precautions
◆Do not attempt to install or repair this wireless remote
controller by yourself.
◆This remote controller contains no user-serviceable
parts. Always consult authorized service personnel
for repairs.
◆When moving, consult authorized service personnel
for disconnection and installation of the remote
controller.
◆Ensure that the wall is strong enough to support the
weight of the remote controller and the remote
control holder.
◆In the event of a malfunction (burning smell, etc.),
immediately stop operation, turn off the electrical
breaker, and consult authorized service personnel.
WARNING
CAUTION ◆
Do not use inflammable gases near the remote
controller.
◆ Do not spill water into the wireless remote controller.
◆ Do not operate the remote controller with wet hands.
◆ Do not install the remote controller in a location
where it will come into contact with the combustible
gases, machine oil, sulphide gas, etc.
◆ Do not press buttons with a pointed thing.
◆ Do not use this wireless remote controller for other
purpose.
◆ Do not spray an insecticide or other combustible
things on the wireless remote controller.
◆ Do not clean the wireless remote controller with
benzene, solvents or other chemicals.
◆ Do not give a shock to the wireless remote controller
or disassemble it by yourself.
E-2
●
Before using the wireless remote controller, read carefully this instructions.
●
After reading the instructions, keep this owner's instructions and the
installation manual in a handy and safe place. If a user is changed, you must
hand over the manuals.
●
Never attempt to install the air conditioning system or to move the remote
control holder by yourself.

E-3
Contents
◆ V IEW OF THE W IRELESS R EMOTE C ONTROLLER
◆ G ETTING S TART
◆ I NSERTING THE W IRELESS
R EMOTE C ONTROLLER
B ATTERIES
◆ S ELECTING THE A UTOMATIC O PERATING M ODE
◆ C OOLING Y OUR R OOM
◆ H EATING Y OUR R OOM
(E XCEPT COOLING ONLY MODELS )
◆ R EMOVING
E XCESS H UMIDITY
◆ A IRING Y OUR R OOM
◆ A DJUSTING THE
A IR F LOW D IRECTION
(E XCEPT DUCT TYPE )
◆ S ETTING THE O N T IMER
◆ S ETTING THE O FF T IMER
4
6
7
8
10
12
14
16
17
18
20

E-4
View of the Wireless Remote Controller
◆ After cleaning the air filter, press the Filter Reset button.
◆Duct type air conditioner does not have function of adjusting air flow direction.
Therefore, the function is not operated even if you press the swing button.
NN
NNoo oott ttee ee
Operating mode Mode selection button
Filter Reset button
Swing button
(Except Duct type)
On Timer button
Off Timer button
On/Off & Timer
Set/Cancel button
Fan speed adjustment
button
Temperature adjustment
buttons
Temperature setting
Fan speed
Air flow direction
On Timer setting
Off Timer setting
Battery discharge indicator
Heat Pump Models (MR-AH01C)

E-5
◆ After cleaning the air filter, press the Filter Reset button.
◆Duct type air conditioner does not have function of adjusting air flow direction.
Therefore, the function is not operated even if you press the swing button.
NN
NNoo oott ttee ee
Operating mode Mode selection button
Filter Reset button
Swing button
(Except Duct type)
On Timer button
Off Timer button
On/Off & Timer
Set/Cancel button
Fan speed adjustment button
Temperature adjustment buttons
Temperature setting
Fan speed
Air flow direction
On Timer setting
Off Timer setting
Battery discharge indicator
Cooling Only Models (MR-AC01C)

E-6
G etting Start
You have just purchased a wireless remote controller and
it has been installed by your installation specialist.
Your Owner’s Instructions contain much valuable information
on using your wireless remote controller. Please take the time to
read them as they will help you take full advantage of the unit’s
features.
In the main part of the document, you will find a series of step-by-step
procedures for each function available.
The illustrations in the step-by-step procedures use three different
symbols:
PRESS PUSH HOLD DOWN

Inserting the Wireless Remote Controller Batteries
E-7
Push the battery cover on the rear of the remote
controller with your thumb in the direction of the arrow
and remove it.
1
You must insert or replace the remote controller
batteries when :
◆You purchase the air conditioner
◆The remote controller does not work
correctly
Insert the two batteries, taking care to respect the
polarities :
◆+ on the battery with + on the remote controller.
◆- on the battery with - on the remote controller.
2
Close the cover by sliding it back until it clicks into place.
3
◆Use two AAA, LR03 1.5V batteries.
◆Do not use old batteries or different kinds of
batteries together.
◆Batteries may be completely discharged after 12
months, even if they have not actually been used.
NN
NNoo oott ttee ee

E-8
Selecting the Automatic Operating Mode
In the Automatic mode, the room temperature and the
fan speed are controlled automatically.
If necessary, press (ON/OFF) button.
Result: ◆The On/Off indicator on the indoor unit or
receiver & display unit comes on.
◆The air conditioner runs in the mode
selected when the unit was last used.
◆The indoor unit or receiver & display unit
beeps.
1
To select the AUTO mode, press the Mode button until
is displayed at the top of the wireless remote controller.
Result: ◆The indoor or receiver & display unit unit
beeps.
◆The air conditioner runs in AUTO mode.
2
The air conditioner is fitted with a
protection mechanism to prevent the unit
from being damaged when it is started
immediately after being:
◆Plugged in
◆Stopped
lt will start up normally after three minutes.
IMPORTANT
◆You can change modes at any time.
NN
NNoo oott ttee ee

E-9
To adjust the temperature, press the Temperature
buttons one or more times until the required temperature
is displayed. Possible temperatures are between 18°C
and 30°C inclusive.
Result: ◆Each time you press Temperature buttons:
- The temperature is adjusted by 1°C.
◆
The air conditioner start cooling, provided
that the room temperature is than the
selected temperature.
- The quantity of air is adjusted automatically.
3

E-10
Cooling Your Room
If necessary, press (ON/OFF) button.
Result: ◆The On/Off indicator on the indoor unit or
receiver & display unit comes on.
◆The air conditioner runs in the mode
selected when the unit was last used.
◆The indoor unit or receiver & display unit
beeps.
1
You must select the COOL mode if you wish to adjust the :
◆Cooling temperature
◆Fan speed when cooling
To select the COOL mode, press the Mode button until
is displayed at the top of the wireless remote controller.
Result: ◆The indoor unit or receiver & display unit
beeps.
◆The air conditioner runs in COOL mode.
2
The air conditioner is fitted with a
protection mechanism to prevent the unit
from being damaged when it is started
immediately after being:
◆Plugged in
◆Stopped
lt will start up normally after three minutes.
IMPORTANT
◆You can change modes at any time.
NN
NNoo oott ttee ee