S&P VENT-355 Manual

VENT-355
VENT-400
Instrucciones de montaje
Instruction leaflet
Notice de montage
Montageanweisungen
Montage-en gebruiksaanwijzing
Instrucções para a montagem
Istruzioni per l'installazione
Användar instruktion
Instrukcja obslugi
Návod
Brugervejledning

Fig.1
ZX Y
UV W
TP TP
VENT-355
VENT-400 1

Fig.2
TP TP
Z
U
X
V
Y
W
TP
K
K
TP
K
N
L
VENT-355
VENT-400 1

Fig.3
TP
ZXY
UVW
TP
VENT-355
VENT-400 3

ENGLISH
Installation and wiring instructions for
VENT in-line duct fans.
IMPORTANT SAFETY INFORMATION
INSTALLATION
ELECTRICAL CONNECTION.
MAINTENANCE
The VENT range of in-line duct extractor fans
has been manufactured has been
manufactured in accordance with the
rigorous standards of production and quality
control laid down by the international Quality
Standard ISO 9001. All components have
been checked and each of the finished
products has been tested at the end of the
manufacturing process.
We recommend that you check the following
when receiving this product:
That is the correct size and model.
That the details on the rating label are
those you require; voltage, frequency,
performance.
The installation should always be carried
out in accordance with all current applicable
Standards to the country in which it is
installed.
The installation should always be carried
out by a suitably qualified and competent
person(s).
These fans are not for stand-alone use.
They are designed to be incorporated into
ducted systems, machines or where safe
operation has been ensured by providing
applicable protection to moving parts.
Do not use this product in, or to extract
from, potentially hazardous or explosive
atmospheres.
If the extractor operates in a room with a
boiler or any other type of appliance requiring
air for combustion, check that air
replacement inlets are sufficiently sized.
The extractor outlet must not be
connected to a duct used to exhaust smoke
or fumes from any appliance that uses gas or
any other type of fuel
This unit must not be installed outside,
unless covered by a suitable weatherproof
enclosure.
Before installing the unit ensure the
impeller is running freely and there are no
obstructions to the airflow.
For installation use the two mounting feet
fitted on the fan.
The fan should always be installed so that
safe operation and maintenance can be
ensured.
In order to avoid losses in performance we
do not recommend that the fan is used in
conjunction with ducting of a lesser diameter
than the fan connection spigots. If the
extractor is connected to flexible ducting,
then the ducting must be expanded as much
as possible.
The fan should be installed to ensure
minimum vibration and noise transmission to
surrounding ductwork and building frames.
Antivibration mountings and sound
attenuating accessories are available.
Please contact your local distributor.
Before Installation and Wiring ENSURE
THE MAINS ELECTRICAL SUPPLY IS
DISCONNECTED!!
Ensure that the voltage and frequency of
the electrical supply match the information
stated on the Data Plate of the unit
(maximum recommended tolerance of
Voltage (V) and Frequency (Hz) ± 5%).
Connect the electrical supply in
accordance with the electrical wiring
diagrams included within this booklet.
Before operation, check all connections
are correct and there are no obstructions to
the airflow.
On connecting the electrical supply
ensure the direction of rotation and airflow
correspond with the direction of airflow /
rotation arrows (sited on unit).
Before inspection or repair, ensure that
the unit is disconnected from the mains
electrical supply.
The fan impeller should be cleaned at
least once (1) a year to ensure trouble free
operation.
Do not clean the unit with strong
detergents or cleaning fluids. Use a damp
(not wet) cloth only for cleaning.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
(Soler & Palau, S.A. reserve the right to alter
specifications without prior notice)