Sanremo ZOE COMPETITION Datasheet

Sanremo Zoe Competition Installation & Quick Start Guide
Disclaimer: Installation must be performed by professional technician. Improper installation can void warranty, permanently damage equipment and/or present burn
& electrical hazard to installer/user. Consult with local municipality for official electrical and plumbing codes/guidelines.
Consult user manual for expanded installation, operation, and safety guidelines.
Dimensions
Water Requirements
Electrical Requirements
2 Group
3 Group
Recommended Plug Configuration
•Volts: 220 (voltage range of 208-240) 60Hz
•Single phase / 3 wire (2 hot + 1 ground)
•Watts: 3350
•Amp draw: 15A
•Recommended receptacle / plug: NEMA 6-20
•Plug NOT included
•Volts: 220 (voltage range of 208-240) 60Hz
•Single phase / 3 wire (2 hot + 1 ground)
•Watts: 6050
•Amp draw: 25A
•Recommended receptacle / plug: NEMA 6-30
•Plug NOT included
2 Group
3 Group
24”
610
mm

Connection & Counter Hole Diagrams
2.5” hole in counter recommended for passage of
electrical cord & water/drain lines.
Counter hole placement recommended to be 5”
inward from rear of machine & 7” inward from
right of machine.
First start (boiler fill) procedure
Turn main switch to position “1”, allow steam boiler to auto fill, confirm boiler fill was successful and has not timed out.
If touchpad LED’s are flashing, machine has timed out.
If machine has timed out, cycle machine off/on (position “1”) again and allow to auto fill. If machine is still timing out, shut machine
down and re-check the inlet water line / filtration system and confirm water flow to machine.

When the machine has successfully auto filled the steam boiler, turn on all groups and confirm water flow. Once
water is flowing from groups, turn them off and switch to position “2”.
Machine will begin to heat
Volumetric Programming
•Press and hold Sanremo logo (continuous) button on group 1 (left most group) until touchpad LED’s
begin flash.
•Insert coffee prepped portafilter into group and select dose button for programming.
•When desired volumetric dose has been reached, press the same dose button to store volumetric
program.
•Repeat steps 2 & 3 for remaining dose buttons.
•Follow same procedure to program hot water tap dispensing volume.
•When finished, do not touch any of the group buttons for 30 seconds. Machine will then store program
and transfer to the remaining groups.
Group Cleaning Mode
PRESS
HOLD

Warranty Terms and Conditions
*** Submit at time of installation ***
Client Name
Date
Machine Model
Machine Serial N°
N°ofGroups
Supply Voltage
Location Address / Type
Install Date
Installed By
Water Quality Report (Before & After Filtration)
TDS:
ppm
Total Hardness:
ppm
pH:
Chlorides:
ppm
Total Alkalinity:
ppm
Total Chlorine:
ppm
Iron:
ppm
TDS:
ppm
Total Hardness:
ppm
pH:
Chlorides:
ppm
Total Alkalinity:
ppm
Total Chlorine:
ppm
Iron:
ppm
Recommended Water Specifications
•
Dedicated cold water line with shut-off valve
•
Minimum incoming line pressure of 29 PSI / 2
BAR and max line pressure of 65 PSI / 4.5 BAR
Total Dissolved Solids (TDS):
30-150 ppm
Total Hardness:
Below 85 ppm
pH:
6.5-8
Chlorides:
*Any presence of Chlorides can causecorrosion*
5-15 ppm
Total Alkalinity:
35-75 ppm
Total Chlorine:
0 ppm
Iron:
0 ppm
Water levels outside of these parameters can void warranty.
Consult with a water filtration professional for water testing
and recommended systems.
E-mail Form and supporting
media to [e-mail]
I have read and acknowledge the above
Client Name:
Client Signature:
Date:
SANREMO Coffee Machines USA
99 Grand Street - Unit 20
Moonachie, NJ 07074 Direct Technical Department Line: 201-856-1705
Water Filtration Make / Model / Details (Please Send Photos of Installation and Filtration Setup)
SANREMO Srl guarantees that the machines and the components
supplied are free from defective material and / or workmanship
for a period of twelve (12) months from invoice date.
The warranty does not cover any faults or malfunctions due to
normal wear and tear, inappropriate use and / or use not in
accordance with normal operation, the use of non-original spare
parts and non-compliance with what is indicated in the use and
maintenance manual delivered together with the machine,
accidental events, unauthorized modifications or adaptations,
tampering, anomalies caused by electrical and hydraulic systems
or inadequate water filtering and insects infestation.
In the case a failure is found; labor, diagnosis fees, travel fees
are not included in the warranty, nor are freight costs in cases of
shipping.
During the warranty period, all parts that are deemed defective
based on the judgment of SANREMO TSD (Technical Service
Department) will be replaced.
SANREMO Srl has the right to make changes to its products at any
time necessary for technical and / or aesthetic reasons, reserving
all rights deriving from these changes.
Consult with Sanremo TSD prior to performing any warranty
repairs.
Terms & Conditions