Sanremo F18SB Datasheet

Sanremo F18SB Installation & Quick Start Guide
Disclaimer: Installation must be performed by professional technician. Improper installation can void warranty, permanently damage equipment and/or present burn
& electrical hazard to installer/user. Consult with local municipality for official electrical and plumbing codes/guidelines.
Consult user manual for expanded installation, operation, and safety guidelines.
Dimensions
Water Requirements
Electrical Requirements
2 Group
3 Group
Receptacle & Plug Configuration
•Volts: 220 (voltage range of 208-240) 60Hz
•Single phase / 3 wire (2 hot + 1 ground)
•Watts: 3200
•Amp draw: 15A
•Receptacle / plug: NEMA 6-30
•Plug included
•Volts: 220 (voltage range of 208-240) 60Hz
•Single phase / 3 wire (2 hot + 1 ground)
•Watts: 5650
•Amp draw: 24A
•Receptacle / plug: TBD
•Plug included
2 Group
3 Group

Connection & Counter Hole Diagrams
3” hole in counter recommended for passage of
electrical cord & water/drain lines.
Counter hole placement recommended to be
center of machine and 12.5” inward from edge of
the drip tray.
First start (boiler fill) procedure

Display readout
Pump adjustment
Prepare a portafilter with coffee at the desired dose/grind calibration and insert into the group. Turn group on by
selecting the continuous (SR logo) button, insert stubby screwdriver into pump hole and adjust WHILST the group is
extracting the coffee.
STEAM BOILER TEMPERATURE
OR PRESSURE (USER CAN SET)
STEAM BOILER
WATER LEVEL

Adjusting water mix for hot water tap
Water mix valve located near water pipe connection
Group Volumetric Programming
•Press and hold Sanremo logo (continuous) button on group 1 (left most group) until touchpad LED’s
begin flash and pressure display reads ‘DOSES SETTING SELECT DOSE IN 30 S’.
•Insert coffee prepped portafilter into group and select dose button for programming.
•When desired volumetric dose has been reached, press the same dose button to store volumetric
program.
•Repeat steps 2 & 3 for remaining dose buttons.
•Follow same procedure to program hot water tap dispensing volume.
•When finished, do not touch any of the group buttons for 30 seconds. Machine will then store program
and transfer to the remaining groups.
PRESS AND HOLD TO ENTER
VOLUMETRIC PROGRAMMING

Individual Group Cleaning Mode
Accessing Programming Menu
•Press and hold Sanremo logo (continuous) button on group 1 (left most group) until ‘HEATING CUP’ is read on pressure display.
•If continuous button is released when display reads ‘DOSES SETTING SELECT DOSE IN 30 S’, DO NOT press group buttons or volumetric
programming will be overwritten. Please wait for volumetric programming to time out after 30 seconds (Doses setting message will
disappear from pressure display) and re-try holding the continuous button to enter programming menu.
Programming Menu Options
Cup warmer settings
Barista lights (if equipped)
Eco modes & settings
Fine tune group recipes
Pre-brew settings
Group flush notification to
maintain optimal extraction
temperature
Date/time settings & auto
on/off settings
Machine counters
Deep clean all groups.
*NOTE* Once started, it
cannot be interrupted.
Exit programing
Navigating Programming
Long dose buttons to change category
Short dose buttons will light up when category is
selected. These are used to change category values.
Continuous (Sanremo logo) button to enter categories / store values
HOLD
PRESS

Warranty Terms and Conditions
*** Submit at time of installation ***
Client Name
Date
Machine Model
Machine Serial N°
N°ofGroups
Supply Voltage
Location Address / Type
Install Date
Installed By
Water Quality Report (Before & After Filtration)
TDS:
ppm
Total Hardness:
ppm
pH:
Chlorides:
ppm
Total Alkalinity:
ppm
Total Chlorine:
ppm
Iron:
ppm
TDS:
ppm
Total Hardness:
ppm
pH:
Chlorides:
ppm
Total Alkalinity:
ppm
Total Chlorine:
ppm
Iron:
ppm
Recommended Water Specifications
•
Dedicated cold water line with shut-off valve
•
Minimum incoming line pressure of 29 PSI / 2
BAR and max line pressure of 65 PSI / 4.5 BAR
Total Dissolved Solids (TDS):
30-150 ppm
Total Hardness:
Below 85 ppm
pH:
6.5-8
Chlorides:
*Any presence of Chlorides can causecorrosion*
5-15 ppm
Total Alkalinity:
35-75 ppm
Total Chlorine:
0 ppm
Iron:
0 ppm
Water levels outside of these parameters can void warranty.
Consult with a water filtration professional for water testing
and recommended systems.
E-mail Form and supporting
media to [e-mail]
I have read and acknowledge the above
Client Name:
Client Signature:
Date:
SANREMO Coffee Machines USA
99 Grand Street - Unit 20
Moonachie, NJ 07074 Direct Technical Department Line: 201-856-1705
Water Filtration Make / Model / Details (Please Send Photos of Installation and Filtration Setup)
SANREMO Srl guarantees that the machines and the components
supplied are free from defective material and / or workmanship
for a period of twelve (12) months from invoice date.
The warranty does not cover any faults or malfunctions due to
normal wear and tear, inappropriate use and / or use not in
accordance with normal operation, the use of non-original spare
parts and non-compliance with what is indicated in the use and
maintenance manual delivered together with the machine,
accidental events, unauthorized modifications or adaptations,
tampering, anomalies caused by electrical and hydraulic systems
or inadequate water filtering and insects infestation.
In the case a failure is found; labor, diagnosis fees, travel fees
are not included in the warranty, nor are freight costs in cases of
shipping.
During the warranty period, all parts that are deemed defective
based on the judgment of SANREMO TSD (Technical Service
Department) will be replaced.
SANREMO Srl has the right to make changes to its products at any
time necessary for technical and / or aesthetic reasons, reserving
all rights deriving from these changes.
Consult with Sanremo TSD prior to performing any warranty
repairs.
Terms & Conditions