Saxby Lighting ALBA User manual

www.saxbylighting.com
Instruction manual
92529
ALBA SOLAR WALL PIR
Saxby Lighting. BH17 7BY
V1 16/01/2020
Technical data
Sensor Parameters
Bulb
Type: 4.4W LED module (SMD), 4000K
The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole
luminaire shall be replaced.
Conformity with all relevant EC Directive requirements.
Solar Panel: monocrystalline 1.8W
Battery: Li-ion 18650 3.7V 2600mAh
Charge time: 7-8 hours
Detection range: 8±2m
Detection angle: 110º
Waste electrical products should not be disposed of with household waste. Please recycle where facilities
exist. Check with your Local Authority or local store for recycling advice.
We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
Care and Safety
This LED's are protected by a PC shade. The shade part must be replaced immediately should it
become cracked or damaged. This fitting must not be used without the PC shade in place.
Replace Cracked Shade
This product is Class 3.
This product is rated at IP44.
IP 44
This product is rated at IK05.
IK05

Warnings
Please read these instructions carefully before commencing any work.
Check the pack and make sure you have all the parts listed.
All electronic parts fixed already, any intention of opening work-light or changing work-light design is prohibitive unless a
professional electrician.
Do not mix old and new batteries.
Do not mix batteries of different types.
Always insert the batteries with the correct polarity.
Always remove exhausted batteries from the product.
Do not use rechargeable batteries.
Children should not be permitted to use.
The battery should not be opened, destroyed or incinerate, since the may leak or rupture and release to the environment the
ingredients that they contain in the hermetically sealed container. Do not short circuit terminals, or over charge the battery,
forced over-discharge, throw to fire. Do not crush or puncture the battery, or immerse in liquids.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with
your local authority or retailer for recycling advice.
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory
operation of this product. Please retain these instructions for future reference.
Installation
Existing fittings must be completely removed before installation of a new product.
Ensure that the screws and cable entry points are sealed to maintain the IP rating of the product.
Decide on the optimum location for the product. The recommended install height is 1-2 metre, depending on preference and
environment.
Follow the Installation Fig to install:
• Determine the position of your light fitting taking into account the ARROW indicating which WAY UP the base is to be fitted.
Ensure that the mounting surface is solid, preferably a brick or block wall.
• Using the back plate as a template and mark the 2 fixings holes, making sure the the screw holes are horizontal so the
product hangs level. Use plastic plugs and screws to secure the back plate to the wall.
• Ensure the product fix place in.
3S
3S
OFFON
110
Installation Fig
• Press and hold the switch for 3 seconds to turn it off.
• Separate the lamp head from the steel body easily and keep safe for refitting later.
• Unscrewing two screws with a screwdriver.
• Remove the old batteries and replace. Ensure the correct polarity is observed.
• Screwing two screws back into the original position.
• Refit back into the lamp head.
• Press and hold the switch for 3 seconds to turn on. Reset as wanted.
Battery Replacement
2
4
4
2
1
3
2X
3
21
1
2X
Sensor Setting
Mode 1: Press and hold the switch for 3 seconds to turn on, the product will stay on at 45Lm.
Mode 2: After mode 1, press the switch to change to mode 2. Product will stay on at 45LM and increase to 180LM
when motion is detected (This will stay at 180LM for 25 seconds then dim to 45LM and stay lit).
Mode 3: After mode 2, press the switch to change to mode 3. Product will be 400LM when motion is detected and
will turn off after 25 seconds.
Mode 4: Press and hold the switch for 3 seconds to turn it off.
Refer the Installation Fig to set the sensor (please operate after dark):
Once desired setting of sensor has been set, your light is now ready for use.
OFF
＂
3
OFF
400
LUMEN
180
45
LUMEN
LUMEN
Press
Press
＂
3
45 LUMEN
Press and Hold
Press and Hold