Sanctuary SA-PV2M User manual

IMPORTANT:
Please read this information and follow all safety rules carefully before
operating your gun safe. Failure to do so will void your warranty.
072921
HOME & OFFICE SECURITY VAULTS
INSTRUCTION MANUAL FOR
SA-PV2M and SA-PV3L

TABLE OF CONTENTS
www.saproducts.com 1
IMPORTANT INFORMATION ............................................................................................... 2
1. REGISTRATION ................................................................................................................ 3
2. UNDERSTANDING YOUR VAULT ..................................................................................... 4
3. INITIAL ENTRY .................................................................................................................. 5
4. BATTERY INSTALLATION .................................................................................................. 5
5. ELECTRONIC LOCK SECURITY CODE SETUP ...................................................................... 6
6. LOW BATTERY WARNING ............................................................................................... 7
7. SILENT ENTRY .................................................................................................................. 7
8. LOCKOUT MODE/TAMPER PROTECTION ......................................................................... 8
9. LOCKED OUT OF YOUR VAULT ....................................................................................... 8
10. PROPER PLACEMENT AND MOVING OF VAULT ............................................................. 8
11. SECURING YOUR VAULT ................................................................................................ 9
12. MAINTAINING HINGES AND INTERNAL MECHANISMS .............................................. 10
THREE YEAR WARRANTY ................................................................................................... 11

2
DISCLAIMER - READ BEFORE VAULT SETUP
WEAPON STORAGE
SAFETY
Thank you for choosing a Sanctuary vault to protect your valuables. We are
commied to securing, organizing and protecng your most important documents,
valuables and keepsakes.
If you experience problems or challenges with your vault, please contact us.
Many issues can be quickly resolved without the product being returned.
Be sure to keep backup keys stored in a safe place away from unauthorized users
Do not put anything in your vault that will put pressure against the door when
it is closed.
If you choose to ulize this vault to store a weapon always follow proper weapon and
local laws.
SA Consumer Products strongly recommends that you do not store loaded firearms.
Always follow the firearm safety rules set out by the firearm’s manufacturer.
Store ammunion separately from valuables.
A Sanctuary vault or any other firearm storage device cannot take the place
of other safety procedures including advising children of the dangers of firearms.
SA Consumer Products and its distributors of the Sanctuary vaults do not
recommend, suggest, advise, promote, or otherwise condone the ownership or use of
firearms. We believe the decision to own or use a firearm is a serious decision that
should only be made by an adult who has carefully considered the risks and benefits
of such a decision.
PLEASE READ THIS INFORMATION CAREFULLY BEFORE OPERATING YOUR
SANCTUARY VAULT.
DO NOT LOCK THIS MANUAL OR THE BACKUP KEYS IN YOUR VAULT.
Contact Customer Service at [email protected] or [phone]

3
Register your vault at www.saproducts.com
PURCHASE DATE:
PURCHASE PRICE (BEFORE TAX):
MODEL NUMBER:
SERIAL NUMBER:
KEY NUMBER (IF APPLICABLE):
1. REGISTRATION
RETAILER NAME:
By registering your Sanctuary vault we will be able to expedite and address
any problems or challenges you may have which would otherwise require a
notary leer and proof of payment.
The informaon you record onto this page will be required in the event you
cannot access the contents of your Sanctuary vault. Please fill out all the required
informaon below and retain for your records and safe keeping.
PLEASE HAVE THIS INFORMATION READY PRIOR TO CALLING FOR TECHNICAL
ASSISTANCE AT:
Contact Customer Service at [email protected] or [phone]
REGISTRATION INFORMATION

4
SA-PV2M
SA-PV3L
Knob
Locking
Bolts
Key
Hooks
Removable
Shelf Battery
Compartment
Reset Button
(Under Cover)
2. UNDERSTANDING YOUR VAULT
Backup Key Entry
(Under Cover)
Security Cable
Port Entry
Electronic
Touch Pad
Knob
Electronic
Touch Pad
Backup Key Entry
(Under Cover)
Removable
Shelf
1234
5678
*90#
1234
5678
*90#
Battery
Compartment
Key
Hooks
Reset Button
(Under Cover)
Locking
Bolts
Security
Cable
Bolt Down Holes
(Under Foam)
Bolt Down Holes
(Under Foam)

5
4. BATTERY INSTALLATION
12
56
*
9
Step 1
Step 2
LOCK UNDER
KEY COVER
3. INITIAL ENTRY
1.
2.
Locate the key cover on the
lockface and remove carefully
by pulling the key cover tab.
In the future you may place
a flat head screw driver in the
slot and pry upwards.
Insert the backup key. Turn
and hold the key counter-
clockwise, then turn the
knob on the door clockwise
to grant access to your
vault.
Step 1
1.
BATTERY BOX
Locate the (4) AA baeries
and insert in the baery
compartment on the inside of
the door panel as shown.
Touch pad will beep (1) me
when baeries are
successfully installed.
Replace the baery cover.
WARNING: The baeries must be inserted with the correct polarity. Exhausted baeries
must be removed from the product and discarded safely. Do not mix old and new baeries.
Do not mix alkaline or standard (carbon – zinc) baeries. Do not use rechargeable (nickel –
cadmium) baeries.
1234
5678
*90#
1234
5678
*90#

6
4
8
#
Important: Your vault comes with a factory preset code of 159#. It is necessary
to re-program your vault with a new security code you have personally selected
to provide maximum security. Be careful, in choosing your new security
code, you’ll want to be sure that you can operate the unit quickly without
making an error.
5. ELECTRONIC LOCK SECURITY CODE SETUP
3.
1. First, remove the black rubber
plug that covers the reset buon
on the door panel.
2. Use a pen p to press the reset
buon. You will hear 1 beep and
the green unlock LED flashes
once.
NOTE: Recording mode will me out
aer 10 seconds of inacvity. If this
occurs press restart buon and
begin again.
Step 2 Step 1
Reset buon located
inside plasc housing
Step 1
Step 3
Input your new 3-8 digit code
followed by the (*) buon.
If successful, you will hear (2)
beeps and the green unlock
symbol will flash on your
keypad.
If unsuccessful, you will hear
(5) beeps and the red lock
symbol will flash on your
keypad. Press the reset buon
and start again.
Once your code is successfully
programmed, input your 3-8
digit code followed by the (#)
for access of your vault.
RED LOCK ICON = TRY AGAIN
GREEN UNLOCK ICON = SUCCESS!

7
1234
5678
*90#
1234
5678
*
90#
6. LOW BATTERY WARNING
7. SILENT ENTRY MODE
By acvang the silent entry mode, the
vault will no longer make audible
sounds.
To turn on silent entry mode, press and
hold the (*) buon for (3) seconds.
The green light will flash twice
indicang the vault is now in silent
entry mode.
To turn the sounds back on, press and
hold the (*) buon for (3) seconds, the
green light will flash twice, indicang
you are no longer in silentry mode.
1234
5678
*
90#
This electronic lock is equipped to alert
you when the baeries are low by
illuminang the orange light (center)
on the touch pad for 10 seconds any me
the touch pad is acvated.
Orange = Low Baery

1234
5678
*90#
8
9. LOCKED OUT OF YOUR VAULT
8. LOCKOUT MODE / TAMPER PROTECTION
In the event you have forgoen the security code your primary acon will be to use
your backup keys in order to gain access to your vault. Follow steps 3, 4 & 5 to
reprogram your vault.
If you have lost your backup keys, you will need to contact customer service at the
number below. Proof of purchase is required to obtain keys.
Contact Customer Service at [email protected] or [phone]
10. PROPER PLACEMENT AND MOVING OF VAULT
1. To maximize burglary protecon and stability,securing the vault to the floor or
wall is recommended.
2.
3. Always ensure the vault is in an isolated and dry area. Never place the vault
direct contact with a wet floor. When installing your vault on a concrete floor,
use of a moisture/protecve barrier is highly recommended. Failure to do so
or exposing the vault to chemicals or other adverse environments may void
the warranty.
SA Consumer Products recommends that you store your vault in a closet,office,
basement,bedroom or any other locaon that is convenient for you but out of
direct line of sight from prying eyes.
1. Three consecuve incorrect code entries will put
the vault in “Basic Lockout” mode. Touch pad is
deacvated for 30 seconds.
2. Aer “Basic Lockout” mode has ended, another
three consecuve incorrect code entries will result
in “Severe Lockout” mode. Touch pad is deacvated
for 5-minutes.

9
11. SECURING YOUR VAULT
1.
2.
SECURING YOUR VAULT WITH PROVIDED CABLE
A security cable is included with
your vault. To secure the cable
around a fixed object, first loop
the cable around the object as
shown in the figure to the right.
Insert the cable’s metal peg end
into the hole on the side of the
vault while sll open.
3. From the inside of the vault, take
the cable clip and push it over the
metal peg unl fully secured. Use
pliers to seat the cable clip if
needed.
Check the loop to ensure their is no way it
can be manipulated to be easily removed
from the fixed object before leaving
unaended.
Step 1 & 2
Step 3
SAFE
INSIDE
CABLE
CLIP
INSIDE OFVAULT,
PUSH CLIP OVER
END OFCABLE

10
12. MAINTAINING HINGES AND INTERNAL MECHANISMS
The hinges and internal locking mechanism are permanently lubricated, thus
needing no maintenance. Opening the door panel of your vault may void your
warranty. Always consult our customer service experts prior to doing so.
11. SECURING YOUR VAULT (CONTINUED)
TOOLS AND HARDWARE NEEDED TO SECURE
VAULT TO A WOOD OR CONCRETE SURFACE:
WASHERS
(NOT INCLUDED)
PADS
(INCLUDED)
LAG BOLTS
(NOT INCLUDED)
ANCHORS
(NOT INCLUDED)
• DRILL
• 3/8�DRILL BIT
( FOR DRILLING ANCHOR HOLE )
or 3/16�(FOR INSTALL W/ OUT ANCHOR)
• SOCKET WRENCH TO MATCH
BOLT HEAD SIZE
• 2 STEEL LAG BOLTS (NOT INCLUDED) - SIZE 1/4" X 1.50" TO 2.0" LONG
• 2 STEEL WASHERS (NOT INCLUDED) - 1/4"
• 2 PLASTIC ANCHORS (NOT INCLUDED)- SIZE #10-12 X 1.5" TO 1.75" LONG
(FOR CONCRETE INSTALLATION)
• 4 PADS (INCLUDED)
Use the recommended hardware or consult your hardware retailer for fastening
hardware for your parcular mounng surface.
Open the vault door to provide access to the factory drilled bolt down holes that
are located under the protecve foam liner.
To secure your vault to the floor, it will first be necessary to mark and drill pilot
holes in the floor surface.
Drill the appropriate diameter and depth of pilot holes based on the type of
hardware being used and the type of floor surface. When mounng on concrete we
recommend using a drill and a concrete drill bit to drill the two corresponding holes
in the mounng surface.
Secure the vault by threading anchor bolts through the factory drilled bolt down
holes in the vault and screw down ght with a ratchet wrench.
BOLT
WASHER
VAULT
FLOOR
MOUNTING
SURFACE
ANCHOR
FOR CONCRETE
INSTALLATION

11
SA Consumer Products will repair or replace, at their sole discreon,
any Sports Afield vault damaged by fire, forced entry, forced aack
or natural flood for the lifeme of the original owner.
SA Consumer Products will repair or replace, at their sole discreon,
any Sports Afield vault with defecve parts, paint or lock for three
years of the original owner purchase date.
If SA Consumer Products deems a replacement vault is to be sent,
they will pay the freight costs to ship the replacement vault to the
original owner.
This three year warranty is limited to the vault and expressly
excludes any loss associated with the contents of the vault.
SA Consumer Products
reserves the right to receive full evidence
of your misfortune, such as a police report and/or homeowner’s
statement of coverage. This warranty is not valid outside of the
United States and Canada.
Proof of registraon and copy of sales receipt must be on file at
the me of claim. Visit our website at www.saproducts.com to
register your vault.
Three year warranty only applies to the original owner of the vault.
SA Consumer Products shall only be responsible and liable when the
vault is used in compliance with the direcons specified in your new
SA Consumer Products owner’s manual.
SA Consumer Products
requires that specific guidelines be
followed for repair. The vault will be repaired in-home if possible
(to include parts and labor); however, if factory replacement
is necessary (at
SA Consumer Products ’ sole discreon), the
replacement will be shipped freight prepaid, curbside delivery.
This warranty is inclusive and is in lieu of any and all other
warranes, express or implied. Specifically excluded are the
warranes of merchantability and fitness for a parcular purpose.
This warranty is limited to the vault itself and/or its value and
does not include consequenal damages of any kind including,
but not limited to, the contents in and of the vault.