Savin 1515 User manual

Printer/Scanner Unit
Type 1515
Operating Instructions
Printer Reference 1
***
C
1
-C
li
ent-
350
.t
if*
Read this manual carefully before you use this product and keep it handy for future reference.
For safe and correct use, please be sure to read the Safety Information in the "Copy Refer-
ence" before using the machine.
Getting Started
Preparing to Print

Printer/Scanner Unit Type 1515 Operating Instructions Printer Reference 1
Printed in China
EN USA B683-8592

Introduction
This manual describes detailed instructions on the operation and notes about the use of this machine.
To get maximum versatility from this machine all operators are requested to read this manual carefully
and follow the instructions. Please keep this manual in a handy place near the machine.
Important
Contents of this manual are subject to change without prior notice. In no event will the company be li-
able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-
ating the machine.
Caution:
Use of controls or adjustments or performance of procedures other than those specified in this manual
might result in hazardous radiation exposure.
Two kinds of size notation are employed in this manual. With this machine refer to the inch version.
Trademarks
Microsoft®, Windows®and Windows NT®are registered trademarks of Microsoft Corporation in the
United States and/or other countries.
Adobe®, PostScript®, Acrobat®, PageMaker®and Adobe Type Manager are registered trademarks of
Adobe Systems Incorporated.
PCL®is a registered trademark of Hewlett-Packard Company.
AppleTalk, Apple, Macintosh and Mac are registered trademarks of Apple Computer, Incorporated.
IPS-PRINT™ Printer Language Emulation Copyright©2000, Oak Technology, Inc., All Rights Reserved.
UNIX is a registered trademark in the United States and other countries, licensed exclusively through
X/Open Company Limited.
Bluetooth is a Trademark of the Bluetooth SIG, Inc. (Special Interest Group) and licensed to RICOH
company limited.
Copyright © 2001 Bluetooth SIG, Inc.
The Bluetooth Trademarks are owned by Bluetooth SIG, Inc. USA
Other product names used herein are for identification purposes only and might be trademarks of their
respective companies. We disclaim any and all rights to those marks.
The proper names of the Windows operating systems are as follows:
• The product name of Windows®95 is Microsoft®Windows®95
• The product name of Windows®98 is Microsoft®Windows®98
• The product name of Windows®Me is Microsoft® Windows® Millennium Edition (Windows Me)
• The product name of Windows®2000 are as follows:
Microsoft®Windows®2000 Advanced Server
Microsoft®Windows®2000 Server
Microsoft®Windows®2000 Professional
• The product name of Windows®XP are as follows:
Microsoft®Windows®XP Professional
Microsoft®Windows®XP Home Edition
• The product names of Windows ServerTM 2003 are as follows:
Microsoft®Windows ServerTM 2003 Standard Edition
Microsoft®Windows ServerTM 2003 Enterprise Edition
Microsoft®Windows ServerTM 2003 Web Edition
• The product name of Windows®NT are as follows:
Microsoft®Windows NT®Server 4.0
Microsoft®Windows NT®Workstation 4.0
Notes:
Some illustrations in this manual might be slightly different from the machine.
Certain options might not be available in some countries. For details, please contact your local dealer.

Note to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursu-
ant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equip-
ment does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one more of
the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
Caution (in case of IEEE1284 environment) :
Properly shielded and grounded cables and connectors must be used for connections to host computer
(and/or peripheral) in order to meet FCC emission limits.
Use a commercially available shielded cable.
Caution (in case of 100BaseTX environment):
Network interface cable with ferrite core must be used for RF interference suppression.
Use a commercially available cable after attaching the ferrite core provided.
Caution (in case of IEEE1394 environment):
Use the cable provided with the machine.
Caution (in case of USB2.0 environment):
Use a commercially available shielded USB cable.
Declaration of Conformity
Product Name: Printer Controller
Model Number: Printer/Scanner Unit Type 1515
Responsible party: Ricoh Corporation
Address: 5 Dedrick Place, West Caldwell, NJ 07006
Telephone number: 973-882-2000
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference, and
this device must accept any interference received,
including interference that may cause undesired operation.
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Copyright © 2004

i
Manuals for This Machine
The following manuals describe the operational procedures of this machine. For
particular functions, see the relevant parts of the manual.
Note
Manuals provided are specific to machine type.
Adobe Acrobat Reader is necessary to view the manuals as a PDF file.
Two CD-ROMs are provided:
• CD-ROM 1“Operating Instructions for Printer/Scanner”
• CD-ROM 2“Scanner Driver & Document Management Utilities”
General Settings Guide
Provides an overview of the machine and describes System Settings (paper
trays, Key Operator Tools, etc.), and troubleshooting.
Refer to this manual for Address Book procedures such as registering fax
numbers, e-mail addresses, and user codes.
Network Guide (PDF file - CD-ROM1)
Describes procedures for configuring the machine and computers in a net-
work environment.
Copy Reference
Describes operations, functions, and troubleshooting for the machine’s copier
function.
Facsimile Reference <Basic Features>
Describes operations, functions, and troubleshooting for the machine’s fac-
simile function.
Facsimile Reference <Advanced Features>
Describes advanced functions and settings for key operators.
Printer Reference 1 (this manual)
Describes system settings and operations for the machine’s printer function.
Printer Reference 2 (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine’s print-
er function.
Scanner Reference (PDF file - CD-ROM1)
Describes operations, functions, and troubleshooting for the machine’s scan-
ner function.

ii
Manuals for DeskTopBinder V2 Lite
DeskTopBinder V2 Lite is a utility included on the CD-ROM labeled “Scanner
Driver & Document Management Utilities”.
• DeskTopBinder V2 Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, and the operating environment for DeskTop-
Binder V2 Lite in detail. This guide can be displayed from the [Setup]dia-
log box when DeskTopBinder V2 Lite is installed.
• DeskTopBinder V2 Introduction Guide (PDF file - CD-ROM2)
Describes operations of DeskTopBinder V2 Lite and provides an overview
of its functions. This guide is added to the [Start]menu when DeskTop-
Binder V2 Lite is installed.
•AutoDocumentLinkGuide (PDF file - CD-ROM2)
Describes operations and functions of Auto Document Link installed with
DeskTopBinder V2 Lite. This guide is added to the [Start]menu when
DeskTopBinder V2 Lite is installed.
Manuals for ScanRouter V2 Lite
ScanRouter V2 Lite is a utility included on the CD-ROM labeled “Scanner
Driver & Document Management Utilities”.
• ScanRouter V2 Lite Setup Guide (PDF file - CD-ROM2)
Describes installation of, settings, and the operating environment for Scan-
Router V2 Lite in detail. This guide can be displayed from the [Setup]dia-
log box when ScanRouter V2 Lite is installed.
• ScanRouter V2 Lite Management Guide (PDF file - CD-ROM2)
Describes delivery server management and operations, and provides an
overview of ScanRouter V2 Lite functions. This guide is added to the [Start]
menu when ScanRouter V2 Lite is installed.
Other manuals
• PostScript 3 Supplement (PDF file - CD-ROM1)
• UNIX Supplement (available from an authorized dealer, or as a PDF file on
our Web site)

iii
TABLE OF CONTENTS
Manuals for This Machine......................................................................................i
How to Read This Manual .....................................................................................1
1. Getting Started
Control Panel..........................................................................................................3
Reading the Display and Using Keys.........................................................................4
2. Preparing to Print
Preparing the Machine ..........................................................................................6
Connecting the Machine ............................................................................................6
Setting Paper on the Bypass Tray .............................................................................8
Installing the Software.........................................................................................13
Auto Run..................................................................................................................13
Quick Install..............................................................................................................14
Installing the PCL 6/5e and RPCS™ Printer Driver.................................................16
Setting Up Options - PCL 6/5e and RPCS...............................................................20
Installing the PostScript 3 Printer Driver ..................................................................21
Mac OS - Installing the PostScript 3 Printer Driver and Utilities...............................27
Mac OS X - Installing the PostScript 3 Printer Driver...............................................29
Installing the Printer Driver Using USB....................................................................30
Installing the Printer Driver Using IEEE 1394 ..........................................................32
Installing SmartDeviceMonitor for Client/Admin.......................................................35
Installing Font Manager 2000...................................................................................35
Using Adobe PageMaker Version 6.0, 6.5, or 7.0....................................................36
Software and Utilities Included on the CD-ROM...............................................37
Printer Drivers..........................................................................................................37
Software and Utilities ...............................................................................................38
INDEX......................................................................................................... 40

iv

1
How to Read This Manual
Symbols
In this manual, the following symbols are used:
R
WARNING:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, could result in death or serious injury.
R
CAUTION:
This symbol indicates a potentially hazardous situation which, if instructions
are not followed, may result in minor or moderate injury, or damage to proper-
ty.
* The statements above are notes for your safety.
Important
If this instruction is not followed, paper might misfeed, originals might be dam-
aged, or data might be lost. Be sure to read this.
Preparation
This symbol indicates prior knowledge or preparation is required before opera-
tion.
Note
This symbol indicates precautions for operation, or actions to take after mal-op-
eration.
Limitation
This symbol indicates numerical limits, functions that cannot be used together,
or conditions in which a particular function cannot be used.
Reference
This symbol indicates a reference.
[]
Keys and buttons that appear on the computer's display.
[]
Keys that appear on the machine's display.
{}
Keys built into the machine's control panel.
{}
Keys on the computer's keyboard.

2
Names of Major Components and Software
The following software products are referred to using a general name:
• DeskTopBinder V2 Lite and DeskTopBinder V2 professional→DeskTop-
Binder V2 Lite/professional
• ScanRouter V2 Lite and ScanRouter V2 professional (optional)→ScanRouter
V2 Lite/professional

3
1. Getting Started
Control Panel
1. {Printer}key
Press to activate the printer function.
2. Indicators
Displays errors and machine status.
h: Error indicator. See Network Guide
and General Settings Guide.
B: Load Paper indicator. See Copy Refer-
ence.
D: Add Toner indicator. See Copy Refer-
ence.
3. Display
Displays operation status and messages.
4. Selection keys
Correspond to items on the display. Press
to select the corresponding item.
5. Scroll keys
Press to select an item.
{U}: scroll upward
{T}: scroll downward
{V}: scroll right
{W}: scroll left
6. {User Tools/Counter}key
Press to change default or operation pa-
rameters according to requirement.
7. {Clear/Stop}key
Clear: clears an entered numeric value.
8. Main power indicator and On in-
dicator
The main power indicator lights when
the main power switch is turned on. The
On indicator lights when the operation
switch is turned on.
9. Operation switch
Press to turn the power on. The On indi-
cator lights. To turn the power off, press
again.
Note
This key is inactivate during printing
or while setting printer defaults.
10. {Online}key
Press to switch the printer between on-
line and offline.
11. Data In indicator
Blinks while the printer is receiving data
from a computer. Lights when there is
data remaining to be printed.
12. {Cancel}key
Press to cancel an operation or return to
the previous display.
13. {OK}key
Press to set a selected item or entered nu-
meric value.
14. Number keys
Press to enter numeric values.
ABW024S
21345678
9
13 14121110
ABW
024
S.eps

Getting Started
4
1
Reading the Display and Using Keys
This section explains how to read the display and using the selection key for the
initial display.
Note
The copy display is set as the default screen when the machine is turned on.
You can change the settings in [System Settings]. See General Settings Guide.
1. Selection keys
Correspond to the function items at the
bottom line on the display.
Example: Basic screen
When the instruction "press [JobReset]"
appears in this manual, press the center
selection key.
2. {Cancel}key
Press to cancel an operation or return to
the previous display.
3. {OK}key
Press to set a selected item or entered nu-
meric value.
4. Scroll keys
Press to move the cursor in each direc-
tion, step by step.
When the {U}, {T}, {V}, or {W} key ap-
pears in this manual, press the scroll key
of the same direction.
OK
ABW021S1
123
4
ABW
021
S
1
.eps

5
2. Preparing to Print
This section gives instructions for connecting the machine and computer, config-
uring the machine, and installing software.
When operating the machine with a USB connection, parallel connection, or IEEE
1394 (SCSI print) connection
• Connect the machine and computer using a USB cable, a parallel cable, or
an IEEE 1394 (SCSI print) cable.
Reference
For more information, see p.6 “Connecting the Machine”.
• Install a printer driver from the CD-ROM.
Reference
For more information, see p.13 “Installing the Software”.
When operating the machine under a network environment
• Configure the network using the machine's control panel.
Reference
For more information, see "Network Configuration", Network Guide.
• Install a printer driver and other utilities from the CD-ROM.
Reference
For more information, see p.13 “Installing the Software”.
Note
"Network environment" describes a situation where the machine is connected
to a computer via Ethernet, wireless LAN, or IEEE 1394 (IP over 1394).

Preparing to Print
6
2
Preparing the Machine
Connecting the Machine
Reference
For information about connection
using Ethernet and wireless LAN,
see "Confirming the Connection",
Network Guide.
For information about connection
using BluetoothTM, see the manual
that comes with the optional Blue-
tooth interface unit.
Requirements
Before using this machine, make sure
all environmental and electrical re-
quirements are met. Connect the ma-
chine to the host computer using the
USB port, network interface unit, or
both.
Make sure all cables, connectors, and
electrical outlets necessary to attach
the machine to the host computer or
network are at hand.
Connecting the Machine to the host
using a USB cable
You can connect the machine to the
host computer using a USB interface
cable.
This machine does not come with a
USB interface cable. Make sure you
purchase the appropriate cable for the
machine and your computer.
Follow the procedure below to con-
nect the machine to the host computer
using a USB interface cable.
AConnect the USB 2.0 interface ca-
ble to the USB port on the right
side of the machine's back cover.
BConnect the other end to the USB
port on the host computer.
The machine and computer are
now connected. The printer driver
must be installed next. For details
about how to install the printer
driver, see p.13 “Installing the Soft-
ware”.
Note
The USB 2.0 interface is sup-
ported by Windows 98 SE/Me,
Windows 2000/XP, Mac OS 9.x,
and Mac OS X.
• For Windows 98 SE/Me:
Make sure to install “USB
Printing Support”. If USB 2.0
is used with Windows 98
SE/Me, only a speed equal to
that of USB 1.1 is possible.
•ForMacintosh:
Macintosh supports only
USB 1.1. If USB 2.0 is used
with a Macintosh, only a
speed equal to that of USB 1.1
is possible.
ABW016S1
ABW
016
S
1
.eps

Preparing the Machine
7
2
Connecting the Machine to the host
using the parallel cable/IEEE 1394 (SCSI
print) cable
Connect the machine to the host com-
puter using the optional IEEE 1284 in-
terface board or optional IEEE 1394
interface board. This machine does
not come with a parallel cable to con-
nect the machine to the host comput-
er.
The machine's parallel interface is a
standard bidirectional interface. It re-
quires an IEEE 1284 compliant Micro
Centronics 36 Pin Cable and a parallel
port on the host computer. Make sure
you purchase the appropriate cable
for the machine and your computer.
Note
Do not use a parallel cable that is
longer than 3 meters (10 feet).
Rating voltage of the interface con-
nector: Max. DC 5V
Follow the procedure below to con-
nect the machine to the host comput-
er.
Important
Before connecting the machine to a
computer using a parallel interface
cable, make sure the machine is
idle, and then turn off both ma-
chine and computer.
Be sure to use a specified interface
cable. Other cables may cause ra-
dio interference.
ATurn off the main power switches
of the machine and computer.
Important
Before turning off the main
power switch, see “Turning Off
the Power”, Copy Reference.
BPlug the cable into the connector
on the machine’s interface.
Parallel Connection
IEEE 1394 (SCSI print) Connection
CPlug the other end of the cable
into the connector on the comput-
er’s interface.
DTurn on the machine's main pow-
er switch.
ETurn on the computer.
Note
When using Windows 95/98
SE/Me/2000/XP or Windows
Server 2003, a printer driver in-
stallation screen might appear
when the computer is turned
on. If this happens, click [Cancel]
on the screen. For more infor-
mation, see p.13 “Auto Run”.
The machine and computer are
now connected. The printer driver
must be installed next. For infor-
mation about how to install the
printer driver, see p.13 “Installing
the Software”.
ABW017S1
ABW
017
S
1
.eps
ABW018S1
ABW
018
S
1
.eps

Preparing to Print
8
2
Setting Paper on the Bypass
Tray
This section gives instructions for set-
ting paper on the bypass tray. Use the
bypass tray to print onto OHP trans-
parencies, labels, thick paper, and en-
velopes that cannot be loaded in the
paper tray.
Reference
For details about setting paper in
the paper tray, see General Settings
Guide.
Note
When loading letterhead paper,
pay attention to its orientation. See
“Orientation-Fixed Paper or Two-
Sided Paper”, Copy Reference.
Paper within the following dimen-
sions can be set in the bypass tray:
• Vertical: 90.0-216.0 mm (3.54 in.-
8.50 in.)
• Horizontal: 139.0-600.0 mm (5.47
in.-23.62 in.)
Be sure to set the paper with the
side you want to print facing down
in the bypass tray.
When loading OHP transparencies
or thick paper in the bypass tray,
make the paper setting using the
control panel or printer driver.
The number of sheets that can be
loaded in the bypass tray depends
on the paper type.
Limitation
The following functions are dis-
abled when printing from the by-
pass tray:
• Duplex Printing
•AutoTraySelect
•AutoTraySwitching
Important
When printing using the printer
function, original images are al-
ways rotated by 180 degrees (the
orientation of images to be printed
is opposite to that of the copier
function). When printing onto pa-
per with specific orientation re-
quirements, such as envelopes and
letterheads, make sure to rotate the
paper feed orientation to 180 de-
grees.
Be sure to set the paper size using
the printer driver when printing
data from the computer. The paper
size set using the printer driver has
priority over the one set using the
control panel.
AOpen the bypass tray.
BAdjust the paper guides to the pa-
per size.
Important
If the paper guides are not flush
against the paper, skewed im-
ages or paper misfeeds might
occur.
ABW019S1
ABW
019
S
1
.eps

Preparing the Machine
9
2
CGently insert paper face down
into the bypass tray.
1. Extender
2. Paper guides
Note
Do not stack paper over the lim-
it mark, otherwise a skewed im-
age or misfeeds might occur.
Open out the extender to sup-
port paper sizes larger than A4
L, 81/2"×11" L.
Fan the paper to get air between
the sheets to avoid a multi-sheet
feed.
When setting an OHP transpar-
ency, make sure that its front
and back sides are properly po-
sitioned.
Select paper type when printing
onto OHP transparencies or
thick paper (over 105g/m2). For
details, see p.11 “Setting thick
paper or OHP transparencies”.
Select paper type when printing
onto envelopes. For details, see
p.12 “Setting envelopes”.
DSelect the paper size.
Note
You can set paper size using the
printer driver. The following
procedures are not necessary
when setting paper size using
the printer driver.
The paper size set using the
printer driver has priority over
that set using the control panel.
When the printer driver is not
used, make settings using the
control panel.
Reference
For printer driver settings, see
the printer driver Help.
For details about setting custom
sizes, see p.10 “Setting custom
size paper”.
APress the {User Tools/Counter}
key.
BSelect [Printer Features]using
{U} or {T}, and then press the
{OK}key.
CSelect [Paper Input]using {U} or
{T}, and then press the {OK}
key.
ABW020S1
ABW
020
S
1
.eps
***
PRN
001
.t
if***
***
PRN
002
.t
if***

Preparing to Print
10
2
DSelect [Bypass Paper Size], and
then press the {OK}key.
ESelect the paper size using {U}
or {T}, and then press the {OK}
key.
Note
When printing onto thick pa-
per or OHP transparencies,
select the paper type. For de-
tails, see p.11 “Setting thick
paper or OHP transparen-
cies”.
FPress the {User Tools/Counter}
key.
Setting custom size paper
Note
Custom sizes can also be set using
the printer driver. The following
procedures are not necessary
when setting custom sizes using
the printer driver.
Custom size settings set using the
printer driver have priority over
those set using the machine's con-
trol panel.
When the printer driver is not
used, make settings using the con-
trol panel.
Reference
For printer driver settings, see the
printer driver Help.
APress the {User Tools/Counter}key.
BSelect [Printer Features]using {U}
or {T}, and then press the {OK}
key.
CSelect [Paper Input]using {U} or
{T}, and then press the {OK}key.
DSelect [Bypass Paper Size], and then
press the {OK}key.
ESelect [Custom Size]using {U} or
{T}, and then press the {OK}key.
FEnter the vertical size of the paper
using the number keys, and then
press the {OK}key.
***
PRN
003
.t
if***
***
PRN
004
.t
if***
PRN
001
.t
if
PRN
002
.t
if
PRN
003
.t
if
PRN
004
.t
if
***
PRN
005
.t
if***

Preparing the Machine
11
2
GEnter the horizontal size of the
paper using the number keys, and
then press the {OK}key.
HPress the {User Tools/Counter}key.
Setting thick paper or OHP
transparencies
Note
Paper settings can also be set using
the printer driver. The following
procedures are not necessary
when setting paper sizes using the
printer driver.
Paper size settings set using the
printer driver have priority over
those set using the machine's con-
trol panel.
When the printer driver is not
used, make settings using the con-
trol panel.
Reference
For printer driver settings, see the
printer driver Help.
APress the {User Tools/Counter}key.
BSelect [System Settings]using {U}
or {T}, and then press the {OK}
key.
CSelect [Tray Paper Settings]using
{U} or {T}, and then press the
{OK}key.
DSelect [Paper Type:Bypass Tray]us-
ing {U} or {T}, and then press the
{OK}key.
ESelect [OHP (Transparency)]or [Thick
Paper]using {U} or {T}, and then
press the {OK}key.
FPress the {User Tools/Counter}key.
Note
Settings made remain valid un-
til they are reset again. After
printing on OHP transparencies
or thick paper, make sure you
clear settings for the next user.
***
PRN
006
.t
if***
PRN
001
.t
if
***
PRN
007
.t
if***
***
PRN
008
.t
if***
***
PRN
009
.t
if***

Preparing to Print
12
2
Setting envelopes
APress the {User Tools/Counter}key.
BSelect [System Settings]using {U}
or {T}, and then press the {OK}
key.
CSelect [Tray Paper Settings]using
{U} or {T}, and then press the
{OK}key.
DSelect [Paper Type:Bypass Tray]us-
ing {U} or {T}, and then press the
{OK}key.
ESelect [Thick Paper]using {U} or
{T}, and then press the {OK}key.
FPress the {Cancel}key twice to re-
turn to the User Tools main menu.
GSelect [Printer Features]using {U}
or {T}, and then press the {OK}
key.
HSelect [Paper Input]using {U} or
{T}, and then press the {OK}key.
ISelect [Bypass Paper Size], and then
press the {OK}key.
JSelect the paper envelope size
from [C6 EnvL][C5 EnvL][DL En-
vL], and then press the {OK}key.
KPress the {User Tools/Counter}key.
***
PRN
010
.t
if***
***
PRN
011
.t
if***
***
PRN
012
.t
if***
***
PRN
013
.t
if***
***
PRN
014
.t
if***
***
PRN
015
.t
if***
***
PRN
016
.t
if***
PRN
004
.t
if