Schmalz SCPSi-L User manual

Compact Ejector SCPSi-L
Operating Instructions
WWW.SCHMALZ.COM EN-US · 30.30.01.02084 · 02 · 12/20

Note
The Operating instructions were originally written in German. Store in a safe place for future reference.
Subject to technical changes without notice. No responsibility is taken for printing or other types of er-
rors.
Published by
© J.SchmalzGmbH, 12/20
This document is protected by copyright. J.SchmalzGmbH retains the rights established thereby. Repro-
duction of the contents, in full or in part, is only permitted within the limits of the legal provisions of
copyright law. Any modifications to or abridgments of the document are prohibited without explicit writ-
ten agreement from J.SchmalzGmbH.
Contact
J. Schmalz GmbH
Johannes-Schmalz-Str. 1
72293 Glatten, Germany
T: [phone]
[email protected]
www.schmalz.com
Contact information for Schmalz companies and trade partners worldwide can be found at:
www.schmalz.com/salesnetwork
2 / 72 EN-US · 30.30.01.02084 · 02 · 12/20

Contents
EN-US · 30.30.01.02084 · 02 · 12/20 3 / 72
Contents
1 Important Information ...................................................................................................................................6
1.1 Note on Using this Document ............................................................................................................ 6
1.2 The technical documentation is part of the product ........................................................................ 6
1.3 Type Plate ............................................................................................................................................ 6
1.4 Warnings in This Document................................................................................................................ 6
1.5 Symbol.................................................................................................................................................. 7
2 Fundamental Safety Instructions...................................................................................................................8
2.1 Safety ................................................................................................................................................... 8
2.2 Intended Use........................................................................................................................................ 8
2.3 Non-Intended Use ............................................................................................................................... 9
2.4 Personnel Qualifications ..................................................................................................................... 9
2.5 Modifications to the Ejector ............................................................................................................... 9
3 Product Description ......................................................................................................................................10
3.1 Ejector Designation ........................................................................................................................... 10
3.2 Ejector Structure................................................................................................................................ 10
3.3 Display and Operating Element in Detail ........................................................................................ 11
4 Technical Data ...............................................................................................................................................13
4.1 Display Parameters ............................................................................................................................ 13
4.2 General Parameters........................................................................................................................... 13
4.3 Electrical Parameters ......................................................................................................................... 13
4.4 Factory Settings ................................................................................................................................. 14
4.5 Performance Data ............................................................................................................................. 15
4.6 Dimensions......................................................................................................................................... 15
4.7 Pneumatic Circuit Plans..................................................................................................................... 16
5 Operating and Menu Concept .....................................................................................................................17
5.1 Enabling the Menu............................................................................................................................ 17
5.2 Individual Functions .......................................................................................................................... 17
5.3 Main Menu ........................................................................................................................................ 18
5.4 Configuration Menu ......................................................................................................................... 18
5.5 System Menu ..................................................................................................................................... 20
6 Operating Modes ..........................................................................................................................................21
6.1 SIO Operating Mode ......................................................................................................................... 21
6.2 IO-Link Operating Mode................................................................................................................... 21
6.2.1 Process Data ...............................................................................................................................22
6.2.2 Parameter Data.......................................................................................................................... 22
6.2.3 IO-Link ........................................................................................................................................ 22
7 General Description of Functions ................................................................................................................23
7.1 Picking up the Workpiece (Vacuum Generation)............................................................................ 23
7.2 Depositing the Workpiece (Blowing Off) ........................................................................................ 23
7.3 Operating Modes .............................................................................................................................. 24
7.3.1 Automatic Operation ................................................................................................................24
7.3.2 Manual Operating Mode ..........................................................................................................24
7.3.3 Setup Mode................................................................................................................................ 25

Contents
4 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
7.4 Vacuum Monitoring .......................................................................................................................... 25
7.5 Control Function................................................................................................................................ 25
7.6 Blow off Functions ............................................................................................................................ 26
7.7 Monitoring the Supply Voltages ...................................................................................................... 27
7.8 Evaluating the Inlet Pressure ............................................................................................................ 27
7.9 Calibrating the Vacuum Sensor ........................................................................................................ 27
7.10 Signal Output .................................................................................................................................... 28
7.11 Signal Type......................................................................................................................................... 28
7.12 Control Concept for NO Ejectors ...................................................................................................... 28
7.13 Control Concept for NC Ejectors....................................................................................................... 29
7.14 Vacuum unit ...................................................................................................................................... 29
7.15 Switch-off Delay ................................................................................................................................ 29
7.16 ECO Mode .......................................................................................................................................... 29
7.17 Write Protection ................................................................................................................................ 30
7.18 Resetting to Factory Settings............................................................................................................ 30
7.19 Counters............................................................................................................................................. 31
7.20 Displaying the Software Version ...................................................................................................... 31
7.21 Displaying the Part Number ............................................................................................................. 31
7.22 Displaying the serial number............................................................................................................ 32
7.23 Production Setup Profiles ................................................................................................................. 32
7.24 Error Display ...................................................................................................................................... 32
7.25 Energy and Process Control (EPC)..................................................................................................... 33
7.25.1 Condition Monitoring (CM) ...................................................................................................... 33
7.25.2 Energy Monitoring (EM) ........................................................................................................... 35
7.25.3 Predictive Maintenance (PM).................................................................................................... 36
7.25.4 Diagnostic Buffer....................................................................................................................... 37
7.25.5 EPC Data Buffer .........................................................................................................................37
7.25.6 EPC Values in the Process Data ................................................................................................. 37
8 Transport and Storage..................................................................................................................................39
8.1 Checking the Delivery ....................................................................................................................... 39
9 Installation.....................................................................................................................................................40
9.1 Installation Instructions..................................................................................................................... 40
9.2 Mounting ........................................................................................................................................... 40
9.3 Pneumatic Connection ...................................................................................................................... 41
9.3.1 Connecting the Compressed Air and Vacuum ......................................................................... 41
9.3.2 Instructions for the Pneumatic Connection ............................................................................. 42
9.4 Electrical connection ......................................................................................................................... 42
9.4.1 PIN Assignment.......................................................................................................................... 44
9.4.2 PIN Assignment in IO-Link Mode.............................................................................................. 44
9.5 Start of Operations............................................................................................................................ 44
10 Operation ......................................................................................................................................................45
10.1 Safety Instructions for Operation..................................................................................................... 45
10.2 General Preparations ........................................................................................................................ 45
10.3 Typical Suction Cycles........................................................................................................................ 46
11 Troubleshooting............................................................................................................................................49
11.1 Help with Faults................................................................................................................................. 49

Contents
EN-US · 30.30.01.02084 · 02 · 12/20 5 / 72
12 Warnings and Errors .....................................................................................................................................50
12.1 Error Messages in SIO Operation...................................................................................................... 50
12.2 Warnings and Error Messages in IO-Link Mode .............................................................................. 50
12.3 System Status Light in IO-Link Mode ............................................................................................... 51
13 Maintenance..................................................................................................................................................52
13.1 Safety ................................................................................................................................................. 52
13.2 Cleaning the Ejector.......................................................................................................................... 52
13.3 Removing the Ejector Module.......................................................................................................... 52
13.4 Opening and Cleaning the Ejector Module..................................................................................... 53
13.5 Cleaning the Press-in Screen............................................................................................................. 53
13.6 Replacement of the Device with a Parameterization Server.......................................................... 53
14 Warranty........................................................................................................................................................55
15 Spare and Wearing Parts, Accessories.........................................................................................................56
15.1 Spare and wearing parts................................................................................................................... 56
15.2 Accessories ......................................................................................................................................... 56
16 Decommissioning and Recycling..................................................................................................................58
16.1 Disposing of the Ejector.................................................................................................................... 58
16.2 Materials Used ................................................................................................................................... 58
17 Attachment....................................................................................................................................................59
17.1 Overview of the Display Codes......................................................................................................... 59
17.2 EC Conformity.................................................................................................................................... 60
17.3 SCPSi_V2 Data Dictionary 21.10.01.00065_02 2014-08-29.pdf........................................................ 61

Important Information
6 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
1Important Information
1.1Note on Using this Document
J.SchmalzGmbH is generally referred to as Schmalz in these Operating instructions.
These Operating instructions contain important notes and information about the different operating
phases of the product:
• Transport, storage, start of operations and decommissioning
• Safe operation, required maintenance, rectification of any faults
The Operating instructions describe the product at the time of delivery by Schmalz.
1.2The technical documentation is part of the product
1. For problem-free and safe operation, follow the instructions in the documents.
2. Keep the technical documentation in close proximity to the product. The documentation must be ac-
cessible to personnel at all times.
3. Pass on the technical documentation to subsequent users.
ðFailure to follow the instructions in these Operating instructions may result in injuries!
ðSchmalz is not liable for damage or malfunctions that result from failure to heed these instructions.
If you still have questions after reading the technical documentation, contact Schmalz Service at:
www.schmalz.com/services
1.3Type Plate
The type plate (1) is permanently attached to the
ejector at the location shown and must always be
clearly legible.
The type plate contains the following informa-
tion:
• Pneumatic symbol
• QR code
• Part sales designation/type
• Part number
• Manufacturing date
• Serial number
• Permitted pressure range
• Operating voltage
1
1.4Warnings in This Document
Warnings warn against hazards that may occur when handling the product. This document contains three
levels of danger that you can recognize by the signal word.
Signal word Meaning
WARNING Indicates a medium-risk hazard that could result in death or serious injury if
not avoided.
CAUTION Indicates a low-risk hazard that could result in minor or moderate injury if not
avoided.
NOTE Indicates a danger that leads to property damage.

Important Information
EN-US · 30.30.01.02084 · 02 · 12/20 7 / 72
1.5Symbol
This symbol indicates useful and important information.
üThis symbol represents a prerequisite that must be met prior to an operational step.
4This symbol represents an action to be performed.
ðThis symbol represents the result of an action.
Actions that consist of more than one step are numbered:
1. First action to be performed.
2. Second action to be performed.

Fundamental Safety Instructions
8 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
2Fundamental Safety Instructions
2.1Safety
The ejector emits noise due to its use of compressed air.
WARNING
Noise pollution due to the escape of compressed air
Hearing damage!
4Wear ear protectors.
4The ejector must only be operated with a silencer.
WARNING
Uncontrolled movements of system components or falling of objects caused by in-
correct activation and switching of the Ejector while persons are in the plant
(safety door opened and actuator circuit switched off)
Serious injury
4Ensure that the valves and ejectors are enabled via the actuator voltage by installing a
potential separation between the sensor and actuator voltage.
4Wear the required personal protective equipment (PPE) when working in the danger
zone.
CAUTION
Depending on the purity of the ambient air, the exhaust air can contain particles,
which escape from the exhaust air outlet at high speed.
Eye injuries
4Do not look into the exhaust air flow
4Wear eye protection
2.2Intended Use
The ejector is built in accordance with the latest standards of technology and is safe to operate upon de-
livery; however, hazards can still arise during use.
The ejector is designed to generate a vacuum for gripping and transporting objects when used in conjunc-
tion with suction cups. It is operated by a controller with discrete signals or via IO-Link.
Neutral gases are approved as evacuation media. Neutral gases include air, nitrogen and inert gases (e.g.
argon, xenon and neon).
The product is intended for industrial use.
Intended use includes observing the technical data and the installation and operating instructions in this
manual.

Fundamental Safety Instructions
EN-US · 30.30.01.02084 · 02 · 12/20 9 / 72
2.3Non-Intended Use
WARNING
Extraction of hazardous media, liquids or bulk material
Personal injury or damage to property!
4Do not extract harmful media such as dust, oil mists, vapors, aerosols etc.
4Do not extract aggressive gases or media such as acids, acid fumes, bases, biocides, dis-
infectants or detergents.
4Do not extract liquids or bulk materials, e.g. granulates.
Schmalz accepts no liability for damages caused by non-intended usage of the ejector.
In particular, the following are considered non-intended use:
• Filling pressurized containers, driving cylinders, valves or other pressure-operated functional ele-
ments
• In potentially explosive atmospheres
• Use in medical applications
• Lifting people or animals
• Evacuation of objects that are in danger of imploding
• Ballistic applications
2.4Personnel Qualifications
Unqualified personnel cannot recognize dangers and are therefore exposed to higher risks!
1. Task only qualified personnel to perform the tasks described in these Operating instructions.
2. The product must be operated only by persons who have undergone appropriate training.
These Operating instructions are intended for fitters who are trained in handling the product and who
can operate and install it.
2.5Modifications to the Ejector
Schmalz assumes no liability for consequences of modifications over which it has no control:
1. The ejector must be operated only in its original condition as delivered.
2. Use only original spare parts from Schmalz.
3. The ejector must be operated only in perfect condition.

Product Description
10 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
3Product Description
3.1Ejector Designation
The breakdown of the item designation (e.g. SCPSi-L HF 3-16 NC RD M12-5 PNP) is as follows:
Property Variants
Type of ejector SCPSi-L, version with display
SCPS-L, version with bar display
Shape HF for “High Flow”
HV for “High Vacuum”
Nozzle size 2-07 / 2-09 / 2-13 / 2-16 / 3-16 / 3-20
Controller NO for “normally open”
NC for “normally closed”
Control RD for “with control”
No specification for “without control”
Electrical connection M12-5 connector
Signal type for signal inputs and out-
puts
NPN
PNP
3.2Ejector Structure
2
3
4
5
1 6
78
1 1/2" vacuum connection 2 Mounting hole (2x)
3 Display and control element 4 M12 electrical connection
5 1/4" compressed air connection 6 Ejector nozzle (covered)
7 Silencer with thread and snap closure 8 Exhaust outlet

Product Description
EN-US · 30.30.01.02084 · 02 · 12/20 11 / 72
3.3Display and Operating Element in Detail
Simple ejector operation is ensured with 3 buttons, the 3-digit display and 4 LEDs for status information.
8 1 2 3 4
567
1MENU BUTTON 2 Display
3 LED vacuum limit value H1 4 DOWN BUTTON
5UP BUTTON 6 LED vacuum limit value H2
7 LED process state “suction” 8 LED process state “blow off”
Definition of the LED Indicators
The “suction” and “blow off” process states are each assigned an LED.
Display Ejector state
LEDs both off No suction from ejector
LED for the suction function is constantly lit Ejector is applying suction or in control mode
LED for the blow off function is constantly
lit
Ejector blowing off

Product Description
12 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
Meaning of the Vacuum Limit Value LEDs
The LEDs for the vacuum limit values H1 and H2 indicate the current level of the system vacuum relative
to the configured limit values. Their display is independent of the switching function and assignment of
the output, and independent of whether the condition monitoring function is active.
Display Ejector state
LEDs both off Rising vacuum:
Vacuum < H2
Falling vacuum:
Vacuum < (H2-h2)
H2 LED lit steadily Rising vacuum:
Vacuum > H2 and < H1
Falling vacuum:
Vacuum > (H2-h2) and < (H1-h1)
Both LEDs lit steadily Rising vacuum:
Vacuum > H1
Falling vacuum:
Vacuum > (H1-h1)

Technical Data
EN-US · 30.30.01.02084 · 02 · 12/20 13 / 72
4Technical Data
4.1Display Parameters
Parameter Value Unit Comment
Display 3 Digit Red 7-segment LED display
Resolution ±1 mbar —
Accuracy ±3 % FS Tamb= 25°C, based on FS (full-scale) final value
Linearity error ±1 % —
Offset error ±2 mbar After zero-point adjustment, without vacuum
Temperature influ-
ence
±3 % 5° C < Tamb < 50° C
Display refresh rate 5 1/s Only affects the 7-segment display
Idle time before the
menu is exited
1 min The display mode is accessed automatically when no set-
tings are made in a menu.
4.2General Parameters
Parameter Symbol Limit value Unit Comment
min. typ. max.
Working temperature Tamb 0 --- 50 °C ---
Storage temperature TSto -10 --- 60 °C ---
Humidity Hrel 10 --- 90 % r.h. Free from condensation
Precision of vacuum sen-
sor
± 3% FS (full scale)
Degree of protection --- --- --- IP65 --- ---
Operating pressure (flow
pressure)
P 2 4.2 6 bar ---
Operating medium Air or neutral gas, 5µm filtered, with or without oil, class 3-3-3 com-
pressed air quality in acc. with ISO 8573-1
4.3Electrical Parameters
Parameter Symbol Limit values Unit Comment
min. typ. max.
Supply voltage USA 22.8 24 26.4 V DC PELV1)
Power consumption from US/A
2) with NO variant
IS/A — 50 4) 120 mA US/A = 24.0V
Power consumption from US/A
2) with NC variant
IS/A — 40 4) 70 mA US/A = 24.0V
Voltage of signal output (PNP) UOH US/SA-2 — VS/SA VDC IOH < 140mA
Voltage of signal output
(NPN)
UOL 0 — 2 VDC IOL < 140mA
Power consumption of signal
output (PNP)
IOH — — 140 mA Short-circuit-proof 3)
Power consumption of signal
output (NPN)
IOL — — -140 mA Short-circuit-proof 3)
Voltage of signal input (PNP) UIH 15 — UA/SA VDC In reference to GndA/
SA
Voltage of signal input (NPN) UIL 0 — 9 VDC In reference to UA/SA

Technical Data
14 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
Parameter Symbol Limit values Unit Comment
Current of signal input (PNP) IIH — 5 — mA —
Current of signal input (NPN) IIL — -5 — mA —
Reaction time of signal inputs tI— 3 — ms —
Reaction time of signal out-
puts
tO1 — 200 ms Adjustable
1) The power supply must correspond to the regulations in accordance with EN60204 (protected extra-low
voltage). The signal inputs and outputs are all protected against reverse polarity.
2) Plus the output currents
3) The signal output is protected against short circuits. However, the signal output is not protected
against overloading. Constant load currents > 0.15A may lead to impermissible heating and therefore the
destruction of the ejector.
4) Mean value
4.4Factory Settings
Code Parameter Value of the factory setting
X-1 Limit value H1 750mbar
h-1 Hysteresis value h1 150mbar
X-2 Limit value H2 550mbar
h-2 Hysteresis value h2 10mbar
XP1 Limit value H1 4.0bar
hp1 Hysteresis value hP1 0.2bar
tbL Blow off time 0.2s
ctr Control Activated = on
dc5 Continuous suction Deactivated = off
t-1 Evacuation time 2s
-L- Leakage value 250mbar/s
bLo Blow off function Externally controlled blow off = -E-
uni Vacuum unit Vacuum unit in mbar = -bA
tYP Signal Type PNP switching = PnP
dLY Switch-off delay 10ms
dPY Display rotation Standard = 5td
Eco ECO mode Deactivated = oFF
Pin PIN User-defined 000
o-2 Signal Output “Normally open” contact = no
The production setup profiles P-1 to P-3 are factory-set to have the exact same data set as the default
data set P-0.

Technical Data
EN-US · 30.30.01.02084 · 02 · 12/20 15 / 72
4.5Performance Data
Type SCPSi-L-
2-07 HV
SCPSi-L-
2-09 HV
SCPSi-L-
2-13 HF
SCPSi-L-
2-16 HV
SCPSi-L-
3-16 HV
SCPSi-L-
3-20 HV
Nozzle size [mm] 0.7 0.9 1.3 1.6 2.0
Max. vacuum1 [%] 85 61 90
Suction rate1 [l/min] 37 70 145 129 227 323
Max. blow off capacity 1 [l/
min]
130
Air consumption 1 (suction)
(l/min]
22 45 71 98 102 172
Sound level1, unobstructed
suction [dBA]
74 77 76 77 80 81
Sound level1, suction [dBA] 62 63 72 77
Weight [kg] 0.5
1) at 4.5 bar
4.6Dimensions
B B1 H H1 H3 Y1 Y2 X1 X2
17.6 37.5 95.75 109 56.5 35 28 40 28
G1 G2 G3 G4 L L3 L4 D d
1/4" inter-
nal thread
1/2" inter-
nal thread
M12x1 ex-
ternal
thread, 5-
pin
M4 inter-
nal thread
Max. 230 21 11.5 29 4.5
All specifications are in mm

Technical Data
16 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
4.7Pneumatic Circuit Plans
SCPSi-L...NO... SCPSi-L...NC...

Operating and Menu Concept
EN-US · 30.30.01.02084 · 02 · 12/20 17 / 72
5Operating and Menu Concept
The parameters can also be set using three buttons. The current system status and the settings are shown
on a display.
The unit is operated via three buttons on the foil keypad. Settings are configured using software menus.
The operating structure is divided into settings in the main menu and configuration menu. Setting the
ejector in the main menu is sufficient for standard applications. The advanced configuration menu is
available for applications with special requirements.
If settings are changed, undefined states of the system may occur for a short time (for approx. 50ms).
5.1Enabling the Menu
Menus can be protected against unauthorized access by defining a PIN [Pin] in the configuration menu.
When the lock is active, [Loc] flashes on the display or the PIN is requested.
The menus are accessed as follows:
1. Press the button
ðThe display changes to input
2. Use the or buttons to enter the first digit of the PIN
3. Confirm using the button
4. Enter the remaining digits in the same way.
5. To enable the device using the menu, press the button
The lock is activated again automatically after you leave the selected menu or close the function.
The PIN [000] must be set for permanent deactivation of the lock.
Tips and Tricks for Parameter Setting
• By pressing the or button for approx. 3 seconds, the value to be changed is
scrolled through quickly
• If you exit the changed value by briefly pressing , the value will not be applied.
5.2Individual Functions
Displaying the vacuum level:
Outside of the menu, the ejector is in display mode and the current vacuum level is displayed.
In display mode, a specific function is assigned to each key.
Displaying the supply voltage:
4Press the button
ðThe supply voltage that is currently applied to the ejector is displayed in volts.
After 3 seconds, the screen returns to the vacuum display.
The displayed voltage is a guideline value and is used for comparative measurements.
Displaying the operating mode:
4Press the button
ðThe current operating mode is displayed.
It is either standard I/O (SIO) mode [510] or IO-Link mode [10L].

Operating and Menu Concept
18 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
In IO-Link mode, you can also press the button again to view the IO-Link Standard (1.0, 1.1) that is cur-
rently in use.
After 3 seconds, the screen returns to the vacuum display.
5.3Main Menu
All the settings for standard ejector applications can be configured and read through the main menu:
1. Open the main menu by pressing the button.
2. Use or to select the desired adjustable parameter.
3. Confirm the selection with the key.
4. Use the or keys to set the value of the parameter.
5. To save and exit the menu, press and hold the key for at least 2 seconds.
ðThe displayed value flashes to confirm.
The following table shows an overview of the display codes in the main menu:
Display code Parameter Explanation
x-1 Vacuum limit value H1 Value at which the control function deactivates
(only if ctr = on and oN5 are active)
h-1 Hysteresis value h-1 Hysteresis value for the control function
x-2 Vacuum limit value H2 “Part Present” check switching value
h-2 Hysteresis value h-2 “Part Present” check hysteresis value
tbL Blow off time Only activated for E-t or l-t
CAL Calibration Calibrate the vacuum sensor
The factory settings for the parameters are listed in the Technical Data section.
5.4Configuration Menu
An extended configuration menu is available for applications with special requirements.
1. Open the configuration menu by pressing the button for more than 3 seconds.
ðDuring activation, [-C-] appears.
2. The parameters are set in accordance with the description in the Main Menu section.
The following table shows an overview of the display codes in the configuration menu:
Display
code
Parameter Possible settings Explanation
ctr Air saving func-
tion
on
oFF
on5
Control active
Control inactive
Valve protection function active (max. permissi-
ble leakage is monitored)
dC5 Deactivate auto.
control shutoff
on
oFF
Suppresses the automatic valve protection func-
tion when set to YE5.
Cannot be activated when Ctr = off .

Operating and Menu Concept
EN-US · 30.30.01.02084 · 02 · 12/20 19 / 72
Display
code
Parameter Possible settings Explanation
t-1 Max. permissi-
ble evacuation
time
Configurable be-
tween 0.01 and
9.99s in 0.01 incre-
ments
off
Permissible evacuation time; evaluation in IO-
Link only
No monitoring
-L- Max. permissi-
ble leakage
Values from 0 to
999mbar/s can be
configured in
1mbar/s increments
Menu item only displayed when ctr = On5
Unit: millibar per second
This value is used for onS and CM warnings. The
adjustable leakage value can be used to judge
the quality of the suction process. Evaluation in
IO-Link only.
bLo Blow off func-
tion
-E-
1-t
E-t
Externally controlled
Internally controlled (triggered internally, time
can be set)
Externally controlled (triggered externally, time
can be set)
o-2 Signal output 2
no
nc
Configure output 2, “Part Present” check
for normally open
for normally closed
tYP Signal Type
PnP
nPn
Define signal type for inputs and outputs
Signal type PNP, input/output on = 24V
Signal type NPN, input/output on = 0V
dLY H2 switching
signal delay
Values: 10, 50,
200 and oFF
Delays the switching signals X1 and X2
Unit: milliseconds
uni Vacuum unit
-bA
-ix
-PA
Define the displayed vacuum unit
Vacuum level in mbar
Vacuum level in inHg
Vacuum level in kPa
dPY Display rotation
5td
Red
Display configuration
Standard
rotated 180°
Eco Display in ECO
mode oFF
on
Configure the display
ECO mode is deactivated – the display remains
on
ECO mode is activated – the display switches off
Pin PIN Value from 001 to
999
Specify the PIN, lock the menus
If the PIN is 000, then the device is not locked.
rE5 Reset YES Set all parameter values to factory settings.
The factory settings for the parameters are listed in the Technical Data section.

Operating and Menu Concept
20 / 72 EN-US · 30.30.01.02084 · 02 · 12/20
5.5System Menu
A special menu is available for reading out system data such as counters, the software version, part num-
bers and serial numbers.
1. Open the system menu by simultaneously pressing the and buttons for more than 3 seconds.
ðDuring activation, -5- appears.
2. The parameters are set in accordance with the description in the Main Menu section.
The following table shows an overview of the display codes in the system menu:
Display code Parameter Explanation
cc1 Counter 1 Suction cycles
cc2 Counter 2 Number of valve switches
5oC Software function Software on the internal controller
Type Part number Format of the part no., example: 10.02.02.00383
5nr Serial number Provides information about the production period