Samsung ADT Security Hub User manual

ADT Security Hub
User Guide

This User Guide provides an introduction to the key features
of the ADT Security Hub. Visit SmartThings.com/Support-ADT
for more detailed information and customer support.
Contents
Intrusion Detection
• Introduction
• Arming the system
• Arming the system and bypassing detectors
• Disarming the system
• In the event of an intrusion
• In the event of a false alarm
• Advanced intrusion detection
• Home button
• Emergency button
• Manually notifying ADT
• System icons
• Local Walk Test
ADT Security Hub
A
B
Life Safety
• Introduction
• In the event of smoke or extreme temperatures
• In the event of carbon monoxide
• In the event of a water leak
C
Security Codes
• Master user code
• User codes
D
System Settings
E
Transferring Your ADT Security Hub
F

AADT Security Hub
Home button
• No lights: The system is not ready to be armed. One or
more protected doors or windows are open.
• Green: The system is ready to be armed. All protected
doors and windows are closed.
• Flashing green: The system is ready to be armed. All
protected doors and windows are closed but there is a
power outage.
• Flashing orange: The system is not ready to be armed. One
or more protected doors or windows are open, and there is
a power outage.
ADT Security Hub
Use the Home button to wake your ADT Security Hub from sleep
mode or to return to the Home screen. The Home button will
change color to show the status of your system:
• Red: The system is armed.
• Flashing red: The system is armed and an alarm has been
triggered.
Emergency Button
Home Screen
Home Button

Press the Emergency button to manually notify ADT of a panic,
re, or emergency event.
The touchscreen will display buttons for Panic, Fire, and Emergency.
Requires an optional ADT professional monitoring service.
Visit SmartThings.com/ADT for more information.
ADT Security Hub
Manually notifying ADT
ADT Security Hub
Use the Emergency button to manually notify ADT of a panic,
re, or emergency event.
The Emergency button changes color to show the status of
your system:
• No lights: The emergency button is not available.
• White: The emergency button is ready for use.
• Blinking white: An emergency alarm is in progress.
Emergency button
Requires an optional ADT professional monitoring service.
Visit SmartThings.com/ADT for more information.
Press and hold one of the Panic, Fire, or Emergency buttons for two
seconds. Your ADT Security Hub will notify ADT and an operator will
respond according to the terms of your monitoring service.
For compliance with ANSI/SIA CP-01-2010 and to help reduce the risk of
false alarms, you must press the Emergency button on the ADT Security
Hub, and then press and hold one of the Panic, Fire, or Emergency icons
for two seconds.

The following icons may appear at the top of the touchscreen:
System icons
ADT Security Hub ADT Security Hub
Power Connected
Power Not Connected
Low Backup Battery
System Sounds On
System Sounds Off
(Siren still active)
Dim Touchscreen
(Touch to dim screen)
Incoming Messages
(Touch to see messages)
4
Panic, Fire, and Emergency buttons on your ADT Security Hub:

BIntrusion Detection
Intrusion detection is provided by devices such as the ADT Door
and Window Detector or the ADT Motion Detector. These devices
are only active when armed by your ADT Security Hub.
If your home is protected by an ADT professional monitoring
service, the ADT Security Hub will activate the alarm siren and
notify ADT as soon as an intrusion is detected and initiate an
emergency response.
If your home is not protected by an ADT professional monitoring
service, the ADT Security Hub will activate the alarm siren as soon
as an intrusion is detected but will not notify ADT.
Visit SmartThings.com/ADT for more details on ADT professional
monitoring services and to see the full list of compatible detectors
and alarms.
Introduction
It is strongly recommended that you perform a weekly test of your
ADT Security Hub, detectors, and alarms:
Local walk test
Select System Settings from the Home screen.
Enter the Master User Code.
Select Walk Test.
Select Sensors Test and follow the on-screen instructions.
Select Console Test and follow the on-screen instructions.
1.
2.
3.
4.
5.
Tap or the Home button to exit Test Mode.6.
ADT Security Hub
• If a detector fails the Sensors Test, check that it’s
been installed correctly or visit SmartThings.com/
Support-ADT for assistance.

Press the Arm Stay button to arm the system when people or
large pets will remain in the house. This will arm all ADT Door and
Window Detectors but will not arm any ADT Motion Detectors. The
alarm will be activated if a protected door or window is opened.
Arming the system
Intrusion Detection
Press the Arm Away button to arm the system when everyone
leaves the house. This will arm all ADT Door and Window Detectors,
and all ADT Motion Detectors. The alarm will be activated if a
protected door or window is opened, or if motion is detected.
Pressing the Arm Away button will start a 60-second exit delay
countdown. This will give you enough time to leave the house
before the system is armed.
Intrusion Detection
Arm AwayArm Stay

If you try to arm the system while protected doors or windows are
still open, the ADT Security Hub will display a list of sensors that
are not ready to be armed.
Arming the system and bypassing detectors
You can press the Silence button to silence the countdown, or you
can press the Disarm button to cancel the countdown and leave
the system unarmed.
Intrusion DetectionIntrusion Detection
Disarm ButtonSilence Button

You can close the open doors or windows to remove the
warnings, or you can bypass these sensors by pressing the
Bypass All button and entering your user code.
Bypassed sensors do not protect doors or windows, and will
not activate the alarm siren, notify ADT, or send an alert to your
smartphone in the event of an intrusion. Bypassed sensors revert
to normal operation when the alarm system is next armed.
If the system is armed in Away Mode, it must be disarmed within
30 seconds of entering the house through a protected door or area.
Disarming the system
Press the Disarm button and enteryour user code to disarm the
system.
If the system is armed in Stay mode, it must be disarmed before
leaving the house through a protected door.
Intrusion DetectionIntrusion Detection
Disarm Button

You can also press the Quick Exit button to temporarily disarm
protected doors and start a 60-second exit delay countdown. This
will give you enough time to leave the house before the system is
re-armed.
Intrusion Detection
In the event of an intrusion
Areas protected by an ADT Motion Detector
The alarm siren will be activated immediately and continue
sounding for 4 minutes, or until a correct user code is entered
on the ADT Security Hub to disarm the system.
Doors and windows protected by an ADT Door and Window
Detector
The alarm siren will be activated immediately and continue
sounding for 4 minutes, or until a correct user code is entered
on the ADT Security Hub to disarm the system.
Intrusion Detection
Entry/exit doors protected by an ADT Door and Window Detector
The system will start a 30-second entry delay countdown,
giving you enough time to disarm the system by entering a
correct user code on the ADT Security Hub. If the system is not
disarmed in time, the alarm siren will be activated for 4 minutes
or until a correct user code is entered.
Quick Exit Button

Homes protected by an optional ADT Professional
Monitoring Service
Your ADT Security Hub will notify ADT as soon as the alarm siren
is activated and an operator will respond according to the terms
of your monitoring service.
Visit SmartThings.com/ADT for more information about ADT professional
monitoring services.
In the event of a false alarm
If the system is not disarmed in time, the alarm siren will be
activated and ADT will contact you to conrm that it is a false
alarm.
Advanced intrusion detection
If an ADT detector activates the alarm siren more than once
during a single arming session, that detector will be bypassed
for the next 8 hours or until the system is manually re-armed.
Intrusion Detection Intrusion Detection
Bypassed sensors do not protect doors or windows, and will not activate
the alarm siren, notify ADT, or send an alert to your smartphone in the
event of an intrusion.
This helps to reduce false alarms caused by doors or windows
repeatedly swinging open and closed.

CLife Safety Protection
Introduction
Life safety protection is provided by devices such as the ADT Smoke
Alarm, the ADT Carbon Monoxide Alarm and the ADT Water Leak
Detector. These devices are always active and monitored by your
ADT Security Hub.
If your home is protected by an ADT professional monitoring
service, the ADT Security Hub will activate the alarm siren and
notify ADT as soon as smoke or carbon monoxide is detected.
If your home is not protected by an ADT professional monitoring
service, the ADT Security Hub will activate the alarm siren as soon
as smoke or carbon monoxide is detected but will not notify ADT.
ADT Smoke Alarms and ADT Carbon Monoxide Alarms must be installed in
compliance with all national, regional, and local laws, statutes, and
guidelines.
Visit SmartThings.com/ADT for more details on ADT professional monitoring
services and to see the full list of compatible detectors and alarms.
In the event of smoke or extreme temperatures
If an ADT Smoke Alarm detects smoke or extreme temperatures:
If your home is protected by an ADT professional monitoring
service, the ADT Security Hub will notify ADT as soon as the alarm
siren is activated and an operator will respond according to the
terms of your service.
If a re alarm is activated, the system emits a warning siren and
immediately reports a re to ADT.
• The alarm siren on the ADT Smoke Alarm will be activated.
• The alarm siren on the ADT Security Hub will be activated
for 4 minutes or until a correct user code is entered to
cancel the alarm.
Life Safety Protection

Note: It is important to establish and practice an escape plan
with all members of your household in the event of a re.
Read the user guide that came with your ADT Smoke Alarm
to learn more about re safety, alarm testing, and creating an
escape plan.
• If ames or smoke are present, yell "Fire!" to alert all
occupants of a re.
• Immediately evacuate all occupants from the premises
and remain at a safe distance away from the premises.
• DANGER: To protect yourself and others from serious injury
and/or death, do NOT re-enter the premises until it has been
deemed safe by emergency ofcials.
• Dial 911 to report the situation to authorities. Always wait
to call from a safe location.
To protect yourself and occupants do the following:
Life Safety Protection Life Safety Protection
If an ADT Carbon Monoxide Alarm detects critical levels of carbon
monoxide for more than 2 minutes:
If your home is protected by an ADT professional monitoring
service, the ADT Security Hub will notify ADT as soon as the alarm
siren is activated and an operator will respond according to the
terms of your service.
• The alarm siren on the ADT Carbon Monoxide Alarm will be
activated.
• The alarm siren on the ADT Security Hub will be activated
for 4 minutes or until a correct user code is entered to cancel
the alarm.
In the event of carbon monoxide

Read the user guide that came with your ADT Carbon Monoxide
Alarm to learn more about how the alarm responds to low or
moderate levels of carbon monoxide.
In the event of a water leak
If an ADT Water Leak Detector detects water, it will send a message
to the ADT Security Hub.
If your home is protected by an ADT professional monitoring
service, the ADT Security Hub will notify ADT and an operator will
respond according to the terms of your service.
Note: Unlike the other ADT detectors and alarms, the ADT Water Leak
Detector is unable to communicate with the ADT Security Hub during
a power or internet outage.
In the event of a critical carbon monoxide alert, you should
immediately open a window or door to get fresh air. Evacuate all
occupants from the premises and call 911 or the re department.
Remain at a safe distance and do not re-enter the premises until it
has been deemed safe by emergency ofcials.
Life Safety Protection
The ADT Security Hub uses different types of security codes:
Introduction
DSecurity Codes
• Master user code
• User codes
To change the Master User Code:
You are provided with a single Master User Code for accessing
System Settings. The Master User Code is set by default to 1111
but should be changed after setup.
Master user code
1.
2.
Select System Settings from the Home screen.
Enter the Master User Code.

4.
5.
6.
7.
Tap next to Master User.
Tap next to Code.
Enter a new Master User Code and then select Next.
Enter the new Master User Code again as conrmation and
then select Done.
Security Codes Security Codes
The Master User Code must be unique and cannot be the same as
any of the User Codes.
You can create up to 98 unique User Codes, allowing different
people to arm and disarm the system.
User codes
To create a new User Code:
8. Press the Home button to return to the Home Screen.
1. Select System Settings from the Home screen.
2. Enter the Master User Code.
3.
4.
5.
6.
7.
Select Users and then Add User.
Enter a name for the new user and then select Next.
Enter a unique code for the new user and then select Next.
Enter the unique code again as conrmation and then
select Done.
Press the Home button to return to the Home Screen.
All User Codes must be unique and cannot be the same as the
Master User Code.
3. Select Users.

By default, each User Code is valid at any time of the day and on
any day of the week. To create a specic schedule for when you
want a User Code to be valid:
1. Select System Settings from the Home screen.
2. Enter the Master User Code.
Security Codes
3. Select Users.
Scroll down and tap next to Add Schedule.
Select the type of schedule: Recurring, Date, or Date Range.
Select the days of the week and times of the day when you
want the User Code to be valid.
4.
5.
6.
7.
Tap next to a user.
Tap the icon to conrm the schedule when complete.8.
9. Press the Home button to return to the Home Screen.
ESystem Settings
The following settings are accessible from the System Settings
menu.
Use this setting to adjust the volume for:
Note: Volume of the ADT Security Hub siren cannot be changed.
• Keypad tones
• Voice and chime responses
• System responses
Sounds
Use this setting to:
Screens
• Adjust the screen brightness

Use this setting to run diagnostic tests on the:
• ADT Security Hub
• Detectors
• Alarms
System Tests
Use this setting if the LTE cellular data backup module needs
replacing.
Cell Radio Swap
System Settings F Transferring YourADT Security Hub
If you want to transfer your ADT Security Hub to another person,
visit SmartThings.com/Support-ADT to learn more about erasing
settings, cancelling professional monitoring services, and to see
guidelines for the new user.
• Deactivate the touchscreen for 30 seconds so that it can
be cleaned
• Adjust the length of time before the touchscreen goes into
sleep mode

Once you have setup your detectors and alarms, keep the
QR codes here for future reference.
Once you have setup your detectors and alarms, keep the
QR codes here for future reference.
QR Codes QR Codes

SmartThings, Inc., 665 Clyde Ave, Mountain View, CA 94043, USA. Information in this document is subject to
change without notice. Copyright 2017 SmartThings, Inc. All rights reserved. ADT and the ADT logo are marks
and/or registered marks of ADT. Unauthorized use is strictly prohibited. Revised 06/17.
P/N 10016958.