Saxby Lighting Aretz GU10 Recessed User manual

Aretz GU10 Recessed
7006GU10

Thank you for purchasing this light fitting.
Please read the instructions carefully before use to ensure safe and satisfactory operation of this product.
Please retain these instructions for future reference.
Warning
Specification
Installation
Layout
Existing fittings must be completely removed before installation of a new product. Before removing the existing
fitting, carefully note the position of each set of wires.
1. Remove the four screws holding the rim in place and set aside. Remove the glass and reflector and set aside.
Undo the screws holding the housing in position
2. Undo the four self tapping screws holding the cast fitting to the plastic housing. Separate the casting from the
housing by pulling gently. Set the cast fitting aside.
• Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the junction
box and the light fitting.
• Avoid locating any cables in positions that would cause a hazard. Position cables and outdoor rated junction
boxes (not supplied) away from areas where they may be at risk from being cut, trapped or damaged.
• We recommend that you use H05RN-F specification cable (not supplied) which is an outdoor grade, rubber
sheathed cable. The mains supply cable must have a minimum cross sectional area of 1.0mm²
• Cables must be protected using suitable conduit or plastic trunking.
Voltage: 240V 50Hz a.c.
Lamp: 1 x 50W Gu10 Halogen
IP rating: 67
158mm
135mm Diameter
Housing
140mm Diameter
129mm
This is a Class 1 product and must be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building Regulations.
To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons
cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified
electrician.
This light fitting should be connected to a circuit with a 30mA RCD fitted.
If replacing an existing fitting, make a careful note of the connections.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
This product cannot be dimmed.
Check with your local authority or retailer for recycling advice.
This product is rated at IP67.
This product is not suitable for location in or near a marine or sea environment.
The entire unit gets hot whilst on for a period of time.

Installation
Wiring
Concrete or Patio Fitting
1. The product must be mounted in the supplied housing. It should not be directly installed in the soil.
2. Form a T shaped cutout to fit the housing into. The dimensions of the housing are given below in Fig. 1. Ensure
that the counterbore at the top is used to hold the housing in position. Ensure that there is adequate drainage
below the product.
3. Position the conduit or plastic trunking at the grooves in the side of the housing (See Fig. 2).
4. Ensure that the cables are not snagged. Screw the fitting to the housing (See Fig. 3).
Decking Fitting
4. Two options can be used to fit this
product into decking.
Option 1 - Drill a 103mm diameter
hole. The product will sit in loose in
position resting on the stainless steel
bezel, but will not be secured. Ensure
that there is enough slack cable to
allow the product to be lifted out
when changing the bulb. The fitting
can be lightly held in position using silicone sealant. Option 2 - Drill a 103mm diameter hole. Machine a
106mm diameter by 10mm deep counterbore. The product will can then be secured.
5. Ensure that conduit or plastic trunking is used to house the cables. Ensure that the cables are not snagged.
6. If using option 2, screw the product in place through the four holes in the housing into the decking (See Fig.
5)
7. Remove the lampholder assembly. Undo the gland at the bottom of the unit and pull the wire through as
shown. Ensure that the wire is fitted correctly in the centre of the gland. Re-assemble the gland, but do not
tighten yet.
8. Connect the supply wires to the product terminal block as shown.
5.4.
135mm
Deck Option 1
28mm
min
107mm
135mm
Deck Option 2
28mm
min
15mm
Check that.....
You have correctly identified the wires.
The connections are tight.
No loose strands have been left out of the
connection block.
Enusre that all cord grips are tightly secured on the
approved outdoor rated external terminal block.
Ensure that all seals are re-fitted correctly to the
approved outdoor rated external terminal block.
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY LIGHT FITTING
2. 1. 3.
29mm
135mm
158mm
105mm
9. Ensure that the wiring is pulled through the gland and then tightened properly. The gasket should form a bead
To wire to another product, punch out the hole for the second gland and fit into place.
10. Ensure that the wire is fitted correctly in the centre of the gland. Re-assemble the gland, but do not tighten yet
(See Fig. 5).
11. Connect the loop supply wires to the product terminal block as shown. Ensure that you have correctly
identified the wires, that the connections are tight and no loose strands have been left out of the connection
block.
12. Refit the lampholder assembly and resecure the screws.

250310
We recommend cleaning with a soft dry cloth.
Do not use solvents or abrasive cleaners as these could damage the finish.
Glass parts - Remove and wash in warm water or just use a damp cloth. Do not use abrasive materials as these
will damage the finish.
To prolong the life and keep your outdoor lighting in good condition, it is recommended that periodically it is
cleaned using a soft cloth followed by the application of a light coating of oil, such as WD40.
Waste electrical products should not be disposed of with household waste. Please recycle where
facilities exist. Check with your Local Authority or retailer for recycling advice.
For your safety, always switch off the supply before maintaing this product.
This system contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped.
Saxby Lighting Ltd. BH23 3PE
Care and Cleaning
Recycling Advice
Safety Information
The shade must be replaced immediately should the shade become cracked or damaged. This
tting must not be used without the shade in place.
Replace Cracked
Shade
Fitting / Replacing Bulbs
Commissioning
6. 6. 8.
10. Locate the casing in the correct position in the housing and secure in place. Refit the reflector.
11. The angle of the bulb can be adjusted in one plane by ±15˚. Set the angle by gently pushing the lampholder to
the desired postion.
12. Refit the glass in position, ensuring that the seals are correctly located. Refit the rim.
13. Replace fuse or circuit breaker and switch on. Your light is now ready for use.
When changing a bulb, always switch off at the mains and allow the bulb to cool before handling. Dispose of used
bulbs carefully. Do not exceed the wattage stated or use a different shape bulb from that indicated on the fitting.
Unscrew the four screws on the front bezel using the supplied tool. Lift off the bezel and glass and set aside.
Push the bulb in to the lampholder and twist anticlockwise to remove. To refit bulb, reverse procedure.
Ensure that the seal is fitted in position with the grooves facing down before refitting decorative bezel.
GU10 240V
50W MAX
GU10 240V
20W MAX
7W MAX GU10
LOW ENERGY LAMP 3W MAX GU10
LED LAMP