SATO CL4NX UHF User manual

First edition: Mar 2014 Q04502000
©2014 SATO CORPORATION
UHF Inlay Configuration Guide
CL4NX UHF Inlay Placement & Configuration Table
This recommendation has been tested successfully at SATO. Results may vary in the actual customer installation due to overall system tolerances. Validation of
functionality in the actual system is therefore recommended.
In no event shall SATO be liable for any faults arising out of use of or inability to use the product.
Position(mm) Power (dBm) (Y=) Standard Antenna Position
(mm)
Region Manufacturer Inlay
[IC Chip] Feed Direction XYSWriteRead
Antenna
Pitch Blue Yellow Green
Alien
Technology
ALN-9640 “Squiggle”
[Alien Higgs3]
47.5-57 3-5 21 24 14 Short - - -
47.5-57 18-36 33 16 7 Standard 18-23 24-29 30-36
Alien
Technology
ALN-9662 “Short”
[Alien Higgs3]
35-45 0-5 23 24 18 Short - - -
35-65 10-24 50 24 16 Standard 10-14 15-20 21-24
Alien
Technology
ALN-9762 “Short”
[Alien Higgs4]
50-60 0-5 20 24 13 Short - - -
50-60 15-22 43 24 10 Standard 15-18 19-22 -
Alien
Technology
ALN-9610 “Squig”
[Alien Higgs3]
22.5-42 2-5 21 24 13 Short - - -
22.5-62 15-24 85 24 15 Standard 15-18 19-24 -
Alien
Technology
ALN-9710 “Squig”
[Alien Higgs4]
22.5-62 3-6 21 24 15 Short - - -
22.5-37 14-28 80 23 20 Standard 14-18 19-24 25-28
Alien
Technology
ALN-9720 “HiScan”
[Alien Higgs4]
19.5-59 0-3 31 24 18 Short - - -
34.5-59 14-32 80 24 17 Standard 14-17 18-24 25-32
Alien
Technology
ALN-9654 “G Tag”
[Alien Higgs3]
46.5-56.5 1-10 25 20 17 Short - - -
46.5-61.5 14-30 58 14 10 Standard 14-18 19-24 25-30
Alien
Technology
ALN-9728
“Garment Tag”
[Alien Higgs4]
22.5-37.5 0-5 36 23 15 Short - - -
22.5-62.5 6-19 105 24 18 Standard 6-9 10-14 15-19
Alien
Technology
ALN-9728-90
“Garment Tag”
[Alien Higgs4]
- - - - - Short - - -
15-35 24-37 85 18 10 Standard -24-30 31-37
Alien
Technology
ALN-9730 "Squiglette"
[Alien Higgs 4]
- - - - - Short - - -
55 17-24 26 24 11 Standard 17-20 21-24 -
Alien
Technology
ALN-9630 "Squiglette"
[Alien Higgs 3]
40-55 0-4 22 24 16 Short - - -
40-70 15-33 59 24 17 Standard 15-23 24-28 29-33
Arizon AZ-9762
[Alien Higgs4]
35-50 0-3 25 24 19 Short - - -
40-65 11-36 48 24 17 Standard 11-19 20-28 29-36
Avery
Dennison
AD-110m5
[Impinj Monza5]
21.5-46.5 4-11 22 24 16 Short - - -
36.5-46.5 11-32 65 24 20 Standard 11-17 18-25 26-32
I-Mark
In order to successfully configure your CL4NX UHF printer,
you will need the following information about your label. X: Liner Edge to Center of Chip
Y: Optimum Encoding Position*
S: Minimum Inlay Separation
*Y: Measured from tail edge of I-mark to lead edge of inlay when
I-mark sensor is used.
Measured from lead edge of label to edge of inlay when Gap
sensor is used.
Position(mm) Power (dBm) (Y=) Standard Antenna Position
(mm)
Region Manufacturer Inlay
[IC Chip] Feed Direction XYSWriteRead
Antenna
Pitch Blue Yellow Green
Alien
Technology
ALN-9640 Squiggle
[Alien Higgs3]
47.5-57 3-5 21 24 14 Short - - -
47.5-57 18-36 33 16 7 Standard 18-23 24-29 30-36
Alien
Technology
ALN-9662 Short
[Alien Higgs3]
35-45 0-5 23 24 18 Short - - -
35-65 10-24 50 24 16 Standard 10-14 15-20 21-24
Alien
Technology
ALN-9762 Short
[Alien Higgs4]
50-60 0-5 20 24 13 Short - - -
50-60 15-22 43 24 10 Standard 15-18 19-22 -
The value of “Y” will affect printer configuration of
Antenna Selection and Antenna Position.
Feed direction will affect encoding.
This is signified using the inlay
images in the following table.
Standard Antenna Position determined by value of Y.
When Antenna Pitch is “Short”, Standard Antenna Position
can be set to any position; “Blue”, “Yellow”, or “Green”.
Feed Direction
The arrow in the header of table
indicates the direction in which labels
are output from the printer.
Placement and Configurations
globally valid with minor variation.
Valid for Frequencies that fall
within the FCC range, 902-928MHz
CL4NX_Inlay_CG.fm Page 39 Monday, March 10, 2014 7:53 PM

For inlays not included on this list, please contact your local SATO dealer or sales office.
www.satoworldwide.com
• Squiggle and Higgs are trademarks or registered trademarks of Alien Technology Corporation in the U.S. and other countries.
• Monza is registered trademark of Impinj, Inc.
Avery
Dennison
AD-171m5
[Impinj Monza5]
13.5-53.5 7-10 18 24 16 Short - - -
13.5-23.5 11-35 60 24 19 Standard 11-18 19-27 28-35
Avery
Dennison
AD-227m5
[Impinj Monza5]
47.5-57.5 0-10 31 24 19 Short - - -
47.5-57.5 13-36 38 16 11 Standard 13-20 21-28 29-36
Avery
Dennison
AD-232iL
[NXP UCODE G2iL]
- - - - - Short - - -
45-70 12-35 62 24 16 Standard 12-19 20-27 28-35
Avery
Dennison
AD-233m5
[Impinj Monza5]
40-55 0-4 24 24 19 Short - - -
40-70 15-37 63 23 17 Standard 15-21 22-29 30-37
Avery
Dennison
AD-235u7
[NXP UCODE 7]
35-50 0-5 20 24 12 Short - - -
35-65 10-40 59 19 12 Standard 10-20 21-30 31-40
Avery
Dennison
AD-318m5
[Impinj Monza5]
21-46 0-3 31 24 19 Short - - -
31-61 11-31 52 23 19 Standard 11-17 18-24 25-31
Avery
Dennison
AD-370u7
[NXP UCODE 7]
- - - - - Short - - -
18.5-48.5 67-90 86 17 14 Standard 67-79 80-90 -
Avery
Dennison
AD-224iL
[NXP UCODE G2iL]
47.5-57.5 0-10 24 24 19 Short - - -
47.5-62.5 16-37 41 24 15 Standard 16-22 23-29 30-37
Avery
Dennison
AD-317iL
[NXP UCODE G2iL]
- - - - - Short - - -
35.5-60.5 10-33 50 24 16 Standard 10-17 18-25 26-33
Avery
Dennison
AD-236u7
[NXP UCODE 7]
40-70 0-7 24 24 16 Short - - -
40-50 8-31 37 18 8 Standard 8-15 16-23 24-31
SMARTRAC DogBone i
[NXP UCODE G2iL/iM]
- - - - - Short - - -
44-59 1-30 50 24 9 Standard 1-10 11-2 0 21-30
SMARTRAC Short Dipole i
[NXP UCODE G2iL/iM]
- - - - - Short - - -
46.5-56.5 14-34 45 24 11 Standard 14-20 21-27 28-34
SMARTRAC
Short Dipole M4
[Impinj Monza4
(E/D/QT)]
46.5-56.5 0-1 16 24 13 Short - - -
46.5-56.5 12-36 48 24 15 Standard 12-20 21-28 29-36
SMARTRAC Belt M5
[Impinj Monza5]
35-40 0-3 23 24 16 Short - - -
40-70 11-35 60 24 13 Standard 11-18 19-26 27-35
SMARTRAC MiniWeb
[NXP UCODE G2iL/iM]
- - - - - Short - - -
45-60 18-35 47 24 12 Standard 18-23 24-29 30-35
SMARTRAC Web I
[NXP UCODE G2iL]
17.5-22.5 5-8 61 24 12 Short - - -
12.5-27.5 34-49 93 24 12 Standard -34-41 42-49
SMARTRAC WebLite
[Impinj Monza5]
23-33 0-5 36 24 23 Short - - -
33-63 14-37 45 23 18 Standard 14-21 22-29 30-37
SMARTRAC Viper
[Impinj Monza4D]
55 0-10 20 24 16 Short - - -
55 15-35 25 10 7 Standard 15-21 22-28 29-35
SMARTRAC
Frog 3D
[Impinj Monza4
(E/D/QT)]
25-30 3-6 60 24 19 Short - - -
25-40 7-36 82 20 17 Standard 7-16 17-26 27-36
SMARTRAC Belt
[NXP UCODE G2iL]
- - - - - Short - - -
50-55 16-36 41 24 15 Standard 16-22 23-29 30-36
SMARTRAC Dogbone
[Impinj Monza 5]
- - - - - Short - - -
43-58 13-31 36 8 8 Standard 13-19 20-25 26-31
SMARTRAC ShortDipole
[Impinj Monza 5]
46-56 0-3 19 20 18 Short - - -
46-61 20-34 31 10 9 Standard 20-24 25-29 30-34
Invengo Invengo Great Wall
[Impinj Monza5]
47-62 0-2 30 24 20 Short - - -
47-57 11-37 36 18 15 Standard 11-19 20-28 29-37
Invengo Invengo xWing
[Impinj Monza5]
34.5-49.5 2-4 25 24 18 Short - - -
39.5-64.5 7-34 54 20 19 Standard 7-15 16-24 25-34
CHECKPOINT Champion-M5
[Impinj Monza5]
40-45 0-2 27 24 19 Short - - -
40-70 8-35 58 20 20 Standard 8-16 17-25 26-35
CHECKPOINT WindAparrel-M5
[Impinj Monza5]
30-45 8-11 46 23 20 Short - - -
30-65 19-41 82 16 13 Standard 20-26 27-34 35-41
Position(mm) Power (dBm) (Y=) Standard Antenna Position
(mm)
Region Manufacturer Inlay
[IC Chip] Feed Direction XYSWriteRead
Antenna
Pitch Blue Yellow Green
CL4NX_Inlay_CG.fm Page 40 Monday, March 10, 2014 7:53 PM