Schaffner Ecosine evo FN3440 Operating manual

Schaffner EMV AG
Nordstrasse 11e |4542 Luterbach |Switzerland |Main [phone] |schaffner.com
USER AND INSTALLATION MANUAL
Ecosine evo Passive Harmonic Filters

1/62 User and installation manual Ecosine evo Passive Harmonic Filters
Revision: 09 (April 2023)
English version (original instructions)
The most current edition of this document (PDF format) can be obtained from your contact of the
Schaffner organization or at schaffner.com/downloads.
Other technical documentation of our products is also available in the download area of our website
schaffner.com.
Document name:
User and installation manual Ecosine evo Passive Harmonic Filters rev09.pdf
Valid for Ecosine evo Passive Harmonic Filters version:
FN3440/FN3441 (50 Hz) for 380–415 VAC
FN3450/FN3451 (50 Hz) for 440–500 VAC
FN3442/FN3443 (60 Hz) for 380–415 VAC
FN3452/FN3453 (60 Hz) for 440–480 VAC
Version history
Revision
Date
Description
01
November 2016
Initial version
02
February 2017
FN3441/51/53 and IP 20 types added
03
July 2017
SCCR
04
January 2018
Update filter selection table of FN3441/51/53 (min. required Lac, Ldc
included)
05
October 2018
Add new filter series FN3442 and FN3443 (60 Hz, 380VAC)
06
January 2019
Power terminal table (Table 1) updated.
Additional information regarding connecting power terminals with TDJ
module in the way added
07
September 2019
Filter earth terminal table (Table 1) updated.
Add new filters FN3440/41-250-119 and FN3450/51-315-119 and
information about the applied new frame size J
08
October 2020
Template harmonization
Typo corrections. Better harmonization of technical terms within the
document and between products line
Weight update (design change for some versions)
Section 3.1 to 3.4 correction of the MTBF rated voltage.
Rework of section 3.6 for addition of trap disconnect jumper terminals
cables requirement and harmonization.
Section 3.7 added - thermal switch specifications
09
April 2023
Template update for new branding
Section 3.5.2 current derating by altitude, new calculation.
Dimensions correction for frame size G dimension Z IP00

User and installation manual Ecosine evo Passive Harmonic Filters 2/62
i. Ecosine evo passive harmonic filter product
highlights
Schaffner ecosine evo passive harmonic filters are configurable products which provide a tailored
solution to each specific problem of current harmonics mitigation of 3-phase non-linear loads.
The eight product lines, FN3440/FN3441, FN3450/FN3451, FN3442/FN3443 and FN3452/FN3453 are
applicable for low voltage 50 Hz and 60 Hz systems and they are particularly suitable for AC and DC
motor drives, battery chargers and other power electronics applications with 6-pulse front-end rectifiers.
Ecosine evo passive harmonic filter technology represents an evolution of the previous generations of
passive harmonic filters and introduces following aspects of novelty:
|Ecosine evo is designed for the most demanding harmonic mitigation tasks. Ecosine evo
filters FN3440, FN3450, FN3442 and FN3452 are designed for three-phase diode and thyristor
rectifier, to achieve THDi ≤5% even without DC-link choke included in the drive. If there is 8%
DC link choke present in the drive, ecosine evo filters FN3441, FN3451, FN3443 and FN3453
help to achieve 5% THDi @ rated power. The new generation ecosine evo filters guarantee
compliance with the toughest requirement of IEEE-519 and other stringent international power
quality standards.
|Ecosine evo demonstrates superior partial load performance. The excellent performance
of ecosine evo filters not only reflects on mitigating harmonic current and bringing the THDi
down to 5% (diode rectifiers @ rated power), but also introducing minimum reactive power, even
at partial or no-load condition. The displacement power factor remains at cosφ >0.98 @ 50%
load.
|The modular concept of ecosine evo offers optimal tailored solution. Ecosine evo are con-
figurable filters, optional modules include fan with aux. power supply, fan without aux. power
supply, trap disconnect jumper and RC damper modules. Optimal solutions can be achieved by
merely plugging a new module according to different installation conditions and drive setups.
|Most compact design, robust, reliable and ready to use.
|The Schaffner ecosine evo product configurator (myecosine.com) supports customers in eval-
uating the best suited filter type.
|The upgraded version of the Schaffner power quality simulator SchaffnerPQS3
(pqs.schaffner.com) provides the possibility to simulate ecosine evo passive harmonic filters
within an electrical system. It furthermore offers quick and accurate performance checks.
This user manual is intended to support designers, installers, and application engineers with filter
selection, installation, application, and maintenance. It provides helpful solutions to overcome harmonics
mitigation challenges and answers frequently asked questions.
If you require additional support, please feel free to contact your local Schaffner representative.
ii. Performance Guarantee
By selecting and installing the appropriate ecosine evo passive harmonic filter in a variable frequency
AC drive application, variable speed drive application within our published technical specifications, we
guarantee that the input current distortion will be less than or equal to 5% THDi for standard ecosine
evo series filters at rated power. Ecosine evo filters can also provide similar performance in other drive
applications such as constant torque, DC drives or other phase controlled rectifiers, e.g. SCR drives,
but actual THDi levels can vary by load and/or speed and/or firing angle of thyristors and therefore
cannot be guaranteed. Consult your local Schaffner representative for assistance when applying
ecosine filters on these types of equipment.

3/62 User and installation manual Ecosine evo Passive Harmonic Filters
iii. Minimum system Requirements
The guaranteed performance levels of this filter will be achieved when the following system conditions
are met:
|Type of load: Any 3-phase equipment with front-end six-pulse diode rectifier, with
(FN3441/43/51/53) or without DC-link choke (FN3440/42/50/52).
|Type of source: 3-phase power line without neutral
|Line impedance: <3% (calculated for the rated filter power)
|Line frequency: 50 Hz ±1 Hz (FN3440/41, FN3450/51), 60 Hz ±1 Hz (FN3442/43, FN3452/53)
|Line voltage: Nominal line voltage ±10%
|Line voltage unbalance: <1%
|Line voltage distortion: THVD <2%
If a properly sized and installed filter fails to meet the 5% THDi level, Schaffner will provide the necessary
application engineering support or filter replacement at no charge.
iv. Important user notice
Schaffner ecosine evo harmonic filters are designed for the operation on the input (grid) side of power
electronic equipment with six-pulse rectifier front-ends in balanced three-phase power systems, like
typically used in AC or DC motor drives and high power DC supplies. Filter suitability for a given
application must be determined by the user on a case by case basis. Schaffner will not assume liability
for any consequential downtimes or damages resulting from use or application of ecosine filters outside
of their specifications. Ecosine filters are not designed for single-phase or split-phase applications.

User and installation manual Ecosine evo Passive Harmonic Filters 4/62
v. General Safety Notes and Installation Guidelines
(Cautions and Warnings)

5/62 User and installation manual Ecosine evo Passive Harmonic Filters
Table of Contents
1Ecosine evo passive harmonic filter designation..........................8
1.1 Distinguishing between FN3440/FN3441, FN3450/FN3451, FN3442/FN3443
and FN3452/FN3453.................................................................................................. 8
1.2 Explanation of ecosine evo designation ....................................................... 8
1.2.1 Examples of ecosine evo filter designations ....................................................................... 10
2Filter selection................................................................................11
2.1 Filter selection table FN3440/FN3441 (50 Hz, 3×380 … 415 VAC).............. 14
2.2 Filter selection table FN3450/FN3451 (50 Hz, 3×440 … 500 VAC).............. 16
2.3 Filter selection table FN3442/FN3443 (60 Hz, 3×380 … 415 VAC).............. 18
2.4 Filter selection table FN3452/FN3453 (60 Hz, 3×440 … 480 VAC).............. 20
2.5 Filter configurations and designations if external air flow is available for
cooling..................................................................................................................... 22
2.7 Filter configurations and designation with embedded ventilation............ 23
2.9 Filter configurations and designation if external aux. power supply for the
fan is available........................................................................................................ 24
2.10 Frame size J Filter configuration (FN3440/41-250-119, FN3450/51-315-119)
25
3Filter description............................................................................26
3.1 General electrical specifications FN3440/FN3441 (50 Hz filters)............... 26
3.2 General electrical specifications FN3450/FN3451 (50 Hz filters)............... 27
3.3 General electrical specifications FN3442/FN3443 (60 Hz filters)............... 28
3.4 General electrical specifications FN3452/FN3453 (60 Hz filters)............... 29
3.5 Additional electrical specifications.............................................................. 30
3.5.1 Clearance derating by altitude............................................................................................. 30
3.5.2 Current derating by altitude................................................................................................. 30
3.6 Screw size, torque and cable cross-section requirement.......................... 30
3.6.1 Power terminals................................................................................................................... 30
3.6.2 Trap disconnect jumper terminals ....................................................................................... 31
3.6.3 Auxiliary signal and earth terminals..................................................................................... 32

User and installation manual Ecosine evo Passive Harmonic Filters 6/62
3.7 Thermal protection switch specifications ................................................... 32
3.8 Cooling requirement...................................................................................... 33
3.9 Mechanical frame sizes................................................................................. 34
3.10 Ecosine evo filter footprint ........................................................................ 36
3.11 Filter performance ...................................................................................... 38
3.12 Functional diagram..................................................................................... 40
4Modular Design: How to choose optional modules.....................41
5Filter appearance and elements....................................................43
5.1 IP 00 version, frame size A - F...................................................................... 43
5.2 IP 00 version, frame size G - H ..................................................................... 44
5.3 IP 00 version, frame size J............................................................................ 44
5.4 IP 20 version .................................................................................................. 45
6Performance estimation using SchaffnerPQS.............................48
7Filter application ............................................................................49
8Filter installation ............................................................................50
8.1 Step 1: Visual inspection .............................................................................. 50
8.2 Step 2: Mounting............................................................................................ 50
8.3 Step 3: Wiring................................................................................................. 52
9Filter maintenance .........................................................................57
9.1 Maintenance schedule .................................................................................. 57
9.3 Fan.................................................................................................................. 58
9.4 Power capacitors........................................................................................... 58
9.5 Electrical connections................................................................................... 59
10 Trap circuit disconnect...............................................................60

7/62 User and installation manual Ecosine evo Passive Harmonic Filters
11 Troubleshooting..........................................................................61
12 Abbreviation ................................................................................61

User and installation manual Ecosine evo Passive Harmonic Filters 8/62
1 Ecosine evo passive harmonic filter designation
1.1 Distinguishing between FN3440/FN3441, FN3450/FN3451,
FN3442/FN3443 and FN3452/FN3453
Before going into the details of the designation, it is important to be aware of the difference between
FN3440 and FN3441, FN3450 and FN3451, FN3442 and FN3443, FN3452 and FN3453. FN3440,
FN3450, FN3442 and FN3452 are used for motor drives without dc-link choke. They are similar to
FN3441, FN3451, FN3443 and FN3453 except there is one choke less in FN3441, FN3451, FN3443
and FN3453 series as they are meant to be used for motor drives with dc-link choke (8%) included. In
other words, there are three chokes (line choke, trap choke and load choke) included in filter series
FN3440, FN3450, FN3442 and FN3452, whereas there are only two chokes (line choke, trap choke)
included in filter series FN3441, FN3451 FN3443 and FN3453 series.
By distinguishing between FN3440, (FN3450, FN3442, FN3452) as well as FN3441 (FN3451, FN3443,
FN3453) Schaffner is able to provide optimized solutions for different drive types:
| If there is no DC-link choke present in the motor drive, FN3440, FN3450, FN3442, FN3452
filter series help to reduce THDi to 5% @ rated power.
| If there is a minimum 8% DC-link choke present in the motor drive, FN3441, FN3451, FN3443,
FN3453 filter series reduce THDi to 5% @ rated power
In case you have difficulties selecting the right filter, please contact your local Schaffner representative
for support.
1.2 Explanation of ecosine evo designation
Ecosine evo is the new generation of Schaffner passive harmonic filter. They are introduced with a new
designation system, which contains of 4 sections connected with ‘-’ as shown in
Figure 1 Ecosine evo designation

9/62 User and installation manual Ecosine evo Passive Harmonic Filters
|The first part of the designation ‘FN34nn-xxx-yyy-_ _ _ _ _ _ _’ distinguishes between the six
ecosine evo filter series.
Table 1 filter application, operating frequency and nominal voltage per filter type
FN3440
FN3441
FN3450
FN3451
FN3442
FN3443
FN3452
FN3453
For 6-pulse diode rectifier
without DC-link choke
✓
✓
✓
✓
For 6-pulse diode rectifier
with 8% DC-link choke
✓
✓
✓
✓
For SCR rectifier
✓
✓
✓
✓
Operating frequency
50 Hz
50 Hz
60 Hz
60 Hz
Nominal operating voltage
3x 380 to 415
VAC
3x 440 to 500
VAC
3x 380 to 415
VAC
3x 440 to 480
VAC
|The second part of the designation ‘FN34nn-xxx-yyy-_ _ _ _ _ _ _’ indicates the motor drive
power rating, in kW for 50 Hz filters and in HP for 60 Hz filters. Please note that ecosine evo
filters are not using current rating in the designation anymore.
|The third part of the designation ‘FN34nn-xxx-yyy-_ _ _ _ _ _ _’ indicates the power terminal
type. For more information please see section 3.6.1.
|The fourth part of the designation ‘FN34nn-xxx-yyy- _ _ _ _ _ _ _’ contains seven slots, the
first two slots reveal the protection category of the filter, e.g. E0 and E2 represent IP 00 and IP
20 enclosure, while N1 and N3 represent NEMA type1 and NEMA type 3R, respectively. The
following five slots represent the presence (F,A,R,J,P) or absence (X) of optional modules in
the filter, as shown in
Figure 1. Please find more information in section 2.4, 2.5 and 2.6.

User and installation manual Ecosine evo Passive Harmonic Filters 10/62
Schaffner offers an online Product Configurator (myecosine.com) and the Schaffner Power Quality
Simulator SchaffnerPQS3 (pqs.schaffner.com) to select and verify the most suitable ecosine evo filter
for your application.
1.2.1 Examples of ecosine evo filter designations
FN3440-22-115-E0XXJRX: Filter for 50 Hz, 380–415 V AC grid, motor drive power rating 22kW without
DC-link choke present, with 20mm2 terminals, open frame (IP 00), filter contains trap disconnect jumper
module and RC damper module.
FN3441-22-115-E2FAXXX: Filter for 50 Hz, 380–415 V AC grid, motor drive power rating 22kW with
8% DC-link choke present, with 20mm2 terminals, IP 20 enclosure, filter contains Fan module and
auxiliary power supply module.
FN3452-150-116-E0XXXXX: Filter for 60 Hz, 440–480 V AC grid, motor drive power rating 150HP with
no DC-link choke present, with 24mm2 terminals, open frame (IP 00), filter contains no optional modules.
FN3440-250-119-E2FASXX: Filter for 50 Hz, 380–415 V AC grid, motor drive power rating 250kW with
no DC-link choke present, IP20, filter contains Fan module, auxiliary power supply module and switch
module.

11/62 User and installation manual Ecosine evo Passive Harmonic Filters
2 Filter selection
Ecosine evo passive harmonic filters need to be carefully selected and configured in order to enjoy
maximum benefits. Besides the enclosed selection tables and the product datasheets included in the
online configurator (myecosine.com), Schaffer advices to verify the selection by using the Schaffner
Power Quality Simulator tool SchaffnerPQS3, available at pqs.schaffner.com.
Step 1: Grid frequency
Determine, whether the system in consideration will be operated in a 50 Hz or 60 Hz electricity grid,
and select the corresponding filter series according to the following table:
50 Hz grid
Europe, Middle East, parts of Asia, parts of South America
FN3440/FN3441
FN3450/FN3451
60 Hz grid
North and Central America, parts of Asia, parts of South America
FN3442/FN3443
FN3452/FN3453
Note: a 50 Hz filter will not provide satisfying harmonics mitigation in a 60 Hz grid, and vice versa.
Step 2: Grid voltage
Verify that the grid configuration is suitable for standard ecosine evo passive harmonic filters accord-
ing to the following table:
50 Hz grid
Nominal voltage 380–415 V AC
TN, TT, IT configuration
50 Hz grid
Nominal voltage 440–500 V AC
TN, TT, IT configuration
60 Hz grid
Nominal voltage 380–415 V AC
TN, TT, IT configuration
60 Hz grid
Nominal voltage 440–480 V AC
TN, TT, IT configuration
Step 3: Rectifier type, presence of DC-link choke in drive
FN3440
FN3441
FN3450
FN3451
FN3442
FN3443
FN3452
FN3453
For 6-pulse diode rectifier
without DC-link choke
✓
✓
✓
✓
For 6-pulse diode rectifier
with 8% DC-link choke
✓
✓
✓
✓
For SCR rectifier
✓
✓
✓
✓
Note: For 6-pulse diode rectifier with DC-link choke smaller than 8%, it is recommended to choose
FN3440, FN3450, FN3442 or FN3452 if 5% THDi is required.

User and installation manual Ecosine evo Passive Harmonic Filters 12/62
Step 4: Rectifier/Drive input power
The individual filter must be selected with respect to the rectifier/motor drive input power in kW respec-
tively in HP. It is important to match rated filter power as close as possible with the effective input
power of the rectifier/drive.
Note that if the rectifier/drive is being operated very close to its rated power, then the filter can be se-
lected by the motor drive’s nominal power rating. However, if the drive will be operated e.g. at only
66% of its rated power, then a smaller filter should be selected in order to get maximum harmonics
mitigation performance and the optimum in terms of cost, size, and weight. In that case the customer
is responsible to ensure that ecosine passive harmonic filter will be operated within specification. This
is particularly important in terms of overload.
Please refer to the following examples:
Example 1:
Power line rating: 400 V, 50 Hz
Drive rating: 380–500 V, 50–60 Hz, 15 kW, 22.5 A, B6-diode rectifier without DC-link choke
Planned rectifier/drive input real power: 15kW (100% of drive rating)
➔Recommended filter according to the filter selection table FN3440: Type FN3440-15-113
Example 2:
Power line rating: 400 V, 50 Hz
Drive rating: 380–500 V, 50–60 Hz, 15 kW, 22.5 A, B6-diode rectifier with an 8% DC-link choke
Planned rectifier/drive input real power: 15 kW (100% of drive rating)
➔Recommended filter according to the filter selection table FN3441: Type FN3441-15-113
Example 3:
Power line rating: 500 V, 50 Hz
Drive rating: 380–500 V, 50–60 Hz, 15 kW, 18 A, B6-diode rectifier without DC-link choke
Planned rectifier/drive input real power: 15 kW (100% of drive rating)
➔Recommended filter according to the filter selection table FN3450: Type FN3450-15-113
Example 4:
Power line rating: 500 V, 50 Hz
Drive rating: 380–500 V, 50–60 Hz, 15 kW, 18 A, B6-thyristor rectifier
Planned rectifier/drive input real power: 15 kW (100% of drive rating)
➔Recommended filter according to the filter selection table FN3450: Type FN3450-15-113
Example 5:
Power line rating: 400 V, 50 Hz
Drive rating: 380–500 V, 50–60 Hz, 15 kW, 22.5 A, diode rectifier
Planned rectifier/drive input real power: 10 kW (66% of drive rating)
➔Recommended filter according to the filter selection table FN3440: Type FN3440-11-113
Example 6:
Power line rating: 480 V, 60 Hz
Drive rating: 380–500 V, 50–60 Hz, 30 HP, 41 A, diode rectifier
Planned rectifier/drive input real power: 30 HP (100% of drive rating)

13/62 User and installation manual Ecosine evo Passive Harmonic Filters
➔Recommended filter according to the filter selection table FN3452: Type FN3452-30-113
Oversizing of passive harmonic filters is not recommended because of the inherent lower harmonic
mitigation performance at partial load as well as higher cost, size, and weight.
Please refer to Table 2 - Table 9 to select suitable filters.

User and installation manual Ecosine evo Passive Harmonic Filters 14/62
2.1 Filter selection table FN3440/FN3441 (50 Hz, 3×380 … 415 VAC)
Table 2 FN3440 filter selection table
Filter
Rated
load
power
@400
V/50 Hz
Motor
drive
input
current
Rated
filter
input
current
Weight
Typical
losses
Terminal
Frame
size
[kW]
[Arms]***
[Arms]
[kg]
[W]****
FN3440-1-110-E0_____*
1.1
3
1.63
7
61
110
A
FN3440-2-110-E0_____*
2.2
5.5
3.26
10
87
110
A
FN3440-4-112-E0_____*
4
10
5.93
13
135
112
B
FN3440-6-112-E0_____*
5.5
13
8.17
17
183
112
C
FN3440-8-112-E0_____*
7.5
16
11.1
21
256
112
C
FN3440-11-113-E0_____
11
24
16.3
28
287
113
D
FN3440-15-113-E0_____
15
32
22.2
32
359
113
D
FN3440-19-113-E0_____
19
38
28.2
33
343
113
D
FN3440-22-115-E0_____
22
45
32.5
48
460
115
E
FN3440-30-115-E0_____
30
60
44.4
49
570
115
E
FN3440-37-115-E0_____
37
75
54.8
60
581
115
E
FN3440-45-115-E0_____
45
90
66.7
67
783
115
E
FN3440-55-115-E0_____
55
110
81.6
69
858
115
E
FN3440-75-116-E0_____
75
150
111
118
1036
116
G
FN3440-90-116-E0_____
90
180
134
139
1166
116
G
FN3440-110-118-E0_____
110
210
164
158
1365
118
H
FN3440-132-118-E0_____**
132
260
197
176
1392
118
H
FN3440-160-118-E0_____**
160
320
240
202
1462
118
H
FN3440-200-118-E0_____**
200
400
300
210
1644
118
H
FN3440-250-119-E0XXSXX
250
530
376
324
1746
119
J
* Filter rating which does not require forced cooling or fan module
** Filter rating which does not require RC damping module for rectifiers with EMI filter
*** Motor drive input current without harmonic filter
***** Typical losses @ 45°C, 400V, 50Hz and rated load power

15/62 User and installation manual Ecosine evo Passive Harmonic Filters
Table 3 FN3441 filter selection table
Filter
Rated
load
power
@400
V/50
Hz
Motor
drive
input
current
Rated
filter
input
current
Min.
required
Ldc
Min.
required
Lac
Weight
Typical
losses
Terminal
Frame
size
[kW]
[Arms]***
[Arms]
[mH]*****
[mH]*****
[kg]
[W]****
FN3441-1-110-E0_____*
1.1
1.7
1.62
37.41
9.8
6
53
110
A
FN3441-2-110-E0_____*
2.2
3.4
3.23
18.71
6.01
9
73
110
A
FN3441-4-112-E0_____*
4
6.2
5.9
10.29
3.48
12
104
112
B
FN3441-6-112-E0_____*
5.5
8.5
8.1
7.483
2.548
15
143
112
C
FN3441-8-112-E0_____*
7.5
12
11
5.487
1.818
16
193
112
C
FN3441-11-113-E0_____
11
17
16
3.741
1.264
23
233
113
D
FN3441-15-113-E0_____
15
23
22
2.744
0.909
26
285
113
D
FN3441-19-113-E0_____
19
29.3
28
2.166
0.724
30
271
113
D
FN3441-22-115-E0_____
22
34
32
1.871
0.637
38
355
115
E
FN3441-30-115-E0_____
30
46
44
1.372
0.454
43
452
115
E
FN3441-37-115-E0_____
37
57
54
1.112
0.361
48
468
115
E
FN3441-45-115-E0_____
45
70
66
0.915
0.297
54
596
115
E
FN3441-55-115-E0_____
55
85
81
0.748
0.245
63
665
115
E
FN3441-75-116-E0_____
75
116
110
0.549
0.178
98
757
116
G
FN3441-90-116-E0_____
90
140
133
0.457
0.147
106
854
116
G
FN3441-110-118-E0_____
110
171
162
0.374
0.12
127
1032
118
H
FN3441-132-118-E0_____**
132
205
195
0.312
0.099
149
1062
118
H
FN3441-160-118-E0_____**
160
249
238
0.257
0.085
167
1073
118
H
FN3441-200-118-E0_____**
200
312
297
0.206
0.064
169
1228
118
H
FN3441-250-119-E0XXSXX
250
392
376
0.165
0.051
246
1398
119
J
* Filter rating which does not require forced cooling or fan module
** Filter rating which does not require RC damping module for rectifiers with EMI filter
*** Motor drive input current without harmonic filter
***** Typical losses @ 45°C, 400V, 50Hz and rated load power
***** In order to apply FN3441 filters, motor drives have to be equipped with either DC-link choke or AC line choke. The
minimum required inductance values are given in mH in the filter selection table. If neither DC-link choke nor AC line
choke is present, or if the minimum mH rating is not fulfilled, FN3441 filter must not be used. In this case, FN3440 need
to be chosen.

User and installation manual Ecosine evo Passive Harmonic Filters 16/62
2.2 Filter selection table FN3450/FN3451 (50 Hz, 3×440 … 500 VAC)
Table 4 FN3450 filter selection table
Filter
Rated load
power @480
V/50 Hz
Motor
drive
input
current
Rated
filter input
current
Weight
Typical
losses
Terminal
Frame
size
[kW]
[Arms]***
[Arms]
[kg]
[W]****
FN3450-1-110-E0_____*
1.1
1.5
1.35
6
49
110
A
FN3450-2-110-E0_____*
2.2
3
2.75
8
76
110
A
FN3450-4-112-E0_____*
4.4
5.5
4.99
11
132
112
B
FN3450-6-112-E0_____*
5.5
10
6.77
14
135
112
B
FN3450-8-112-E0_____*
7.5
13
9.24
17
183
112
C
FN3450-11-112-E0_____*
11
16
13.6
21
256
112
C
FN3450-15-113-E0_____
15
24
18.5
28
287
113
D
FN3450-19-113-E0_____
19
32
23.3
32
376
113
D
FN3450-22-113-E0_____
22
38
27.0
36
374
113
D
FN3450-30-115-E0_____
30
45
36.9
48
460
115
E
FN3450-37-115-E0_____
37
60
45.4
54
546
115
E
FN3450-45-115-E0_____
45
75
55.2
63
598
115
E
FN3450-55-115-E0_____
55
90
67.5
67
784
115
F
FN3450-75-115-E0_____
75
110
92.5
88
1036
115
F
FN3450-90-116-E0_____
90
150
111
120
1016
116
G
FN3450-110-116-E0_____
110
180
135
141
1083
116
G
FN3450-132-118-E0_____
132
210
163
161
1440
118
H
FN3450-160-118-E0_____**
160
260
198
181
1412
118
H
FN3450-200-118-E0_____**
200
320
248
217
1597
118
H
FN3450-250-118-E0_____**
250
400
310
244
1745
118
H
FN3450-315-119-E0XXSXX
315
425
392
331
2025
119
J
* Filter rating which does not require forced cooling or fan module
** Filter rating which does not require RC damping module for rectifiers with EMI filter
*** Motor drive input current without harmonic filter
***** Typical losses @ 45°C, 480V, 50Hz and rated load power

17/62 User and installation manual Ecosine evo Passive Harmonic Filters
Table 5 FN3451 filter selection table
Filter
Rated
load
power
@480
V/50 Hz
Motor
drive
input
current
Rated
filter
input
current
Min.
required
Ldc
Min.
required
Lac
Weight
Typical
losses
Terminal
Frame
size
[kW]
[Arms]***
[Arms]
[mH]*****
[mH]*****
[kg]
[W]****
FN3451-1-110-E0_____*
1.1
1.4
1.3
53.9
16.7
5
40
110
A
FN3451-2-110-E0_____*
2.2
2.8
2.7
26.9
7.85
7
61
110
A
FN3451-4-112-E0_____*
4
5.1
4.9
14.8
4.47
10
104
112
B
FN3451-6-112-E0_____*
5.5
7.1
6.7
10.8
3.48
12
104
112
B
FN3451-8-112-E0_____*
7.5
9.6
9.2
7.90
2.55
15
143
112
C
FN3451-11-112-E0_____*
11
14.1
13.4
5.39
1.82
17
193
112
C
FN3451-15-113-E0_____
15
19.3
18.3
3.95
1.26
24
233
113
D
FN3451-19-113-E0_____
19
24.4
23.0
3.12
1.02
27
292
113
D
FN3451-22-113-E0_____
22
28.0
27.0
2.69
0.88
31
274
113
D
FN3451-30-115-E0_____
30
38.5
36.6
1.98
0.64
38
355
115
E
FN3451-37-115-E0_____
37
47.5
45.0
1.60
0.527
43
426
115
E
FN3451-45-115-E0_____
45
58
55
1.32
0.451
49
458
115
E
FN3451-55-115-E0_____
55
71
67
1.08
0.357
54
611
115
F
FN3451-75-115-E0_____
75
97
92
0.790
0.265
70
781
115
F
FN3451-90-116-E0_____
90
116
110
0.660
0.218
100
740
116
G
FN3451-110-116-E0_____
110
142
135
0.540
0.176
108
799
116
G
FN3451-132-118-E0_____
132
170
162
0.450
0.149
130
1063
118
H
FN3451-160-118-E0_____**
160
207
197
0.370
0.118
149
1039
118
H
FN3451-200-118-E0_____**
200
259
246
0.300
0.094
183
1232
118
H
FN3451-250-118-E0_____**
250
324
308
0.240
0.073
208
1262
118
H
FN3451-315-119-E0XXSXX
315
410
392
0.188
0.059
252
1553
119
J
* Filter rating which does not require forced cooling or fan module
** Filter rating which does not require RC damping module for rectifiers with EMI filter
*** Motor drive input current without harmonic filter
***** Typical losses @ 45°C, 480V, 50Hz and rated load power
***** In order to apply FN3451 filters, motor drives have to be equipped with either DC-link choke or AC line choke. The
minimum required inductance values are given in mH in the filter selection table. If neither DC-link choke nor AC line
choke is present, or if the minimum mH rating is not fulfilled, FN3451 filter must not be used. In this case, FN3450 need
to be chosen.

User and installation manual Ecosine evo Passive Harmonic Filters 18/62
2.3 Filter selection table FN3442/FN3443 (60 Hz, 3×380 … 415 VAC)
Table 6 FN3442 filter selection table
Filter
Rated load
power @380
V/60 Hz
Motor
drive
input
current
Rated
filter
input
current
Weight
Typical
losses
Terminal
Frame
size
[kW]
[HP]
[Arms]***
[Arms]
[kg]
[lbs]
[W]****
FN3442-1-110-E0_____*
0.9
1.2
2
1.37
6
12.6
50
110
A
FN3442-2-110-E0_____*
1.7
2.4
4
2.74
8
17.4
67
110
A
FN3442-4-112-E0_____*
2.9
4
7
4.57
10
22
116
112
B
FN3442-6-112-E0_____*
4.4
6
11
6.91
13
29
132
112
B
FN3442-8-112-E0_____*
5.9
8
14
9.29
16
35
160
112
C
FN3442-12-112-E0_____*
8.7
12
21
13.8
18
40
237
112
C
FN3442-16-113-E0_____
11.9
16
27
18.5
27
60
294
113
D
FN3442-20-113-E0_____
15
20
34
23.1
31
68
351
113
D
FN3442-24-113-E0_____
17.4
24
44
27.8
36
79
354
113
D
FN3442-32-115-E0_____
23.8
32
52
37.2
46
101
459
115
E
FN3442-40-115-E0_____
29.3
40
66
46.2
51
112
571
115
E
FN3442-48-115-E0_____
35.6
48
83
55.6
59
130
589
115
E
FN3442-60-115-E0_____
44.3
60
103
69.3
60
132
821
115
F
FN3442-80-115-E0_____
59.4
80
128
92.5
82
181
1028
115
F
FN3442-100-116-E0_____
73.6
100
165
115
116
256
1067
116
G
FN3442-120-116-E0_____
88.7
120
208
139
137
302
1143
116
G
FN3442-160-118-E0_____
118
160
240
184
170
375
1538
118
H
FN3442-200-118-E0_____**
147.3
200
320
231
187
412
1411
118
H
FN3442-240-118-E0_____**
177.3
240
403
279
252
556
1775
118
H
* Filter rating which does not require forced cooling or fan module
** Filter rating which does not require RC damping module for rectifiers with EMI filter
*** Motor drive input current without harmonic filter
***** Typical losses @ 45°C, 380V, 60Hz and rated load power

19/62 User and installation manual Ecosine evo Passive Harmonic Filters
Table 7 FN3443 filter selection table
Filter
Rated load
power @380
V/60 Hz
Motor
drive
input
current
Rated
filter
input
current
Min.
required
Ldc
Min.
required
Lac
Weight
Typical
losses
Terminal
Frame
size
[kW]
[HP]
[Arms]***
[Arms]
[mH]*****
[mH]*****
[kg]
[lbs]
[W]****
FN3443-1-110-E0_____*
0.9
1.2
1.4
1.37
21.5
11.61
5
11
41
110
A
FN3443-2-110-E0_____*
1.7
2.4
2.9
2.74
18.2
6.145
7
15
53
110
A
FN3443-4-112-E0_____*
2.9
4
4.8
4.52
10.7
3.602
9
20
88
112
B
FN3443-6-112-E0_____*
4.4
6
7.2
6.85
7.04
2.374
12
25
101
112
B
FN3443-8-112-E0_____*
5.9
8
9.6
9.20
5.25
1.771
14
30
123
112
C
FN3443-12-112-E0_____*
8.7
12
14.4
13.7
3.56
1.201
16
34
183
112
C
FN3443-16-113-E0_____
11.9
16
19.3
18.3
2.61
0.880
23
51
228
113
D
FN3443-20-113-E0_____
15
20
24.0
23.0
2.06
0.696
26
56
277
113
D
FN3443-24-113-E0_____
17.4
24
29.0
27.5
1.78
0.600
30
66
282
113
D
FN3443-32-115-E0_____
23.8
32
38.5
36.8
1.30
0.434
37
82
370
115
E
FN3443-40-115-E0_____
29.3
40
48.0
45.8
1.06
0.357
42
92
453
115
E
FN3443-48-115-E0_____
35.6
48
58.0
55
0.869
0.293
48
106
476
115
E
FN3443-60-115-E0_____
44.3
60
72.0
69
0.699
0.236
49
108
634
115
F
FN3443-80-115-E0_____
59.4
80
97.0
92
0.521
0.176
68
149
779
115
F
FN3443-100-116-E0_____
73.6
100
120
114
0.421
0.142
97
214
788
116
G
FN3443-120-116-E0_____
88.7
120
144
138
0.349
0.118
113
250
831
116
G
FN3443-160-118-E0_____
118
160
192
183
0.262
0.089
138
305
1199
118
H
FN3443-200-118-
E0_____**
147.3
200
240
229
0.210
0.071
152
336
1022
118
H
FN3443-240-118-
E0_____**
177.3
240
290
277
0.175
0.059
205
452
1292
118
H
* Filter rating which does not require forced cooling or fan module
** Filter rating which does not require RC damping module for rectifiers with EMI filter
*** Motor drive input current without harmonic filter
***** Typical losses @ 45°C, 380V, 60Hz and rated load power
***** In order to apply FN3443 filters, motor drives have to be equipped with either DC-link choke or AC line choke. The
minimum required inductance values are given in mH in the filter selection table. If neither DC-link choke nor AC line
choke is present, or if the minimum mH rating is not fulfilled, FN3443 filter must not be used. In this case, FN3442 need
to be chosen.