Saxby Lighting Bosco 1612T35A Manual

• Whenchangingabulb,alwaysswitchoffatthemains
andallowthebulbtocoolbeforehandling.
• Usedbulbsshouldnotbedisposedofwithhousehold
waste.Pleaserecyclewherefacilitiesexist.Always
usethecorrecttypeandwattagebulb.Usingthe
incorrectwattagebulbwilldamagethebulband
ballast.
• Twist90degreesandremovefromslotstoremove.
• Refitbylocatingthepinsinthelampholderslots,
andtwisting90degreestoengagethepinswiththe
contacts.
• Replacewith:
 1612T35A-2x35WT5Fluorescent
1612T35W-2x35WT5Fluorescent
Fitting/replacing bulbs Instructionleaflet
Bosco
1612T35A,1612T35W
www.saxbylighting.com
Foryoursafety,alwaysswitchoffthesupplybeforechanginglightbulbs,cleaningorremovingshades.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLightingLtd.BH233PE
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecould
damagethefinish.
35W G5 T5
Iss.124062013

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This is a Class 1 product and must be earthed.
Pleasereadtheseinstructionscarefullybefore
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
beforeinstallingormaintainingthisfitting.Ensure
otherpersonscannotrestoretheelectricalsupply
withoutyourknowledge.
Thislightfittingshouldbeconnectedtoafusedcircuit.
Ifreplacinganexistingfitting,makeacarefulnoteof
theconnections.
Alwaysusethecorrecttypeandwattagebulb.Using
theincorrectwattagebulbwilldamagethebulband
ballast.
Whenchangingabulb,alwaysswitchoffatthemains
andallowtheoldbulbtocooldownbeforehandling.
Disposeofusedbulbscarefullyandresponsibly.
Thisproductisnotsuitablefordimming.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
TheseproductsshouldnotbefittedtoPIRcircuitsor
shortdurationtimedswitches.Shouldyouwishto
connectthisunittoatimedsystempleaseconsultthe
manufacturerbeforeinstallation.
Specification
Voltage: 240V50Hza.c.
Lamp: 1612T35A-2x35WT5Fluorescent
 1612T35W-2x35WT5Fluorescent
IPrating: 20
Layout
• Planthedesiredlayoutofthisfittingcarefully,
ensuringthecableswillreachthedistancebetween
thejunctionboxandthelightfitting.
• Avoidlocatinganycablesinpositionsthatwould
causeahazard.Positioncablesandjunctionboxes
(notsupplied)awayfromareaswheretheymaybe
atriskfrombeingcut,trappedordamaged.
• Themainssupplycablemusthaveaminimumcross
sectionalareaof1.0mm².
• Ensuretheceilingiscapableofholdingtheweightof
theproduct.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingthe
existingfittingorceilingrose,carefullynotethe
positionofeachsetofwires.
• Ensurethattheceilingcansupporttheweightofthe
product.
• Drillholes800mmapart,andfitthesupplied
hooksintotheceilingusingthefixingssupplied.
Otherfixingsmayberequired,dependinguponthe
surface.
• Feedthewirethroughthependantnut,andthenthe
decorativecup.Loopthesteelwiresover,asshown,
andsecureusingthewirefixer.
• Hangtheloopoverthehookasshown.Feedthe
supplycablethroughthedecorativecupwiththe
hole.4.Pushthedecorativecupsintoplace.Secure
thesupplycableusingthecablegrips.
• Screweachpendantnutintopositiononthelight
fitting,youmayneedanassistantforthisoperation.
• Removethetopoftheballastcoverbyundoingthe
screwontheside.Feedthewirethroughthehole
attheend,ensuringthatthegrommetiscorrectly
locatedinthehole.
Installation
Wiring
Check that...
• Youhavecorrectlyidentifiedthewires
• Theconnectionsaretight
• Noloosestrandshavebeenleftoutoftheconnection
block.
NEUTRAL
EARTH (GREEN/YELLOW)
SWITCHED LIVE
BLUE (N)
GREEN/YELLOW
BROWN (L)
SUPPLY LIGHT FITTING
Havingcorrectlyidentifiedthewiringfromyourexisting
lightfitting,pullthewirethroughtheholeandconnectto
theconnectionblockinsidetheproductinthefollowing
way:
• Refit the cover into position, and secure using the
screw.
• Replacefuseor circuitbreaker andswitch on.Your
lightisnowreadyforuse.
Commissioning
Supply Cable
Decorative Cup
Wire Fixer
Wire
Cable Grip