Saxby Lighting 75270 Manual

• Thissystemcontainsnon-replaceablepartsandcannotbeserviced.Ifdamageoccursthepartshould
bescrapped.
Instructionleaflet
Sentinel Battery PIR Wall Light
www.saxbylighting.com
Foryoursafety,alwaysswitchoffthesupplybeforecleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLightingLtd.BH233PE
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecoulddamagethefinish.
Fitting/replacing bulbs
Iss.121062018
75270
PIR Adjustment
• Theunitmustbeinstalledinavertical position, and
fittedbetween1.8mand2.5mabovetheground.
• The PIR sensor can be adjusted, allowing the
detection distance to be altered to suit the location.
The detection angle is set at 180 degrees. The
durationthat thelamp stayson canbe alteredfrom
10±5 seconds to 60±10 seconds. The detection
distance "SENS" can be adjusted up to 10m Use a
small screwdriver to adjust the ‘TIME’ and ‘SENS’
screws. When adjusting the sensitivity (detection
distance)indaylightitwillbenecessarytocoverthe
sensortosimulatenighttime.
Detection range can be adjusted
by turning 'SENS' screw
Adjustable up to 10 metres
Duration the bulb stays on is
adjustable by turning 'TIME' screw
The sensor trigger point is adjust-
able by turning the ‘LUX’ screw.
Base of product

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
Thisunitcannotbedimmed.
Thisproductcontainsnon-replaceablepartsand
cannotbeserviced.Ifdamageoccurstheproduct
shouldbescrapped.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
ThisproductisratedatIP44.
Thisproductisnotsuitableforlocationinorneara
marineenvironment.
Battery Care:-
- Donotrechargenon-rechargeablebatteries.
-Donotmixoldandnewbatteriesorbatteriesof
differenttypes/brands.
-Donotuserechargeablebatteries.Alwaysremove
exhaustedbatteriesfromtheproduct.
-Alwaysinsertbatterieswiththecorrectpolarity.
-Donotshortthesupplyterminals.
-Thisproductissuitableforusebyadultsonly.
Specification
Voltage: 6V
Lamp: 2x2WLEDModule
IPrating: 44
BatteryType: 4x1.5VAA(notsupplied).
Layout
• Avoidmountingonsurfacessubjecttovibration,as
thismayaffectthePIRsensor.
• Toavoiddamagetotheunit,donotaimthesensor
towardsthesunorareasofstrongelectro-magnetic
disturbances.
• Toavoidnuisancetriggering,thesensorshouldbe
aimedawayfromheatsources,suchasBBQ’s,
Air-Conditioners,otheroutsidelighting,movingcars
andflueventsorreflectivesurfacessuchassmooth
whitewallsorswimmingpools.
• Whenselectinglocation,itisadvisabletonotethat
movementacrossthesensorsfieldismoreeffective
thantowards/awayfromit..
• Decideontheoptimumlocationfortheproduct.Ensurethewalliscapableofholdingtheweightoftheproduct.
• Placetheproductinanuprightposition.
• Detachthewallbackbyremovingthescrewfromthebottomoftheproduct.Setscrewasideforrefittinglater
(Fig.1).
•.Pushbuttonontopofproductandremovewallback(Fig.1).
•.Usingthewallbackasatemplate,markanddrillthepositionofthefixingholes.
• Fixthewallbacktothewallusingthescrewsandwallplugs.Takecaretoavoiddamaginganyconcealed
wiringandpipes.Thecorrectfixingsshouldbeusedforbrickorcavitywalls.
• Removethebatterycasecoverandfitthebatteries.Ensurethe"BatteryCare"warningsonthepreviouspage
arefollowed(Fig.2).
• RefitthebatterycasecoverandthenRefitthescrewssetasideearliersecureinplace.
• SwitchontheproductusingthepushswitchonthefrontoftheproductandadjustthePIRsensorasdetailed
overleaf.Pleasenotethesensorrotatesforeasyaccesstothecontrols.Linethewhitedotsupatthefrontof
theproducttoensurethecorrectorientation.
• Gentlyrotatetheangleoftheshadesbyhandto     
yourpreferredposition.
• Yourlightisnowreadyforuse.
Installation
Fig. 1
Fig. 2
Push