Saxby Lighting Pati User manual

Pati Bricklight
13818
13819
13820

Thank you for purchasing this light fitting.
Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Please retain these instructions for future reference.
Warning
Specification
Installation
Layout
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified
electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
Always use the correct type and wattage bulb. Using the incorrect wattage bulb will damage the bulb and ballast.
When changing a bulb, always switch off at the mains and allow the old bulb to cool down before handling.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
This product is not suitable for dimming.
This product is rated at IP65.
This product is not suitable for location in or near a marine or sea environment.
The entire unit gets hot whilst on for a period of time.
These products should not be fitted to PIR circuits or short duration timed switches. Should you wish to connect
this unit to a timed system please consult the manufacturer before installation.
• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction
box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
• We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber
sheathed cable. The mains supply cable must have a minimum cross sectional area of 1.0mm²
• Cables that are to be in walls must be protected using suitable conduit or plastic trunking.
Voltage: 240V 50Hz a.c.
Lamp: 26W G24d-3 PLC
IP rating: 65
250mm
84mm
96mm
250mm
84mm
96mm
250mm
84mm
96mm
Existing fittings must be completely removed before installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
1. Undo the screws and remove the bezel, glass and seal from the fitting.
2. Cut the mounting hole for the light unit taking care not to damage any pipes or mains cables beneath the
mounting surface 80mm high x 240mm wide x 100mm deep. Remove the mounting box from the fitting and
ensure that it fits correctly in the hole and is level.

You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the connection block.
Wiring
Check That
Commissioning
Having correctly identified the wiring from your existing light fitting, connect to the connection block inside the
product in the following way:
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY LIGHT FITTING
Bezel
Seal
Mounting
Box
Unit
Glass Shade
3. Fit the rear surround into position and secure. This surround may be cemented in position. Wait until the
cement has set before continuing with the installation.
4. Pull the cable through the gland and ensure that it is sealed to ensure that the fitting maintains its IP rating.
5. Place the fitting in position, and secure.
6. Wire as detailed below.
6. Push the unit into the mounting box, ensuring that it sits correctly. Adjust the cable so it does not get snagged.
Refit the screws to hold the unit in place.
7. Refit the seal, shade and bezel. Refit the screws.
8. Replace fuse or circuit breaker and switch on. Your light is now ready for use.

031209
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
For your safety, always switch off the supply before changing lightbulbs, or cleaning.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Saxby Lighting Ltd. NW10 7UL
Care and Cleaning
Recycling Advice
Safety Information
The shade must be replaced immediately should the shade become cracked or damaged. This
tting must not be used without the shade in place.
Replace Cracked
Shade
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
Do not clean the units with a pressure washer.
Fitting / Replacing Bulbs
When changing a bulb, always switch off at the mains and allow the bulb to cool
before handling. Used bulbs should not be disposed of with household waste.
Please recycle where facilities exist. Always use the correct type and wattage bulb.
Using the incorrect wattage bulb will damage the bulb and ballast.
PLC 26W 2 PIN