Samsung SDE-3004 User manual

Great user manuals database on UserManuals.info
EZ View Kit
Quick Start Guide
SDE-3004
1. Connecting with Other Devices
2. Installation
3. Starting Up
4. REC & Play
5. Router & Port Forwarding Set Up
6. Web Browsing
7. Monitoring

Great user manuals database on UserManuals.info
English-2
1. CONNECTING WITH OTHER DEVICES
J
`Please make sure not to fully expose the camera to rain. The camera must be installed under a shelter to avoid exposure to excessive rain or
moisture.
`The camera satisfies the IP65 standard, and direct exposure to water or moisture may cause problem such as condensation.
ÚIf you do not use the Internet, just follow the steps below:
1 2 4 5 6 11 12 13 14 15 16 24
Broadband
Router or HUB
Local PC
Broadband Modem
1 2 3 4 G 1 COM G
ALARM IN ALARM OUT
NETWORK
USB
CONSOLE
VGA
AUDIO IN
AUDIO OUT
VIDEO OUT
DC 12V
1 2
3 4

Great user manuals database on UserManuals.info
English-3
2. INSTALLATION
Connect the camera to the Camera In port.
1
Connect the LAN cable and mouse.
The default connection for use of the Internet is as follows:
You can connect a USB HDD mouse to the USB port.
3
Connect the DC adaptor.
4
Connect the Video and Audio Out connectors to the
monitor.
For a PC monitor, use the VGA connector for the
connection.
2
VIDEO OUT Connection
AUDIO OUT Connection
VGA OUT Connection
LAN Mouse
Local PC
Broadband
Modem
Connect the modem to the
WAN port of the router and
connect each of the PC and
the set to the LAN port.
Broadband
Router or HUB
1 2 3 4 G 1 COM G
ALARM IN ALARM OUT
NETWORK
USB
CONSOLE
VGA
AUDIO IN
AUDIO OUT
VIDEO OUT
DC 12V
1 2 3 4 G 1 COM G
ALARMIN ALARM OUT
NETWORK
USB
CONSOLE
VGA
AUDIO IN
AUDIO OUT
VIDEO OUT
DC 12V
TO CAMERA SIDE ONLY
TO DVR SIDE ONLY
Connecting the Camera
M
`There are two labels affixed at the end of the jacks of camera
cable, indicating one of the jacks should be connected to DVR,
and the other should be connected to camera. Please check it
first before connection.

Great user manuals database on UserManuals.info
English-4
3. STARTING Up
Connect the power source.
5Press the [MENU] button on the remote control. 7
Select <Date/Time/Language> in <System> menu.
8
Use the mouse to adjust the time setting.
9
Select the Network menu. Sets the Connection type to
<Static IP> and enter the IP address. Click the <OK>
button.
10
ÚTo apply your setting click the <OK> button.
ÚIf using DI-624 manufactured by D-link
IP ADDRESS:192.168.1.200/
GATEWAY: 192.168.1.1 / SUBNET MASK: 255.255.255.0 /
1ST DNS SERVER: 168.126.63.1 / 2ND DNS SERVER:
168.126.63.2
When prompted, use the virtual keyboard to enter the
password (default: 4321) in the PASSWORD input box.
6
Using the Virtual Keyboard
6-1
ÚIf you don't change the “auto logout” item, please
refer 7. The login prompt in 6only appears when
you change the auto logout time.
ÚAll operations can be controlled with the mouse.
1. Use the direction buttons ($%_+) to move to a desired
character and press the [ENTER] button.
2. Use the < > button to erase the previous character.
3. Use the < > button to toggle the letter case.
4. Complete your input and when done, click <OK> to close the
virtual keyboard.
OK Cancel
`1 2 3 4 5 6 78 9 0 - =

q w e r t y u i o p [ ] \ Del
a s d f g h j k l ; ‘ Caps Lock
z x c v b n m , . / Shift
Space Ctrl
System
Logout Return
Date/Time/Language
Permission Management
System Management
Log Information
Date/Time/Language
Date/Time/Language
Holiday
Date 2012-01-01 YYYY-MM-DD
Time 08:14:24 24 Hours
Time Zone GMT
Time Sync. Setup
DST Dec First (Sun) 0 Dec First (Sun) 0
Language English
OK Cancel
Connection Mode
Connection Protocol
Connection Mode Static IP
Bandwidth 2Mbps
OK Cancel
IP 192.168. 1.200
Gateway 192.168. 1. 1
Subnet Mask 255.255.255. 0
DNS Manual 168.126. 63. 1
2012-01-01 01:10:25
Login
ID admin
Password
OK Cancel

Great user manuals database on UserManuals.info
English-5
4. REC & pLAY
Press the [MENU] button on the remote control.
Select <Record>.
11
To change the record quality & resolution, select
<REC Quality & Resolution>.
If you change the setting of the resolution and the remaining
rate, the remaining count shows each available resolution.
13
Press the [SEARCH] button on the remote control.
14
Set each of the Record Schedule options.
To change the setting, set the channel then select the
time and date you when want to record.
Press the [ENTER] button while the cells are selected.
The record type will cycle through <No Recording>-
<Continuous>-<Event>-<Both(Cont&Evnt)>.
The default is as shown below.
12
Select a desired date in the calendar, and a desired
timeline in the Time bar, and press the <Play> button.
15-1
If you have set the event recording, you can play a
desired scene using the <Event Search> function. Set
a desired date in the calendar and the result will be
listed on the table.
Select one you desired and press the <Play> button.
15-2
The colored line indicates types of the recording data.
If you want to play a time specific data, enter an exact
time.
SYSTEM RECORD SIZE POSSIBLE FPS
NTSC
CIF 352 × 240 OFF, 1~30
2CIF 704 × 240 OFF, 1~30
4CIF 704 × 480 OFF, 1~30
PAL
CIF 352 x 288 OFF, 1~25
2CIF 704 x 288 OFF, 1~25
4CIF 704 x 576 OFF, 1~25
You can change the play speed or channel, or stop the
playback using the onscreen button bar.
16
Record
Logout Return
Recording Schedule
Event Record Duration
REC Quality & Resolution
Record Option
CH Resolution
Record Rate Record Quality 
1 CIF(S) 7fps Level4 
2 CIF(S) 7fps Level4 
3 CIF(S) 7fps Level4 
4 CIF(S) 7fps Level4 
REC Quality & Resolution
Standard Event
OK Cancel
Remaining count : 4CIF(L) : 22CIF(M) : 4CIF(S) : 8
Event Search
CAM 01
2012-01-01
Play Return
Previous/Next Page
2012/01/01 00:01:22
No. Date/Time Preview Event
3 02:47:54 ~ 02:48:59 Motion
2 00:39:06 ~ 00:40:30 Motion
1 00:01:22 ~ 00:02:28 Motion
Go to First Go to Last
Overlapped Data List1
2012-01-01 01:10:25
REC
Time Search
2012-01-01
Play Return
2012/01/01 00:01:17
Standard Schedule
Motion Etc
V.Loss
Go to First Go to Last
Zoom In Zoom Out
All Data
CAM 01
CAM 02
CAM 03
CAM 04
00:01
Overlapped Data List1

Great user manuals database on UserManuals.info
English-6
5. ROUTER & pORT FORWARDING SET Up
The following is configuration for the Internet connection.
This is a typical example.
17
In the Network Properties window, check the IP address
and gateway.
18
If you first connect to the router, you will see the “Setup Wizard” run that proceeds in the following order.
20
Connect to the router using the gateway address found
in step ‘ 18 ’ above.
19
POWER REC
DIGITALVIDEO RECORDER
Cable/ADSL Modem
DDNS Server
(websamsung.net)
Local PC
Direct LAN
(Fixed/Static IP)
or
Broadband
Router or HUB
DVR
Internet
Port Forwarding
When the router setting is done, select Virtual Server in
the “Advanced” tab where you can configure the Port
Forwarding settings. Click “Apply” to apply your
settings.
`For more information, refer to the router guide of the manual CD.
(Model: D-LINK DI-624).
21-1
Running the Quick Connect program
`For more information, refer to the quick connect guide of the
provided manual CD.
21-2
It is easy for you to use DHCP setting for Quick Connection Program.
Path: Network Connection Mode Connection
Change: Static IP Dynamic IP
1. Insert the provided CD into your computer’s CD drive, and
double click “Quick Connect.exe” program to run it.
2. Click [Next >] button.
3. When < > appears on the right side of TCP Port and Web
port number, click [Next >] button.
4. Click [Finish] button to exit the program.
IP : 192.168.1.200
Protocol : TCP
Private Port : 4520~4524
Public Port : 4520~4524
IP : 192.168.1.200
Protocol : TCP
Private Port : 80
Public Port : 80
192.168.1.200
255.255.255.0
192.168.1.1
   

Great user manuals database on UserManuals.info
English-7
6. WEb bROWSING
In the address bar of Internet Explorer, enter the Set IP.
For the internal network, enter the Set Local IP and for the
external network, enter the DDNS address.
* Refer to the domain name of the set defined in DDNS
Menu.
`If you select <iPOLiS>, the “DDNS host address” item will be
displayed. iPOLiS users should register the device with the website
(Domestic (Korea): http://www.samsungipolis.co.kr, Overseas:
http://www.samsungipolis.com) and provide the user name.
(ex: Registered as SDE-300X_HOME)
Connect to the Web Viewer and enter the user ID and
password.
Default ID: admin, PW: 4321
`For more information, refer to the user manual. (Page 66)
`The default password can be exposed to a hacking thread so it is
recommended to change the password after installing the product.
Note that the security and other related issues caused by the
unchanged password shall be responsible for the user.
If the popup window is not activated, unblock the popup.
If you first connect to the PC, you will see
a message as shown.
Install the suggested ActiveX control.
If you first connect to the PC, you will see a message as
shown above. Click “Install” to install the suggested
software.
22
23
Connection Mode
Connection Protocol
Connection Mode Static IP
Bandwidth 2Mbps
OK Cancel
IP 192.168. 1.200
Gateway 192.168. 1. 1
Subnet Mask 255.255.255. 0
DNS Manual 168.126. 63. 1
EX. LAN http://192.168.1.200:80
(when you connect the set within Local
Network or know that IP)
WAN http://www.samsungipolis.com/User ID
(When you connect the set via External Network)
OK Cancel
DDNS
DDNS Site iPOLiS
Host Name www.samsungip...
User Name SDE-3004_HOME
User Password
DDNS Host Address http://www.samsungipolis.com/SDE-3004_HOME

English-8
7. MONITORING
If the DVR set is connected to the Internet in normal
network settings, you can set the DVR’s current time in
sync with the selected <Time Server> regularly if you
select to use <Time Server>.
If you want to use the DST functions, set it to ON.
Using a Smartphone
1. Download iPOLiS mobile to your Smartphone.
2. From the start screen of iPOLiS mobile, tap <Device List>.
The Add Device screen appears.
3. Register the DVR to the iPOLiS mobile.
M
`For more information, refer to the user manual.
(http://www.samsungcctv.com)
25
26
Right click the screen or press the [MODE] on the
remote control.
24-1
When the launcher menu appears, press the < >
button.
ÚYou can add or modify the screen transition interval
in “System > Device > Monitor” menu.
24-2
2012-01-01
01:10:25
2012-01-01 01:10:25
Date/Time/Language
Date/Time/Language
Holiday
Date 2012 -01-01 YYYY-MM-DD
Time 08:14:24 24 Hours
Time Zone GMT+08:00
Time Sync. Setup Not Used
DST Dec First (Sun) 0H Dec First (Sun) 0H
Language English
OK Cancel
Time Synchronization Setup
OK Cancel
Synchronization Use
Time Server 203.248.240.103
Last Sync Time Fail
Activate as Server Use
1.X