Saxby Lighting HOXTON RECESSED User manual

www.saxbylighting.com
Instruction manual
90963
HOXTON RECESSED
Saxby Lighting. BH17 7BY
V1 05/12/2019
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before cleaning.
Care and Safety
Technical data
240 V~, 50 Hz
Supply
Voltage:
Bulb
Type: 10.5W LED module (COB), 4000K
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced.
Conformity with all relevant EC Directive requirements.
This product is Class 1, must be connected to earth.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.
This product is rated at IP67.
IP 67
Having correctly identified the wiring from your existing light fitting, pull the mains wire through the hole and connect to the
connection block inside the product in the following way:
Wiring
• You have to correctly identified the wires.
• The connections are tight.
• No loose strands have been left out of the connection block.
Check that...
SUPPLY
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
LIGHTFITTING
BLUE (N)
BROWN (L)
GREEN/YELLOW
• When completed, ensure that there are no bare or loose
strands of wire exposed, and cover all exposed areas of
the connection block with 2 layers of insulation tape.
This LED's are protected by a plastic lens. The lens part must be replaced immediately should
it become cracked or damaged. This fitting must not be used without the plastic lens in place.
Replace Cracked Shade

Warning
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with the IEE Wiring regulations and current Building Regulations.
Check the pack and make sure you have all the parts listed.
To prevent electrocution switch off at the mains supply before installing or maintaining this fitting.
Ensure other persons cannot restore the electrical supply without your knowledge.
This light fitting should be connected to a fused circuit.
If replacing an existing fitting, make a careful note of the connections.
The mains supply cable must have a minimum cross section area of 1.0mm2
Cables must be protected using suitable conduit or plastic trunking.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Take care not to drill into any pipes or mains cables beneath the surface during mounting holes preparation.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
This product is unsuitable for immersion in water.
This product is not suitable for location in or near a marine environment.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully
note the position of each set of wires.
Note that the power needs to be isolated/switched off at the fuse board.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
After deciding the layout of the light fittings ensure that the cables are long enough to connect to desired positions
• Cut a 132.5mm diameter hole in the mounting surface. It is always recommended to cut the hole slightly smaller than the
size specified, and then file the hole until the recessed unit fits snugly.
• Ensure the hole minimum deep void depth of 155mm is available.
• product to sit properly. Take care not to damage any pipes or cables beneath the mounting surface.
• Ensure that adequate room is left for the cable.
• Use a wrench and screwdriver (not provide) to adjust the light source to the desired angle before installation.
( Angle range: turn left 30°and turn right 30°)
• If the unit is to be used in a submerged location, seal the unit into position using silicone sealant.
• If the unit is to be fitted in decking or similar, then secure with a couple of spots of silicone sealant.
• Push the unit into the hole, and adjust the cable so it does not get snagged.
• Power-on. Your light is now ready for use.
1 2 3
Ø 141mm
Ø104mm
158
mm
60mm
See Wiring diagram
Cut a hole Ø132.5mm
Layout
Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction box
and the light fitting.
Avoid locating any cables in positions that would cause a hazard. Position cables and connector bloc away from areas where
they may be at risk from being cut, trapped or damaged.
Decide on the position of the luminaire. Depending on the location, an approved outdoor rated plug and socket may be required.
Alternatively an approved outdoor rated external terminal block may be used.